碳纤维表面处理对铝电解用硼化钛阴极涂层性能的影响

硼化钛阴极涂层是铝电解用可润湿性阴极材料中的一种，具有优良的抗钠渗透性和对铝液润湿性，可以有效地延长铝电解槽寿命。碳纤维是硼化钛涂层材料的增强剂之一．对硼化钛阴极涂层的性能影响很大。本文研究了不同工艺的液相碳纤维表面氧化处理法对硼化钛阴极涂层抗拉强度和粘接强度的影响。采用PTIR检测碳纤维处理后表面含氧基团的变化，寻找影响硼化钛阴极涂层性能的原因，从而达到最有效地提高TiB2阴极涂层抗拉强度和粘接强度的目的。结果表明，采用工艺(1)(10％HNO3，80℃、恒温5min．超声波、5min)对碳纤维进行表面处理最合理，处理后碳纤维表面含氧基团的含量最高．用其制备硼化钛阴极涂层的抗拉强度、粘接强度最大。     

Determination of generation lifetime fromC-t transients under linear voltage ramp bias

When a linear voltage ramp is applied to the gate of a MOS capacitor, a capacitancetime (C-t) transient is observed. The MOS capacitor is biased into strong inversion before applying the voltage ramp in order to eliminate surface generation. FromC-t transient curve obtained experimentally the minority carrier generation lifetime in semiconductor can be determined. The experimental results show that for the same sample the lifetimes extracted fromC-t curves under varying voltage sweep rates are close each other, and they are consistent with the lifetimes extracted by saturation capacitance method.     

Continuous Separation of Inclusions from Aluminum Melt Flowing in a Circular Pipe using a High Frequency Magnetic Field

The continuous separation of inclusions from aluminum melt flowing in a circular pipe using a high frequency magneticfield was investigated both theoretically and experimentally The separation efficiency was calculated based on thetrajectory method and compared with experimental results. It is found that the separation efficiency is a functilnondimensional parameters t_i·d_p~2B_e~2/μ_fμ_eα~2 and α/δ.The effective way to improve the separation efficiency is to increasethe effective magnetic flux density and decrease the pipe radius. and the value of α/δ should be kept about 2 in orderto obtain the optimum separation efficiency.     

超高纯铜的制备方法和应用

简要介绍了超高纯铜(UHPC)的几种精炼方法，以及它在工业方面的应用。并对超高纯铜的研究开发趋势及应用前景进行了展望。     

基于小波熵的电容器扰动识别和定位

对投电容器扰动识别和定位的方法进行了改进。针对其他此类方法的不足，比如在电压幅值低时投电容器扰动的识别、定位“可信度不高”等，文中通过提取小波变换的特定层的系数，对需要识别的电容器扰动的分解信号相对增强，而其他扰动的分解信号相对减弱，然后再提取熵特征值，结果表明它可以作为识别低电压时投电容器扰动的依据。在对电容器扰动进行定位时，参考了功率和能量定位法，并对其进行了改进。仿真分析证明，在电压幅值较低时，可以准确和可靠地对电容器扰动进行识别和定位。     

大型预焙铝电解槽使用碳化硅砖与普通碳砖复合块的探讨

碳化硅砖和碳化硅砖与普通碳砖复合侧块，在上世纪末期我国铝电解槽上开始推广应用。使用后各厂家普遍发现碳化硅砖及碳化硅砖与普通碳块复合侧块均出现不同程度的断裂、上抬和脱落现象，该文对断裂、上抬和脱落原因进行了分析，并提出了改进措施。     

Recovery retardation in equal channel angular pressed Al–Zr alloy during friction stir welding

The effect of Zr on reduction of hardness and microstructure in an FS weld of equal channel angular-pressed Al alloy was investigated. Zr addition to Al suppressed dynamic recovery in the thermomechanically affected zone and enabled retention of the high hardness of the ECA-pressed material throughout the weld.     

罐装食品用电镀锡板的耐蚀性及其试验方法

综述了影响罐装食品用电镀锡板耐蚀性能的因素及其试验方法。     

脉冲激光沉积SrBi2Ta2O9铁电薄膜电容特性研究

用ＰＬＤ方法成功地制备了ＳＢＴ铁电薄膜，并制作成Ｐｔ／ＳＢＴ／Ｐｔ薄膜电容器。ＳＢＴ薄膜的晶面取向以（００８）和（１１５）为主。在５Ｖ电压下，极化反转，并且得到较饱和的电滞回线，剩余极化强度和矫顽电场分别为８４μＣ／ｃｍ２和５７ｋｖ／ｃｍ。ＩＶ特性测试显示两个对称的双稳峰，并得到零电压下，面积为３１４×１０４μｍ２，厚度为０３５μｍ的电容器，电容约为５６０ｐＦ，介电常数约为６００。疲劳测试表明Ｐｔ／ＳＢＴ／Ｐｔ具有优良的抗疲劳特性。     

Effect of Iron on the Color of Barley and Other Cereal Porridges

ABSTRACT: Iron added as ferrous sulfate at 500 mg*kg⁻¹ to rice, oats, whole grain wheat, or proanthocyanidin-free barley porridge caused significant changes in the Hunter "L", "a", and "b" values but the visual appearance of these porridges remained satisfactory. Porridge made with normal barley flour fortified with 500 mg*kg⁻¹ of iron developed an unappealing gray color with ferrous sulfate, ferrous fumarate, or electrolytic iron, 3 salts differing in solubility. At 100 and 250 mg*kg⁻¹ of iron, the discoloration of normal barley porridge was less pronounced, but still objectionable. When fortified with 50 mg*kg⁻¹ of iron, normal barley porridge had a slight color change but was not noticeably gray. Thus barley-containing foods can be fortified with a soluble iron compound at the level of iron used in enriched flour and similar cereal-grain foods for the general population without developing an unattractive color.