不锈钢绕带容器环板与绕带端头的焊接

本文通过焊接试验对奥氏体不锈钢绕带容器环板与绕带焊接工艺进行了研究分析,并得出了合理的焊接方法和工艺参数。     

Production of biodiesel from waste fryer grease using mixed methanol/ethanol system

Transesterification of waste fryer grease (WFG) containing 5–6 wt.% free fatty acid (FFA) was carried out with methanol, ethanol, and mixtures of methanol/ethanol maintaining the oil to alcohol molar ratio of 1:6, and initially with KOH as a catalyst. Mixtures of methanol and ethanol were used for transesterification in order to use the better solvent property of ethanol and rapid equilibrium using methanol. Formation of soap by reaction of FFA present in WFG with KOH instigated difficulty in the separation of glycerol from biodiesel ester. To untangle this problem, two-stage (acid and alkali catalyzed) method was used for biodiesel synthesis. More than 90% ester was obtained when two-stage method was used compared to ∼ 50% ester in single stage alkaline catalyst. In the case of mixed alcohol, a relatively smaller amount of ethyl esters was formed along with methyl esters. Acid value, viscosity, and cetane number of all the esters prepared from WFG were within the range of the ASTM standard. Esters obtained from WFG showed good performance as a lubricity additive.     

高合金铁基烧结材料在轧钢导位中的应用研究

本文研究了高合金铁基烧结材料在轧钢导位中的应用。实验表明,通过粉末冶金液相烧结技术,可以获得具有优良综合性能的制品,材料密度ρ≥7.5 g/cm3,硬度≥55 HRC,抗弯强度≥1 000 MPa,冲击韧度αk≥3.9 J/cm2,满足了轧钢导位辊的工作要求。材料利用率可达95%以上、降低了制备成本。使用寿命是普通轧辊寿命的3~6倍,适用于线材和小型型材的轧钢生产。     

铸件浸渗系统脱液机故障树的建立和分析

利用FTA方法对脱液机的各种故障进行系统分析,建立了脱液机的故障树,并对故障树进行定性分析.找出了影响脱液机可靠性的主要因素,提出了提高脱液机可靠性的相应措施.     

中山包水电站钢岔管设计

中山包水电站钢岔管在天生桥二级水电站 6号压力钢管下平段分岔 ,岔管HD值达 15 40m2 ,结构体形复杂 ,采用NK HITEN780A Z35和NK HITEN6 90B高强度钢材制造安装 ,在国内水电工程中实际应用较少。文章着重介绍岔管的布置、结构分析和焊缝的无损检验要求。中山包水电站的正常发电运行 ,为 80kg/mm2 级高强钢在国内水电行业的应用提供了第 3个成功实例     

自动焊技术在涩宁兰输气管道X70钢试验段上的应用

通过涩宁兰输气管道X70钢试验段的施工,进一步探索和完善自动焊接技术在高强钢管道焊接中的应用。文章介绍了该试验段施工的焊接设备、焊材和焊接工艺,可为同类焊接工程提供借鉴。     

固液相变蓄能的数学模型和自然对流换热系数的实验研究

引入自然对流换热系数 ,将固液蓄能数学模型简化为仅用能量方程加以描述。并通过实验测得相变过程的实际温度场 ,证明了自然对流固液相变换热的影响不可忽略 ,验证了固液相变界面移动速率随自然对流换热系数的增大而增大的定性关系     

Liquid crystalline polymers as additives to enhance the device properties of low molecular mass liquid crystals

Magnetic and electric fields have been used to determine the splay (k₁₁) and bend (k₃₃) elastic constants in a series of polymer/monomer liquid crystal solutions using the well known Freedericksz transition technique. Measurements have been carried out as a function of concentration and temperature. The polymer used was a smectogenic polysiloxane side chain liquid crystal with both cyanobiphenyl and benzoate ester side groups. The monomeric solvent was the nematogen 4-n-pentyl-4′-cyanobiphenyl. All of the solutions studied were nematogenic up to a concentration of 40% w/w. It has been shown that k₁₁, k₃₃ and $\text{k}{}_{33}\text{k}{}_{11}$ all decrease with increasing polymer concentration and that at high enough concentrations $\text{k}{}_{33}\text{k}{}_{11}$ tends to become independent of temperature. The implications of these results are discussed in terms of the performance of the most common liquid crystal display, i.e. the twisted nematic device.     

Recovery retardation in equal channel angular pressed Al–Zr alloy during friction stir welding

The effect of Zr on reduction of hardness and microstructure in an FS weld of equal channel angular-pressed Al alloy was investigated. Zr addition to Al suppressed dynamic recovery in the thermomechanically affected zone and enabled retention of the high hardness of the ECA-pressed material throughout the weld.     

Metallurgical failure analysis of cold cracking in a structural steel weldment: Revisiting a classic failure mechanism

Cold cracking of structural steel weldments is a well-characterized, well-documented, and well-understood failure mechanism. Extensive effort has been put forth to recognize the welding and materials selection parameters that are conducive to cold cracking; however, these engineering efforts have not fully eliminated the occurrence of such failures. This article describes cold cracking failure specifically related to the construction industry. This particular failure was successfully identified prior to final erection of the structural member, and the weld was successfully reworked. These actions potentially prevented a serious catastrophic event that could have occurred have occurred either later in the construction process or possibly during the use of the building. Individual welding parameters, such as electrode/wire selection, joint design, and pre/postheating, played a role in the failure, and a number of human factors relating to the actual fabrication practices also contributed to the failure process.