Schwingfestigkeit von Schraube‐Mutter‐Verbindungen

High cycle fatigue of bolted connections Extensive tests regarding the influences on the fatigue of bolt‐nut‐connections of preloading with torsion, of preloading with yielding, of loading with superimposed bending and of the tested lot are processed. These influences are not yet known according to VDI 2230. New testing devices were designed for these tests, which allow a far less expensive operation and may easily be used for bolts of diameters up to M100 and testing frequencies up to 1000 Hz. The validity of fatigue resistance according to VDI 2230 is specified with respect to the test results. The determined influence of the tested lots is unexpectedly high. The manufacturing process of bolts should be improved to minimize this influence.     

Express Method for Estimation of Tensile Strength and Crack Resistance of Brittle Media

The procedure is proposed for estimating the crack resistance and tensile strength of rocks by the results of experiments on disk samples with holes. The gradient approach to the strength problem is employed in processing the experimental data.     

Determination of shear strength values according to EN 408

This paper presents the results of 382 shear tests carried out according to EN 408. The test pieces consisted of spruce (Picea abies) and varied in density and ring width orientation (radial, tangential and at an angle of 45° to the steel plates). In addition pieces containing pith and knots were tested. The paper discusses problems observed when using this test configuration and shows that the test results do not support the characteristic shear strength values as given in EN 338. Moreover, the test results do not support the relationship between characteristic shear strength and characteristic bending strength as given in EN 384.

---

Résumé Cet article présente les résultats de 382 essais de cisaillement menés conformément à EN 408. Les éprouvettes d’essai sont en épicéa (Picea abies) et présentent une variabilité en termes de masse volumique et d’orientation des cernes d’accroissement (radiale, tangentielle, à un angle de 45° par rapport aux plaques métalliques). Des éprouvettes supplémentaires contenant du cœur et des nœuds ont également été testées. L’article évoque les problèmes qui ont été mis en évidence lors de l’utilisation de ce dispositif expérimental et montre que les résultats expérimentaux ne sont pas en accord avec les valeurs caractéristiques de résistance au cisaillement données dans EN 338. De plus, ces résultats ne confirment pas la relation entre résistance caractéristique au cisaillement et résistance caractéristique à la flexion telle que stipulée dans EN 384.

     

利用先进的结构试验系统进行发动机构件的仿真疲劳试验

本文介绍一套先进的构件实验设备的功能及其在发动机构件疲劳试验方面的具体应用实例．通过对几种受力较复杂构件的受力分析设计出实验方法，使构件在实验室中受力情况与构件实际受力情况相似或相同，这样，得出的试验数据就可为构件的可靠性分析工作提供较好的依据．     

Pullout tests of epoxy-coated reinforcement in concrete

The bond strength and slip of epoxy-coated reinforcing bars in concrete have been evaluated by carrying out single pullout and double pullout tests. In extended single pullout tests, slip measurements were made while tensile force was applied to reinforcing bars embedded in concrete. In double pullout tests, 20 cycles of load were applied at levels of steel stress between zero and 0·5 times characteristic steel strength. Strains were measured by electrical resistance strain gauges glued inside the bars. Both epoxy-coated and uncoated bars were used in the investigation, to obtain comparative results. The strain gradient along the bar was found to be less for the coated reinforcement. In general, the epoxy coating was found to increase slip in bond and thereby reduce the bond performance of coated bars.     

结构陶瓷的高温疲劳强度衰减理论

提出了陶瓷材料疲劳强度衰减理论并由此导出了各种疲劳关系式。建立了疲劳基本方程ｄσ＿ｒ／ｄ＿ｉ＝一Ａσ（ｔ）￣ｎｔ￣（－ｍ），得出了疲劳寿命公式Ｔ＝Ｍ（σ＿０－σ）／Ａσ￣ｎ（静疲劳时Ｍ＝１，连续增载疲劳时Ｍ＝ｎ＋１，循环疲劳时Ｍ＝（ｎ＋１）／（１＋Ｒ＋Ｒ￣２＋……＋Ｒ￣ｎ），逐级加载时，并导出不同疲劳方式下疲劳寿命间的关系。同时，用多种Ｓｉ＿３Ｎ＿４材料在高温中作了论证试验，结果与理论一致。     

Reticulated Porous Multiphase Ceramics with Improved Compressive Strength and Fracture Toughness

A multiphase reticulated porous ceramic (RPC) as Si₃N₄–Al₂O₃–SiO₂ was fabricated by replication techniques. Proper volumes of additives and twice sinter- twice immerse process endow the RPC an excellent crack healing and submerging property. The compressive strength and fracture toughness improved owing to the crack bridging behavior. The existence of pores in struts in RPC blunt the crack tip and increased the external force needed to propagate the crack. The mechanisms play a beneficial role in enhancing the compressive strength and fracture strength. Si₃N₄ RPC with additives of 5%Al and 5% Al₂O₃ yielded the compressive strength of 9.8 MPa and fracture toughness of 0.3 MPa m^1/2.     

Strength of Metals at High Strain Rates

Results of metal testing in impact tension–compression and indentation are analyzed. As the analysis of these data demonstrates, the strength of metals increases greatly with strain rates and at moderate indentation rates. At high indentation rates, a decrease in the specific energy (per unit volume of a displaced material) necessary for the formation of a conical cavity was observed. The account of the effects of viscosity, temperature increase upon plastic deformation and its localization can be used to explain the above phenomena.     

弹药包装冲击强度试验方法的改进研究

介绍一种新的弹药包装冲击强度试验方法，应用该试验方法可以防止冲击强度试验时出现与期望值相反的现象。     

The concept of an endurance limit for adhesive joints

The effect of cyclic stressing on the strength of single lap adhesive joints has been studied and a considerable reduction in strength observed when the maximum stress exceeds about 40% of the ultimate tensile strength, but whether or not a true endurance limit exists is not proven. Fallacies are shown in some of the techniques which have been proposed for studying the fatigue behaviour of adhesive joints.