Procedures for analysis of strain transfer in the acetabular region in vitro

The failure of acetabular cups via loosening, migration or fracture is partially related to the stress distribution existing in the acetabular region. The complexity of the investigation of these stresses demands the application of a variety of model testing techniques involving combined embedded strain gauging, finite element analysis, transmission and reflective photoelasticity and crack propagation studies. The application of these procedures are described and the difficulties of obtaining representative loadings and restraints are commented upon.     

Detection of multiple cracks using frequency measurements

A method for detection of multiple open cracks in a slender Euler-Bernoulli beams is presented based on frequency measurements. The method is based on the approach given by Hu and Liang [J. Franklin Inst. 330 (5) (1993) 841], transverse vibration modelling through transfer matrix method and representation of a crack by rotational spring. The beam is virtually divided into a number of segments, which can be decided by the analyst, and each of them is considered to be associated with a damage parameter. The procedure gives a linear relationship explicitly between the changes in natural frequencies of the beam and the damage parameters. These parameters are determined from the knowledge of changes in the natural frequencies. After obtaining them, each is treated in turn to exactly pinpoint the crack location in the segment and determine its size. The forward, or natural frequency determination, problems are examined in the passing. The method is approximate, but it can handle segmented beams, any boundary conditions, intermediate spring or rigid supports, etc. It eliminates the need for any symbolic computation which is envisaged by Hu and Liang [J. Franklin Inst. 330 (5) (1993) 841] to obtain mode shapes of the corresponding uncracked beams. The proposed method gives a clear insight into the whole analysis. Case studies (numerical) are presented to demonstrate the method effectiveness for two simultaneous cracks of size 10% and more of section depth. The differences between the actual and predicted crack locations and sizes are less than 10% and 15% respectively. The numbers of segments into which the beam is virtually divided limits the maximum number of cracks that can be handled. The difference in the forward problem is less than 5%.     

A new curvature technique calculation for surface tension contribution in PLIC-VOF method

The volume of fluid (VOF) methods have been used for numerous numerical simulations. Among these techniques used to define the moving interface, the piecewise linear interface reconstruction (PLIC-VOF) is one of the most accurate. A study of the superficial tension impact on two-phase flow with free surface is presented. A new method based on direct staggered grid is developped to include surface tension in PLIC-VOF. The new numerical curvature calculation method doesn't need smoothed colour function and leads to less “spurious current”. This technique is applied to the calculus of surface tension force in the case of the rise of air bubble in viscous liquid and the fall of liquid drop in the same liquid on free surface. Droplets, thin layer and capillarity waves are observed after the free surface rupture for different Bond number. The influence of surface tension calculus is then obvioused and when the drop hit the free surface, wavelets propagate toward the virtual boundaries imposed.     

Complementary modelling of fluid separation processes

Optimal functioning of numerous technological processes depends primarily on relevant process design, properly selected column internals and sufficient understanding of the process behaviour. This can be achieved only with the help of accurate and reliable process models capable of considering process rates in a rigorous way, with respect to both transport phenomena and chemistry. In this article, a new modelling concept called complementary modelling is suggested for a large class of fluid separation processes. Since the conditions and criteria for these processes vary considerably, it is impossible to develop a unified modelling approach. Instead, a reasonable and effective combination of different modelling approaches provides solutions to many present and future tasks. The complementary modelling is discussed in detail and illustrated with several case studies.     

A simplified method for modelling the effect of blinds on window thermal performance

An approximate method is presented for predicting the effect of a louvered blind on the centre‐glass thermal performance of a fenestration. The method combines a one‐dimensional heat transfer model with data from a numerical simulation of the window and blind. Sample results for a blind mounted on the indoor surface of a window show the effect of blind slat angle on heat transmission. Both summer and winter conditions are considered. The results show that a louvered blind can improve the U‐value of a standard double‐glazed window by up to 37%. Also, the radiation heat exchange with the room can be dramatically reduced (by up to 60%), which will improve the level of occupant comfort. However, there was found to be a trade‐off between U‐value and occupant comfort; placing the blind closer to the window improves the U‐value, but increases the radiation heat exchange with the room. The predictions from the present simplified method compare well with results from a full two‐dimensional computational fluid dynamics solution of the conjugate blind/window interaction. Copyright © 2005 John Wiley & Sons, Ltd.     

Cost effectiveness of decentralized energy supply systems taking solar and wind utilization plants into account

In this article, results are presented of annual simulations of a decentralized (regional) plant for the power and heat supply of a residential complex. This complex consists of four houses with 40 flats all in all. The annual power consumption of the complex is 157 MWh and the heat requirement is 325 MWh. The concrete dynamics of the energy demands over the year is taken into consideration. The energy supply system is composed of a power-controlled combined heat and power (CHP) plant (55 kW), a photovoltaic plant (PV array or PV plant) array for power generation as well as a field of solar thermal collectors with a short-term accumulator for water heating and a long-term accumulator for supplying heat for domestic heating purposes. Simulation results demonstrate that synergetic effects result from the combination of a CHP plant with wind power and PV plants of varying sizes, which have an effect on the cost effectiveness of the plant as a whole with the different dynamics of energy sources (wind and solar energies) and of the consumption of power and heat being the decisive factors. The power deficits of wind power and PV plants are compensated through the application of a natural gas-operated CHP plant. In almost all variants, the demand for fossil energy carriers is distinctly less than in conventional energy supply plants.     

Present status and future prospects of PV activities in Japan

The photovoltaic (PV) power systems in Japan made great strides in the past decade. The PV industry in the 1990s greatly depended on the research projects and dissemination programs carried out by the Ministry of International Trade and Industry. However, the industrial structure for full-scale deployment of the PV system is currently being established by the manufacturers’ continuous efforts to reduce the PV system cost and the government’s consecutive supports to create the initial market. It is expected that the synergetic effect of the cost reduction and incentives for introduction will activate the PV industry and its market more and more toward achieving 5000 MW of the capacity in FY 2010.     

Wind turbine response to parameter variation of analytic inflow vortices

As larger wind turbines are placed on taller towers, rotors frequently operate in atmospheric conditions that support organized, coherent turbulent structures. It is hypothesized that these structures have a detrimental impact on the blade fatigue life experienced by the wind turbine. These structures are extremely difficult to identify with sophisticated anemometry such as ultrasonic anemometers. This study was performed to identify the vortex characteristics that contribute to high‐amplitude cyclic blade loads, assuming that these vortices exist under certain atmospheric conditions. This study does not attempt to demonstrate the existence of these coherent turbulent structures. In order to ascertain the idealized worst‐case scenario for vortical inflow structures impinging on a wind turbine rotor, we created a simple, analytic vortex model. The Rankine vortex model assumes that the vortex core undergoes solid body rotation to avoid a singularity at the vortex centre and is surrounded by a two‐dimensional potential flow field. Using the wind turbine as a sensor and the FAST wind turbine dynamics code with limited degrees of freedom, we determined the aerodynamic loads imparted to the wind turbine by the vortex structure. We varied the size, strength, rotational direction, plane of rotation, and location of the vortex over a wide range of operating parameters. We identified the vortex conformation with the most significant effect on the blade root bending moment cyclic amplitude. Vortices with radii on the scale of the rotor diameter or smaller caused blade root bending moment cyclic amplitudes that contribute to high damage density. The rotational orientation, clockwise or counter‐clockwise, produces little difference in the bending moment response. Vortices in the XZ plane produce bending moment amplitudes significantly greater than vortices in the YZ plane. Published in 2005 by John Wiley & Sons, Ltd.