On the pressure drop modeling of monofilament-woven fabrics

Pressure drop of monofilament-woven fabrics is often calculated via the so-called orifice model in which a discharge coefficient is assigned to the weave's unit cell. In all previous models of woven fabrics, the filaments were assumed to have circular cross-sections—an assumption which is not entirely accurate especially when there is a considerable tension in the warps and wefts. Following the methodology developed by Lu et al. [1996. Fluid flow through basic weaves of monofilament filter cloth. Textile Research Journal 66 (5), 311-323], a new set of expressions are derived for calculating the most constricted open area, and so the discharge coefficient, of plain-woven monofilament fabrics having filaments with elliptical cross-sections. Conducting numerical simulations for computing the pressure drop of such fabrics, we observed a logarithmic relationship between the discharge coefficient and the Reynolds number. It was also shown that the discharge coefficient decreases by increasing the aspect ratio of the filaments’ cross-section.     

Impac塔填料在冷却塔中的应用

在对比国内外冷却塔填料现场应用情况的基础上，总结了Impac塔填料及喷嘴应用的优势及存在的问题，说明了Impac塔填料热力性能传质传热效果及Lantc喷头的布水情况，通过经济效益对比分析表明，该填料及喷头具有良好的应用前景；同时，该填料具有施工安装方便等特点，对解决冷却塔冬季结冰也有好处，为冷却塔改造填料喷嘴的选型提供了新途径。     

强冷磨削的试验研究

进行了强冷磨削和干磨削试验。试验结果表明 ,磨削温度随工件速度和磨削深度的增大而增大 ,强冷磨削可显著降低磨削温度 ,在冷却压力小于 1MPa时 ,外冷却的冷却效果优于内冷却     

Release rates of tetradecen-1-ol acetates from polymeric formulations in relation to temperature and air velocity

An apparatus was developed for investigating the release rates of pheromone formulations at temperatures and air velocities that correspond with those in the field. Polyurethane foam proved an excellent adsorbent for the recovery of tetradecen-1-ol acetates, allowing high air flows at low differential pressure and without breakthrough of these compounds. The experimental setup and procedures are described. The release rates of all formulations investigated were almost proportional to the square root of air velocity, and their logarithms were proportional to the reciprocal of temperature (K). When temperature is increased from 15°C to 25°C, the release rates increase by about 2-2.5 ×. Both relationships were combined into one equation that allows a reliable estimate to be made of the actual release rates of a formulation, under varying conditions, on the basis of its specific parameters and the relevant meteorological data.     

基于现有结构的空压机的改造设计

针对无法完全发挥效能的某厂二手空压机设备 ,结合厂方提出的改造目标 ,提出可在现有总体结构布置的情况下 ,采用通流能力好的三元叶轮、增加流道宽度等措施进行结构改造。经编制热力设计程序进行分析计算 ,结果表明这一方案切实可行     

湿式空气氧化法处理乙烯废碱液装置的技术改造

针对中国石化齐鲁石化公司烯烃厂乙烯装置废碱液处理系统在试运转过程中存在的问题,通过分析原因,提出并实施改进工艺的相关措施,得到一组适宜的工艺操作参数,保证了废碱液湿式空气氧化装置的稳定运行。     

Advancements in the design and validation of an air pollution integrated assessment model for Spain

This paper describes the design and application of the Atmospheric Evaluation and Research Integrated model for Spain (AERIS). Currently, AERIS can provide concentration profiles of NO₂, O₃, SO₂, NH₃, PM, as a response to emission variations of relevant sectors in Spain. Results are calculated using transfer matrices based on an air quality modelling system (AQMS) composed by the WRF (meteorology), SMOKE (emissions) and CMAQ (atmospheric-chemical processes) models. The AERIS outputs were statistically tested against the conventional AQMS and observations, revealing a good agreement in both cases. At the moment, integrated assessment in AERIS focuses only on the link between emissions and concentrations. The quantification of deposition, impacts (health, ecosystems) and costs will be introduced in the future. In conclusion, the main asset of AERIS is its accuracy in predicting air quality outcomes for different scenarios through a simple yet robust modelling framework, avoiding complex programming and long computing times.     

Ozone Cooling Tower Treatment With and Without Mineral Removal

This paper builds on a prior paper by this author, McGrane (1991). In that paper, ozone is used as the sole means of cooling tower water treatment. The paper discusses water conservation by increased cycles of concentration, greatly increased efficiency through extremely low biological populations, and corrosion data which is compared to ozonated and chemically treated towers.

New in this paper are the results from the combination of a low pressure reverse osmosis system with ozone treatment for cooling tower water. Scale formation has continued to plague cooling towers with high concentrations of calcium in the make-up water. The use of a mineral removal system in cases of extremely hard water has made ozone an attractive alternative to traditional chemicals in many areas.     

空气气氛中烧成Si3N4-SiC复合材料的性能、相组成和显微结构

以氮化硅细粉(粒度＜0.088 mm,w(β-Si3N4)＞95%)、碳化硅(w(SiC)＞98%,粒度分别为2.8～0.9mm、0.9～0.15 mm、＜0.115 mm和＜0.063 mm四级)、硅粉(粒度＜0.045 mm,w(Si)＞98%)和硅灰(w(SiO2)=98.3%)为原料,以木质素磺酸钙水溶液作成型结合剂,采用150 MPa的压力成型为65 mm×114 mm×230mm的Si3N4-SiC、Si3N4-SiC-Si和Si3N4-SiC-SiO2三种试样.在空气气氛中,以50℃·h-1的升温速度升至800℃保温4 h,再升至1450℃保温2 h,自然冷却至室温后,测定烧成后试样的常温耐压强度、常温抗折强度、1400℃下的高温抗折强度、显气孔率、体积密度和残氮率,并采用XRD、SEM和EPMA等手段分析烧后试样的相组成和显微结构.结果表明3种试样在空气气氛中烧成后的高温(1400℃)和常温抗折强度都比较高,显气孔率都比较低,而耐压强度则以Si3N4-SiC试样的最高;烧成后试样中心区域的残氮率以Si3N4-SiC-Si试样的最高,Si3N4-SiC-SiO2试样的次之,Si3N4-SiC试样的最小;在空气气氛中烧成后,Si3N4-SiC试样中的Si3N4分解较多,SiC-Si3 N4-Si试样的表面和内部都明显含有单质Si,SiC-Si3N4-SiO2试样表面区域的Si2N2O晶体发育很好,而内部区域的晶体发育较小.     

CAE技术在解决胶带座注塑缺陷中的应用

介绍了CAE技术在注塑产品生产中的应用。针对胶带座在注塑成型过程中产生的缺陷，借助CAE软件验证了产生缺陷的位置，找出了产生缺陷的原因。并在工艺、模具和产品设计上进行了修改，从而解决了实际生产中遇到的问题，为实际生产提供了指导。