Characterization of conducting poly(3‐methylthiophene) films prepared under sono‐electrochemical conditions

Poly(3‐methlthiophene) films were prepared under “silent” and “sono‐electrochemical” potentiostatic (SEP) conditions. A three‐electrode one‐compartment sono‐cell was used with a working platinum disc electrode. The sono‐electrochemically formed polymer films were deposited with different working electrode‐to‐horn distances. The composition, electrochemical, spectroscopic, and morphological characteristics of the resulting polymer films were determined. Elemental analysis, FTIR‐spectra, and X‐ray photoelectron spectroscopy (XPS) data proved that the polymer films prepared under SEP conditions have predominant α‐α′‐couplings between the 3MT units, and the aromatic ring integrity is maintained in the film. Scanning electron microscopy showed that those films are more compact and less porous compared to the films prepared under silent conditions. The use of sono‐irradiation during electropolymerization enhanced the diffusion of the monomer units towards the electrode surface and resulted in relatively less doped polymers with less conductivity. Electrochemical impedance spectroscopy (EIS) data for films prepared under silent and SEP conditions were collected in a monomer‐free solution. The results show that the impedance of SEP films is relatively higher than those prepared under silent conditions, and a combination of charge transfer kinetics with diffusion‐controlled conduction mechanism within the films. The diffusion was found to be a function of the porosity of the film. Conductivity measurements are in good agreement with EIS, elemental analysis, and XPS data. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 2416–2425, 2006     

A_1-A_2-O-M工艺处理焦化废水的实验研究

采用厌氧-缺氧-好氧-复合(A1-A2-O-M)工艺处理焦化废水,考察了外加碳源和碱源对焦化废水COD和NH4+-N脱除效果的影响。试验结果表明:外加甲醇和碳酸氢钠对焦化废水的硝化和反硝化效果影响很小;不外加碳源和碱源时,焦化废水经处理后出水的COD和NH4+-N平均质量浓度分别为125.0mg/L和1.12mg/L,分别达到《污水综合排放标准》(GB8978-1996)中的二级标准和一级标准。     

Efficient material design for diesel particulate filters

This paper will give an overview about the filter development for diesel particulate emission control in automotive applications. The material development for passenger car diesel particulate filters led to new materials like silicon carbide while for heavy duty applications still Cordierite plays a major role. But in the future other materials might also be used for passenger cars. This paper will show the basic difference between both applications and describe the material design in terms of filter properties (base material, back pressure aspects, filtration efficiency, coating impact). Current application on vehicles with catalysed soot filters (CSF) with and without oxidation catalyst will be presented. Furthermore an outlook will be given on materials for catalysed soot filters for the future.     

Crystallization behavior of dry‐brush PEO‐PS block copolymer and PEO homopolymer blend

The crystallization behavior of semicrystalline PEO homopolymer/triblock PS‐PEO‐PS copolymer blend system, which exhibited “Dry‐Brush” in the melt. A symmetric polystyrene–poly(ethylene oxide)–polystyrene triblock copolymer was blended with PEO homopolymer (h‐PEO) having the same molecular weight as that of the PEO block in the copolymer. Considering the composition of the blend (W_ps ≥ 0.8), PEO spheres were formed in the blend. Because of the dry‐brush phase behavior of this blend, h‐PEO added was localized in the PEO microdomains, which increases the domain size without changing the microdomain morphology. The crystallization of PEO block was confined within the microdomains and the crystallization temperature was about 60°C lower than normal. Self‐seeding tests were performed to clarify the nucleation mechanism of the blend. Because the droplets size varies greatly, multicrystallization peaks were witnessed in the self‐seeding process. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Water sorption of poly(vinyl alcohol)/ poly(diallyldimethylammonium chloride) interpenetrating polymer network hydrogels

Temperature‐responsive interpenetrating polymer network (IPN) hydrogels constructed with poly(vinyl alcohol) and poly(diallyldimethylammonium chloride) using the sequential IPN method were studied. The characteristics of IPN hydrogels were investigated using the dynamic vapor sorption system. IPN hydrogels exhibited a relatively high sorption ratio, 180–360% at room temperature. The sorption ratio of hydrogels depended on temperature. Diffusion coefficients were calculated according to the Fickian Law at several temperatures. The apparent activation energy was 5.43 kJ mol^?1, which corresponds to typical diffusion processes. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1389–1392, 2003     

Single frame correction of motion artifacts in PMD-based time of flight cameras

One of the leading time of flight imaging technologies for depth sensing is based on Photonic Mixer Devices (PMD). In PMD sensors each pixel samples the correlation between emitted and received light signals. Current PMD cameras compute eight correlation samples per pixel in four sequential stages to obtain depth with invariance to signal amplitude and offset variations. With motion, PMD pixels capture different depths at each stage. As a result, correlation samples are not coherent with a single depth, producing artifacts. We propose to detect and remove motion artifacts from a single frame taken by a PMD camera. The algorithm we propose is very fast, simple and can be easily included in camera hardware. We recover depth of each pixel by exploiting consistency of the correlation samples and local neighbors of the pixel. In addition, our method obtains the motion flow of occluding contours in the image from a single frame. The system has been validated in real scenes using a commercial low-cost PMD camera and high speed dynamics. In all cases our method produces accurate results and it highly reduces motion artifacts.     

Determinants of users’ continuance of social networking sites: A self-regulation perspective

Social networking sites (SNS) have transformed how individuals interact, build and maintain social relationships. We proposed a research model on the determinants of user continuance using Bagozzi's framework of self-regulation as the theoretical foundation. Following the process of appraisal → emotional reactions → coping responses, we developed the model by leveraging findings from social presence and IS continuance research. Based on survey data from Facebook users, we found that appraisal factors (pleasure, awareness, connectedness, and system quality) were strong determinants of emotional reaction (user satisfaction and sense of belonging). User satisfaction and sense of belonging together positively influenced continuance intention.     

Paving the way for CRM success: The mediating role of knowledge management and organizational commitment

Customer relationship management (CRM) has become one of the most influential technologies in the world, and companies are increasingly implementing it to create value. However, despite significant investment in CRM technology infrastructure, empirical research offers inconsistent support for its positive impact on performance. This study develops and tests a research model analyzing the process through which CRM technology infrastructure translates into organizational performance, drawing on the resource-based view (RBV) and the knowledge-based view (KBV) of the firm. Based on an international sample of 125 hotels, the results suggest that organizational commitment and knowledge management fully mediate this process.