Remote Steering of Self‐Propelling Microcircuits by Modulated Electric Field

The principles and design of “active” self‐propelling particles that can convert energy, move directionally on their own, and perform a certain function is an emerging multidisciplinary research field, with high potential for future technologies. A simple and effective technique is presented for on‐demand steering of self‐propelling microdiodes that move electroosmotically on water surface, while supplied with energy by an external alternating (AC) field. It is demonstrated how one can control remotely the direction of diode locomotion by electronically modifying the applied AC signal. The swimming diodes change their direction of motion when a wave asymmetry (equivalent to a DC offset) is introduced into the signal. The data analysis shows that the ability to control and reverse the direction of motion is a result of the electrostatic torque between the asymmetrically polarized diodes and the ionic charges redistributed in the vessel. This novel principle of electrical signal‐coded steering of active functional devices, such as diodes and microcircuits, can find applications in motile sensors, MEMs, and microrobotics.     

Theoretical study of a thermoelectric-assisted vapor compression cycle for air-source heat pump applications

This paper proposes a thermoelectric-assisted vapor compression cycle (TVCC) for applications in air-source heat pump systems which could enhance the heating capacity of the system. Performances of TVCC are calculated and then compared with that of basic vapor compression cycle (BVCC). The simulation results show that when coefficients of performance (COPs) of the two cycles are almost equal, the TVCC under maximum COP condition of the thermoelectric modules still performs better than BVCC by 13.0% in heating capacity through selecting the appropriate intermediate temperature. In addition, the TVCC can also achieve an improvement of 16.4%–21.7% in both the heating COP and capacity when compared with the BVCC with an assistant electric heater that is provided with the equivalent power input of thermoelectric heat exchanger. Thus, the TVCC could be beneficial to the applications in small heat pumps if there is always need for auxiliary electric heat.     

Low cycle fatigue behavior of a eutectic 80Au/20Sn solder alloy

The eutectic 80Au/20Sn solder alloy is widely used in high power electronics and optoelectronics packaging. In this study, low cycle fatigue behavior of a eutectic 80Au/20Sn solder alloy is reported. The 80Au/20Sn solder shows a quasi-static fracture characteristic at high strain rates, and then gradually transforms from a transgranular fracture (dominated by fatigue damage) to intergranular fracture (dominated by creep damage) at low strain rates with increasing temperature. Coffin-Manson and Morrow models are proposed to evaluate the low cycle fatigue behavior of the 80Au/20Sn solder. Besides, the 80Au/20Sn solder has enhanced fatigue resistance compared to the 63Sn/37Pb solder.     

“Size effect” in the fatigue behavior of Friction Stir Welded plates

Comparative fatigue tests were carried out on Friction Stir Welded specimens of a 2195-T8 aluminum–lithium alloy that differed significantly in width. The width of the larger specimens was over thirteen times greater than that of the small specimens. Fatigue results showed a clear “size effect”, i.e. fatigue life of large specimens was about 40% of the corresponding value of small specimens. The Equivalent Initial Flaw Size methodology was adopted to correlate the two sets of results. Fatigue crack initiation life was disregarded with respect to crack propagation life, and fatigue life was evaluated only as propagation of a small pre-existing defect. Following this methodology, test results of small specimens were used to evaluate the initial equivalent flaw contained in each specimen. It was assumed that this data followed a normal distribution. The equivalent initial flaw in larger specimens was evaluated by simple geometrical considerations. A very good assessment of mean fatigue life and scatter in the fatigue results of large specimens was obtained by simulating the propagation of these defects. Calculations were carried out by taking also welding residual stresses into account, but the results demonstrated that this effect was not significant.     

住宅设计的分析与研究

总结了住宅设计的发展,概括了住宅各个功能区的特点。通过设计的实例说明了各不同功能区的设计,成果可供进一步的研究参考。     

“锲而不舍 金石可镂”——上海秀派公司2．45GHz有源RFID标签技术的成功之路

上海秀派公司坚持自己的技术长项——2．45GHz有源RFID,充分发扬该种RFID的特长,记者采访该公司时了解到了开发方面的很多细节、成功案例和实施经验。我们不但非常推崇该公司的“锲而不舍”的意志,而且还意识到如果秀派公司的成功经验一旦辐射到中国的RFID行业中,一定会把这项在国外诞生的技术更好地植根于中国的土壤,使之更加适合中国的实用环境。     

基于可靠性评价的含缺陷核压力管道疲劳寿命预测方法

含缺陷压力管道经缺陷评定合乎使用后,其疲劳寿命的估计具有重要的工程意义。将整个含缺陷压力管道作为一个整体,分析了含缺陷压力管道的疲劳裂纹扩展特点,提出了相应的含缺陷压力管道疲劳寿命的计算过程,并在基于可靠性评价的基础上,给出了核压力管道的可接受失效概率,最终得到了含缺陷核压力管道疲劳寿命预测方法。     

工业管道测厚的几点问题探讨

超声波测厚在腐蚀监测上应用越来越广泛,为让这项检测技术更准确、更可靠,充分发挥功效,文章就工业管道测厚中测厚数据处理、测厚点选择、高温问题以及其它影响因素等几个方面进行了探讨。     

加快塑料技术中心建设提高新产品开发水平

对中国石油化工集团公司(简称中国石化)合成树脂生产及加工应用技术的现状进行了分析，指出中国石化应加快建设塑料加工应用技术中心，为塑料产品的加工用户提供高技术水平和快捷周到的技术服务，在合成树脂新产品开发和产品结构调整中发挥积极作用，以提高合成树脂产品的市场竞争力。