烟气轮机叶片应力分析与寿命评估方法评述

烟气轮机是炼油厂催化裂化装置的关键设备,合理预测叶片疲劳寿命是保障烟机安全运行的有效手段。从力学建模和边界条件两个方面简要阐述了叶片的应力分析方法,并系统分析了影响烟机叶片疲劳寿命的主要因素,提出了利用改进的局部应力应变法进行叶片寿命预测的合理性和叶片疲劳寿命的评估方法。     

双转向垂向控缝技术实验研究及现场应用

针对压裂过程中缝高较难控制的问题，研制开发出新型的油溶性垂向双转向剂，并开展了室内实验研究。首次验证了转向剂对裂缝延伸的控制机理，确定了转向剂的适用浓度及控缝能力。实验表明，转向剂可以增加隔层应力3～4MPa左右。在此基础上研究了控制裂缝高度施工方案的设计方法，并利用全三维软件结合垂向应力剖面对控缝技术进行了优化。现场推广应用30井次，取得了较好的控缝效果。     

淤泥软基爆炸固结试验研究

对爆炸效应在淤泥软基工程中的应用问题进行了探讨，并首次提出了爆炸在淤泥软基中的分界应力特征以及排水固结及破坏分区的基本模式。为采用动力加速对淤泥软基工程的处理，提供了试验依据，具有实用价值和指导意义。     

A concept for the generation of out-of-plane distortion from tailored FRP laminates

The phenomenon of thermally induced distortions in unsymmetrical laminates is well understood, and it may be shown that a square, unsymmetrical 0.90 laminate will tend to form two stable geometries with a snap-through phenomenon between them. This paper discusses laminates in which at each point the lay-up is symmetrical across the laminate mid-plane, but which still exhibit multiple stable geometries. The number of stable geometries can be controlled by the details of the lay-up from the minimum of two to, in principle, an unlimited number. In addition it will be shown how a similar process can be used to generate multiple stable stress states and geometries in unidirectional laminates. This paper represents a very preliminary experimental investigation of the design space available for such composite laminates. Possible applications of composites with multiple stable geometries are noted.     

Modeling of Material Deformation Kinetics in the Prefracture Zone

Based on the concept of complete stress–strain diagrams, we propose a new model describing the law of stress distribution in the prefracture zone in plastic materials in view of the type of the stressed state.     

高压对气井套管接头螺纹接触应力的影响研究

高温高压气井对螺纹密封性的要求要比油井更为严格。对于高压气井中的整个管柱,每一段处于不同的力学环境中,发生泄漏的可能性也不同,因此研究压力对气井套管接头螺纹接触应力的影响,对高压气井套管的合理使用尤为重要。利用弹塑性有限元分析方法,建立了API偏梯型螺纹套管接头的有限元模型,分析了气井压力对套管接头接触应力的影响,提供了研究压力对套管接头螺纹接触应力影响的方法。对于井口压力或井底压力超过34MPa的高压气井,应选用气密性良好的特殊螺纹接头,建议采用金属对金属的螺纹接头套管,以加强螺纹部位的连接强度和密封性能。     

起升中四腿落地式K型井架及底座的应力分析

针对在用四腿落地式K型井架在起升中井架与底座存在的问题,文章以JJ162/42-K型井架为例,采用I-DEAS有限元软件对起升过程中处于各角度时的井架及底座做了应力分析,并将其结果与两腿落地式K型井架进行了比较。分析表明,四腿落地式K型井架及底座在井架刚起升时,应力值较大,存在安全隐患。为了增强在井架起升过程中底座的安全性,建议在底座上井架2个铰支座之间加焊加强钢板,并加大井架前立柱铰支座的尺寸。     

Finite element piezothermoelasticity analysis and the active control of FGM plates with integrated piezoelectric sensors and actuators

 An efficient finite element model is presented for the static and dynamic piezothermoelastic analysis and control of FGM plates under temperature gradient environments using integrated piezoelectric sensor/actuator layers. The properties of an FGM plate are functionally graded in the thickness direction according to a volume fraction power law distribution. A constant displacement-cum-velocity feedback control algorithm that couples the direct and inverse piezoelectric effects is applied to provide active feedback control of the integrated FGM plate in a closed loop system. Numerical results for the static and dynamic control are presented for the FGM plate, which consists of zirconia and aluminum. The effects of the constituent volume fractions and the influence of feedback control gain on the static and dynamic responses of the FGM plates are examined. Received: 13 March 2002 / Accepted: 5 March 2003 The work described in this paper was supported by a grant awarded by the Research Grants Council of the Hong Kong Special Administrative Region, China (Project No. CityU 1024/01E).     

The influence of plastic properties on chip formation

A two-dimensional finite-element model of the chip formation process is used to study the influence of the material law determining plastic flow on chip formation of titanium alloys at high cutting speeds. For simplicity, friction and thermo-mechanical properties of the tool are neglected in the simulations. Titanium chips are strongly segmented and therefore especially suitable to study the role of segmentation for the cutting force and other cutting parameters. Of special interest is the influence of the thermal softening parameter in the material law. Increasing thermal softening leads to a drastic decrease in the cutting force and a corresponding increase in chip segmentation. A variation of the hardening exponent is also performed. It is shown that the simulation results can be understood by using adiabatic flow stress curves. The variation of the hardening exponent leads to strongly differing chip shapes, although the cutting force stays nearly constant. This shows that mean cutting forces should not be used as simulation verification parameters.