Simulation by Slepian method of plastic displacements of Gaussian process excited multistory shear frame

The object of study is a stationary Gaussian white noise excited multi-degree-of-freedom (MDOF) linear elastic, ideal plastic, linearly damped, statically determinate oscillator with several potential elements of ideal plastic yielding. Specifically the study is exemplified for a plane multistory shear frame with rigid traverses where all the connecting columns except the columns in one or more of the bottom floors have finite symmetrical yield limits. The white noise excitation acts on the mass of the first floor making the movement of the elastic bottom floors simulate a ground motion that interacts with the structure above the bottom floors. The method of study is so-called Slepian model simulation and is in principle the same for other statically determinate MDOF elasto-plastic oscillators of the considered type. The method is fast as compared to direct simulation and provides results that give good insight in the behavior of the plastic displacement response process.     

转动玻璃圆筒激光器

本文介绍了转动玻璃圆筒激光器的设计及实验结果,得到了脉冲能量为13J,重复频率为15Hz的激光输出。电光转换效率为2.2％,斜效率为3.4％。     

炮孔内空气间隙作用的机理探讨

本文探讨了装药结构中空气间隙作用的机理,提出了气体分子的迁移效应与碰撞效应,比较完满地解释了不同空气间隙对爆破效果的影响.     

在建坝体中部分浆砌石的控制爆破拆除

某在建大坝部分浆砌石坝体因质量不合格须爆破拆除。保护余留坝体免受爆破影响是此工程的重点,为此,采用了小直径浅孔和微差爆破分层拆除方法,被拆除部分和被保护部分之间预留保护层。爆破施工过程中,利用超声波观测法和压水试验法判断被保护坝体是否受到了爆破震动的影响。根据判断结果,调整爆破参数,以减小爆破震动。文中论述了爆破参数的选择、保护层厚度的确定,同时介绍了安全控制技术、测点布置以及监测结果。     

低乙烯含量抗冲聚丙烯的结构表征

采用二甲苯为溶剂，将不同乙烯含量（５％￣１５％质量）的抗冲聚丙烯用特定程序进行分级，将各样品分为室温下可溶于甲苯和不可溶于甲苯的两部分。使用＾１３Ｃ－ＮＭＲ方法和ＦＴ－ＩＲ方法对各组分进行表征，明确了乙烯链段在聚丙烯链上的分布，并在此基础上提出了产生这种链结构的聚合工艺的特点。     

Finite elements in the analysis of pressure vessels and piping-a bibliography (1976–1996)

The paper gives a bibliographical review of the finite element methods (FEMs) applied for the analysis of pressure vessel structures/components and piping from the theoretical as well as practical points of view. The range of applications of FEMs in this area is wide and cannot be presented in a single paper; therefore the aim of this review is to give the reader an encyclopaedic view of the differnt possibilities that exist today for the finite element analysis in the fields of pressure vessels and piping. The bibliography at the end of the paper contains approximately 1900 references to papers, conference proceedings and theses/dissertations on the subject that were published in 1976–1996. These are classified in the following categories: linear and non-linear, static and dynamic, stress and deflection analysis; stability problems; thermal problems; fracture mechanics problems; contact problems; fluid-structure interaction problems; manufacturing of pipes and tubes; welded pipes and pressure vessel components; development of special finite elements for pressure vessels and pipes; finite element software; and other topics. Also finite element software, general purpose and special purpose codes, used for the analysis of pressure vessels and pipes are briefly discussed and presented.     

金属－橡胶硫化粘接过程中分子取向行为的间接证据

对金属－橡胶热硫化粘接复合体的剥离行为进行了研究，同一粘接试样的双向１８０°剥离试验显示出了巨大的差异。本文分析了弹性材料在硫化过程中的分子行为，并提出了相应的新假设，认为这是由于金属－橡胶在硫化粘接过程中分子取向交联行为所致。这种双向１８０°剥离破坏现象可被看作是金属－橡胶硫化粘接过程中分子取向行为的间接证据。     

脉冲波形对流化床性能的影响

本文从理论上分析了矩形波和正弦脉波气流对流化床操作性能的影响，发现矩形波在一定条件下优于正弦波的规律，并用实际进行了验证。     

Conceptual design of a high-efficiency absorption cooling cycle

The search for high-efficiency, gas-fired cooling cycles has led to the development of dual-loop absorption machines with cooling coefficients of performance (COPs) in the 1.2 to 1.7 range. This increased performance may call for high generator temperatures, new working fluids or new materials of construction. In most cases, two different sets of working fluids are required. The conceptual design presented here is aimed at obtaining high efficiencies with relatively low temperatures, employing only one set of fluids. The concept consists of two loops coupled in a configuration aimed at minimizing the loss of thermodynamic availability incurred when transferring refrigerant between the loops. The working fluid pair is a solution of lithium bromide-water. The calculated COPs are of the order of 1.8. The cycle relies on an elaborate evaporator-absorber combination. The paper presents the conceptual design, the critical assumptions, and the performance calculations for the concept.