提高钻杆接头冲击功的工艺方法

针对石油钻井关键产品高强度钻杆接头的使用要求,在保证强度指标要求非常高的前提下,研究摸索增加高温正火后再调质的工艺方法,以改善接头材料原始微观带状组织和纤维结构,细化晶粒,提高钻杆接头的冲击功,使该产品力学性能达到API标准的要求。     

锻压机械打击力测量误差的加速度补偿

提出了锻压机械打击力测量中存在的问题，介绍了常用的补偿法，并通过实验验证了加速度补偿法是消除锻压机械打击力测量误差的有效途径。     

应用BP神经网络的单机架可逆式冷轧机弯辊力预设定

针对单机架可逆式冷轧机生产过程中，由于不同热轧生产厂的热轧板形原料性能、板形差别较大、从而造成弯辊力预设定值和实际指标相差较大的问题，利用现场生产工艺数据丰富，采用人工智能BP神经网络的方法，通过大量数据输入进行训练，大大的提高了生产过程中弯辊力预设定值的准确性。     

Effect of ultrasonic power and bonding force on the bonding strength of copper ball bonds

Copper wire, serving as a cost-saving alternative to gold wire, has been used in many high-end thermosonic ball bonding applications. In this paper, the bond shear force, bond shear strength, and the ball bond diameter are adopted to evaluate the bonding quality. It is concluded that the ef/~cient ultrasonic power is needed to soften the ball to form the copper bonds with high bonding strength. However, excessive ultrasonic power would serve as a fatigue loading to weaken the bonding. Excessive or less bonding force would cause cratering in the silicon.     

An investigation of laser-assisted machining of Al2O3 ceramics planing

Laser-assisted machining (LAM), an alternative method of fabricating difficult-to-machine materials, uses primarily laser power to heat the local area (without necessarily evaporating or melting any material) before the material is removed. It not only efficiently reduces the cutting force during the manufacturing process but also improves the machining characteristics and geography with regard to difficult-to-machine materials, especially structural ceramics.This study on the application of laser-assisted machining to Al₂O₃ ceramics examines the measurements of cutting force and workpiece surface temperature as well as surface integrity and tool wear. Specifically, it uses the lattice Boltzmann method (LBM) to calculate the temperature distribution inside the ceramic workpiece during the LAM process and ensure that the laser energy causes no subsurface damage. The experimental results reveal that the LAM process efficiently reduces the cutting force by 22% (feed force) and 20% (thrust force) and produces better workpiece surface quality than conventional planing.     

高速切削机床中的磁轴承

高效化是机械制造的永恒主题之一。本文简介了高速切削的理论依据及其优点，分析了磁悬浮轴承的原理、特点以及磁浮轴承在高速切削机床上的应用情况，从而说明了磁浮轴是高速切削机床最理想的轴承之一。     

Al-18%Si合金在梯度强磁场中凝固时初生硅的行为

研究了Al-18%Si合金在10 T梯度强磁场下加热至半固态和全熔态后的凝固过程,观察了初生硅的分布和形态,测定了其冷却曲线.结果表明:在磁场的磁感应强度和磁场梯度的乘积Bz·dBz/dz为正时,初生硅向上部聚集;而在Bz·dBz/dz为负时,初生硅向下部聚集;在强磁场下,加热至全熔态冷却下来的凝固组织中初晶硅的形态发生了明显的改变,由板片状转变为块状,初晶硅显著细化.对强磁场细化初晶硅的机制进行了探讨.     

奥氏体不锈钢车削时刀具磨损对切削因素和表面质量的影响研究

研究了奥氏体不锈钢车削加工过程中刀具后刀面磨损对切削力、切削温度、粗糙度及残余应力影响规律。试验结果表明:当刀具后刀面磨损在一定范围内,F_x与F_z随磨损量的增加而显著增大,而F_y基本保持不变;温度随刀具后刀面磨损量增加而显著增大;工件的表面粗糙度随刀具后刀面磨损量增大而增大;当车刀后刀面磨损为0.167 mm时,工件加工表面的残余应力最大。     

A critical analysis on the friction modelling in orthogonal machining

Despite the development of high performance finite element-based codes, the simulation of machining still represents a very hard task due to the geometric complexity of the real chip-tool systems and the high cutting speed that requires very long simulation times. For these reasons, many aspects related to machining are not very clear and so easy to simulate. In this paper a rigorous investigation on the role played by the implemented friction model within a 2D simulation of orthogonal cutting was carried out, taking into account different models proposed by the researchers in the last years. The main simulation results were compared with experimental measurements in order to verify if it is possible to identify the best model. Once the comparison with mechanical variables was completed, a subsequent study on temperature predictions utilizing the above friction models was executed as well. The results of this integrated numerical and experimental work are carefully reported in the paper.     

电磁成形中的测量

本文简要介绍了电磁成形中放电电流、管坯与线圈间隙中的磁场测量 ,以及管坯动态变形过程测量的各种方法。通过各种方法的比较分析 ,得出分流器法测放电电流、探测线圈法测感生磁场是切实可行的方法。金属坯料在电磁力作用下的变形过程可用撞针法和高速摄影的办法进行测量 ,每种方法各有其优势和适用范围 ,测量时 ,根据实际情况进行选用。