抗弹陶瓷的犁削机理和自锐作用研究

研制了铬刚玉抗弹陶瓷，其抗弹能力比标准均质钢有很大的提高，通过分析讨论，其主要抗弹机制为犁削机理和自锐作用。     

The dynamics of the dry friction oscillator taking into account pre-displacement and tangential contact stiffness

A one-dimensional model of the dry friction oscillator is considered taking into account the phenomena of pre-displacement and tangential contact stiffness. The dynamic parameters and characteristics of the basic mode of stabilized vibrations are determined for the cases of force and kinematic excitation. The obtained results are compared with the Coulomb model of the force of friction, which gives evidence that this model is inapplicable to calculating low-amplitude oscillations. The effect of the tribological contact parameters on the resonance characteristics of the oscillator and the damping properties of the friction contact are investigated.     

Fault diagnosis as an aid to process machine reliability

Identification of the reasons for failures of process plant machines is the first step in obtaining increased reliability. Weibull analysis of the service life obtained from maintenance records requires a minimum of only five incidents and provides an insight into the failure mechanism. Two examples are given where Weibull analysis of maintenance records helped identify the cause of failure and was instrumental in achieving enhanced reliability of process plant machines.     

台达机电产品在高速集束球经机中的应用

本文主要介绍台达20PM运动控制器在纺织行业的高速集束球经机中的应用。阐述了球经机的技术特点和工艺要求,简介了控制系统的硬件配置和应用程序。在控制系统中利用20PM内置的多组电子凸轮功能实现了两边成型和精密绕排等各项工艺目标。     

Cu—Cr合金电极触头板铸件的熔制

含０．４％～１．０％Ｃｒ的Ｃｕ－Ｃｒ合金具有优良的导电、导热性能，铸件经热处理强化后可获得较高的综合力学性能。近年来该合金作为一种新材料被广泛地用于制作电子工业、电器设备上的电极触头板、接触环、夹持体等零件。Ｃｕ－Ｃｒ合金存在易氧化吸气、凝固范围窄、收缩较大、易形成集中缩孔等缺陷，这些铸造特性给生产优良的Ｃｕ－Ｃｒ合金铸件带来一定的困难。以采用常规的熔炼设备和造型材料熔铸出Ｃｕ－Ｃｒ合金铸件——高压大电流电极触头板为例讨论这一熔铸的工艺方法。     

水轮机下环铸件凝固过程热应力模拟分析

采用数值模拟方法对水轮机下环铸件凝固过程中的应力场进行了模拟和分析。模拟中采用接触单元法处理铸件与砂芯之间力的作用,改进了传统的铸件/铸型边界条件处理方法。文中重点分析了下环凝固过程中准固相区的受力情况,根据准固相区受力特点建立了适当的热裂判据,对下环凝固过程热裂倾向性进行预测。实际生产结果与预测结果相符合。     

圆坯连铸GCr15SiMn的成分偏析和接触疲劳寿命研究

利用金属原位分析技术和钻孔化学分析方法对高淬透性轴承钢GCr15SiMn的Φ450 mm连铸圆坯和Φ130 mm圆钢的C、Si、Mn、Cr元素横截面的分布情况进行分析。采用推力片式接触疲劳试验机进行了材料的接触疲劳寿命测试。结果表明：GCr15SiMn连铸圆坯C元素的偏析倾向较大,易产生中心正偏析,而Cr、Si、Mn元素的偏析倾向较小。通过采取稳定低过热度浇铸、三段强电磁搅拌等措施,铸坯的中心碳偏析得以改善。采用(1240±20)℃×5 h高温扩散、初轧首道次变形量≥90 mm大变形轧制的Φ130 mm圆钢的碳偏析可以得到进一步的改善,试验钢在5.3GPa高应力负载下的接触疲劳额定寿命L₁₀达到3.58×10⁶次,接近电渣重熔钢的水平。     

接触器特征参数测试仪

本文详细介绍了微机型接触器特征参数测试仪工作原理，软硬件及调试、运行和故障处理。     

Surface contact degradation of multilayer ceramics under cyclic subcritical loads and high number of cycles

Alumina/alumina–zirconia ceramic laminated composites produced by tape casting present a compressive residual stress at the alumina surface due to the thermal expansion mismatch between layers developed during processing. Because of this residual stress, the mechanical properties at the surface, such as wear or surface fracture, have proven to be better than the properties of a monolithic stress-free alumina. In a previous work, it was shown that this laminate composite has better resistance to the development of a ring crack when loaded with a spherical indenter, under both cyclic and static loads below the critical load for cone cracking. In this work, cyclic Hertzian indentations with subcritical loads are performed on the same laminate ceramic and a monolithic alumina, but with a higher number of cycles than the necessary to provoke the first damage (ring crack). Results show that for low and intermediate number of cycles, the laminated composite presents better resistance to damage than the monolithic alumina. However, for high number of cycles, spalling at the surface of the laminate material appears, whereas the monolithic alumina develops secondary cone cracking. This difference is attributed to the fact that laminate ceramics present an enhanced apparent fracture toughness of the material, which implies a higher quasi-plasticity due to shear driven microcracking. For a high number of cycles, these microcracks grow until coalescence at the surface, provoking exfoliation of the material at the contact area, enhanced by the fact that the indented and the indenter material have different elastic properties.     

The role of the surface free energy in the selection of a suitable excipient in the course of a wet-granulation method

Pellets containing metronidazole were produced in a centrifugal granulator, with hydroxypropylcellulose (Klucel LF®) as binding agent, and corn starch, microcrystalline cellulose (Vivapur 101®) and lactose as excipients. The wettability of the pharmaceutical powders was assessed by means of contact angle measurements, and the dispersive and polar surface energies were determined. The spreading coefficients, the work of adhesion and the work of cohesion were calculated and correlated with the pellet properties (friability, bulk and tapped density, and porosity). The aim was to investigate the role of the surface free energy of one- and two-component powder compositions in pellet production. The interactions between the particles were found to be connected with the measured pellet parameters. It was concluded that, in the course of the growth of the pellets, the particle sizes of the pharmaceutical powders and the interactions between them are important. If the work of cohesion of the binder is lower than the work of cohesion of the substrate and the work of adhesion, then the optimal amount of the binding agent is that which coats the particles uniformly in minimal quantity and in continuous layer.