以表面负载季铵盐阳离子型苯/丙乳胶粒为模板制备ZrO_2空心微球

以C9油与甲基丙烯酰氧乙基三甲基氯化胺的共聚物P(C9-DMC)为乳化剂制备苯/丙阳离子乳胶粒,并以其为模板,利用直接包覆法制备了由17 nm左右微晶体堆成的ZrO2空心微球。所制得的样品采用FT-IR、XRD、TEM和SEM等进行了表征。     

聚苯硫醚复合涂层的耐磨性能

研究了用固体润滑石墨、碳化硅、二硫化钼等填料改性的聚苯硫醚 (PPS)涂层的耐磨性能。实验结果表明 ,聚苯硫醚复合涂层具有优良的耐磨性 ;加入适量 ( 3 0 % )的石墨、碳化硅等固体润滑剂 (石墨 :碳化硅 =2∶3 ) ,可以有效提高涂层的耐磨性能 ,而二硫化钼和三氧化二铬的减摩效果更佳     

Effects of thermal and mechanical treatments on a titanium-based conversion coating for aluminium alloys

The influence of mechanical deformation and heating on the protective performance of a chromium-free conversion treatment for aluminium alloys has been assessed by polarisation and AC impedance measurements. Protection is unlikely to be seriously compromised by typical production operations.     

Improved Matrix-Filler Adhesion

Enhanced matrix-filler adhesion is realized after filler treatment with a surface treatment process. The hydrosol/coupling agent treatment was applied to a wide range of inorganic and organic fillers, and adhesion to a variety of matrix resins was improved. Scanning Electron Microscopy (SEM) was used to determine the locus of failure in the filled systems. The locus of failure shows the relative degree of adhesion between the filler and the polymer matrix. Significant improvement in adhesion in humid environments is also observed.     

Level set and geodesic active contours based measurement of material removal between serial sections

The measurement of the thickness of material removed between serial sections is a crucial step of three-dimension reconstruction. Geodesic active contours is an efficient method for contour detection of objects on an image. The indents on the SiC/Al composite micrographs are segmented by using level set and geodesic active contours. After getting the contours of the indents, we calculate the distance from the uppermost pixel to the lowermost pixel to get the vertical diagonal length, and calculate the distance from the leftmost pixel to the rightmost pixel to get the horizontal diagonal length of each contour. Then the final length of each diagonal is acquired by averaging the vertical diagonal length and the horizontal diagonal length, respectively. The Vickers’ indenter is made by a square pyramidal-shaped diamond with opposite faces at an angle of 136°, so the thickness of material removed between two serial sections and the length difference of the diagonals on the two serial sections has a definite geometrical relation. Thus the thickness of material removed between two serial sections is acquired using the geometrical relation.     

Measurement of the Timoshenko Shear Stiffness. II: Effect of Transverse Compressibility

This is the second of two papers devoted to the issue of measuring the Timoshenko shear stiffness of thin-walled composite beams. In the first paper, the effect of warping on the effective Timoshenko shear stiffness, as measured through bending tests, was studied. The bending test was simulated using finite-element analysis, and the results indicated that the warping effect was minimal. On the other hand, the evidence suggests that transverse flexibility may have a significant influence on the effective Timoshenko shear stiffness, decreasing the effective shear stiffness at shorter test spans. The purpose of the present study is to further investigate this effect and to explore the use of a sandwich theory to predict the measurement error. A higher-order sandwich theory, which captures the transverse strain at concentrated loads and supports, is applied to a commercially available thin-walled composite beam. The results indicate that the sandwich model does capture the decrease in the effective shear stiffness at short spans, and the dependence of the shear stiffness on span-to-depth ratio is similar to that calculated in the first paper, using the finite-element method.     

高合金钢铸造用涂料的试制与开发

介绍了炉爪用合金钢1Cr25Ni20Si2Re,导板用合金钢2Cr32Ni5采用串箱铸造过程中，有关镁砂粉涂料和石英粉涂料的试制。结果表明：镁砂粉涂料为不透气涂料，不太适用，而合理配方的石英粉涂料使用性能良好。     

Experimental Study on Polymer Artificial Bone with HA Coated and Fiber Liners

1Introduction HA(hydroxyapatite)wasakindofbioactiveceram ics,whichhadexcellentbiocompatibilityandtissueaffin ityinthatitscomponentsweresimilartothoseofhuman bone[1].Soitwasthebestknownhumanbonesubstitute,andunprecedentedeffecthadbeenharvestedinrecenttwo d…     

Plasma Sprayed Hydroxyapatite Coatings with Nano-hydroxyapatite Prepared by Ultrasonic Precipitation Process

Nano-particle hydroxyapatite （ HA ） was prepared with a novel ultrasonic precipitation process and the as-prepared nanopowder was used to produce hydroxyapatite （ HA ） coatings on titanium substrate via plasma spraying. The phase and the microstructare of the coating were characterized by X- ray diffraction （XRD） and scanning electron microscopy （SEM）. Results showed that spherical particles could be prepared by ultrasonic precipitation process; and a corresponding dense HA coating with molten surface and low-porosity cross-section structure was acquired. During the plasma spraying process, new phases of Ca3 （ PO4 ）2 and Ca2 P2O7 were generated. After heat-treating at 800℃ for 1 h, the contents of Ca3 （ PO4 ）2 and Ca2 P2O7 decreased while HA content increased. Tensile adhesion tests showed that the plasma sprayed coating prepared with the spherical nanoparticles exhibited high tensile bond strength.     

Water‐Stable,Magnetic Silica–Cobalt/Cobalt Oxide–Silica Multishell Submicrometer Spheres

A method to produce monodisperse magnetic composite spheres with diameters from less than 100 nm to more than 1 μm in water solution is reported. The spheres consist of a dielectric silica core and a cobalt/cobalt oxide shell which can be protected from further oxidation with an outer shell of silica or, alternatively, they can be covered with the polymer polyvinylpyrrolidone as a stabilizer. The formation of a uniform magnetic shell proceeds with the adsorption of metallic cobalt seeds, produced by the reduction of cobalt chloride with sodium borohydride, on a self‐assembled layer of polyelectrolytes on the silica core. In the second step, an outer silica shell can be formed by the hydrolysis and condensation of (3‐aminopropyl)trimethoxysilane and tetraethoxysilane. The double‐shell composite spheres show excellent sphericity, monodispersity, and a magnetic hysteresis loop at room temperature.