Corrosion fatigue of extruded magnesium alloys

Corrosion fatigue tests were carried out on extruded AZ31 (3% Al, 1% Zn, 0.3% Mn, Mg—the rest), AM50 (5% Al, 0.4% Mn, Mg—the rest) and ZK60 (5% Zn, 0.5% Zr, Mg—the rest) Mg alloys in air, NaCl-based and borate solutions. N_sol/N_air ratios (the relative fatigue life) were used for the analysis of the corrosion fatigue behavior of Mg alloys in various environments, where N_sol and N_air are the numbers of cycles to failure in the solution and in air, respectively. Extruded ZK60 alloy reveals very high fatigue and corrosion fatigue properties in comparison with other alloys. However, it has the lowest relative fatigue life (N_sol/N_air 10⁻³–10⁻²) or the highest sensitivity to the action of NaCl-based solutions in comparison with that of AM50 and AZ31 alloys (N_sol/N_air 10⁻²–10⁻¹). Under the same stress, the corrosion fatigue life of extruded alloys is significantly longer than that of die-cast alloys (N_sol for extruded AM50 in NaCl is two to three times longer than that of die-cast AM50).     

Influence of fretting on the fatigue strength at the vise clamp-specimen interface

Fretting fatigue is one of the most important phenomena for inducing a significant reduction of fatigue strength and consequently, leading to unexpected failure accidents of the engineering structures even at very low stresses. In the present study, both plain and fretting fatigue tests with zero mean stress were carried out on two different types of steel, low-carbon steel and martensitic stainless steel, by means of a reversed bending fatigue testing machine. The drop in the fatigue strengths through fretting at vise clamp-specimen interface were significant for both tested steels. The fretting processes produced a reduction in fatigue strength of about 27% for low-carbon steel and 16% for martensitic stainless steel.     

A time series approach to fatigue crack propagation

The inherently nonlinear phenomenon of fatigue crack propagation is modeled as a linear random process. To a first approximation, simple, nonstationary time series models are introduced and standard techniques for determining the parameters of autoregressive integrated moving-average processes are applied. Multiplicative time series models are next utilised for the representation of a group of crack history curves. Implementation of the models on the Virkler experimental data set yields satisfactory results. Reliable Gaussian approximations to the distribution of the time required by a crack to reach a specified critical length are obtained, and the usefulness of the approach is demonstrated when updating lifetime predictions after periodic inspections.     

Temperature–stress–strain trajectory modelling during thermo-mechanical fatigue

The isothermal strain‐life approach is the most commonly used approach for determining fatigue damage, particularly when yielding occurs. Computationally it is extremely fast and generally requires elastic finite element analyses only. Therefore, it has been adapted for variable temperatures. Local temperature—stress–strain behaviour is modelled with an operator of the Prandtl type. The hysteresis loops are supposed to be stabilized and no creep is considered. The consequences of reversal point filtering are analysed. The approach is finally compared to several thermo‐mechanical fatigue tests and the Skelton model.     

硬度匹配对40CrNiMo滚子接触疲劳性能的影响

通过对“软－软”、“中－软”、“中－中”、“中－硬”四组不同硬度匹配的滚子接触疲劳试验得出四条Ｐ－Ｎ曲线。并发现中硬度材料的接触疲劳寿命高于软材料，而当主试样为中硬时，与之相匹配的陪试件硬度越高，主试样的寿命越短，通过分析讨论解释了产生上述现象的原因及其失效机理。     

Fatigue crack growth analysis of welded aluminium RHS T-joints with manipulated residual stress level

The fatigue life of a welded aluminium T‐joint made from beams with rectangular hollow section (RHS) has been predicted using a crack propagation analysis and compared with experimental results from joints with different residual stress levels. To include the effect of the residual stresses, the stress ratio was calculated at the weld toe and, via Walker's equation, introduced into the analysis. How to obtain the Walker exponent has been discussed in detail. The introduction of a stress ratio at the weld toe provides good agreement between the experimentally and analytically found S–N curves. The effect of the residual stress was successfully included in the analysis.     

Determining the life cycle of bolts using a local approach and the Dang Van criterion

The fatigue behaviour of bolts under axial load has always been considered from the component point of view for which fatigue limit is usually taken equal to 50 MPa, and few results are available to designers for limited lifetimes. Here, we take up this problem from a material point of view using a local approach. For each case of fatigue testing, using finite‐element (FE) model of the bolt, we determine the stabilized local stress at the root of the first thread in contact with the nut. To characterize bolt behaviour with these numerical results, we use Dang Van multiaxial fatigue criterion for which we extend application to the medium fatigue life. These results can be correlated with the experimental numbers of cycles to failure to determine material parameters of the generalized criterion. Using statistical Gauss method, we can make lifetime predictions for any level of risk of failure. In addition, we propose an analytical model to rapidly determine the local stress condition from nominal loading data (mean stress and alternating stress). This model dispenses us from a new modelling if the bolt is stressed in the same manner as the bolts used for behaviour characterization. Using this model and the generalized criterion, it is extremely easy to make lifetime predictions whatever the risk considered.     

Critical incidents and chronic stressors at work: Their impact on forensic doctors.

Workers in medium- or high-risk professions are often confronted with critical incidents at the workplace. The impact of these acute stressors may be serious and enduring. Many workers also experience chronic job stressors, such as work overload or role conflicts. This study examined the frequently neglected relationship of acute and chronic stressors with self-reported health symptoms, such as posttraumatic responses, fatigue, and burnout. This association was investigated in a sample of forensic doctors in the Netherlands (N = 84). It was found that the more traumatic events the respondents experienced, the more problems they reported in coping with the traumatic events. Chronic job stressors were associated with posttraumatic responses (intrusions and avoidances) and with burnout and fatigue. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Finite element simulation of the mechanics of flat contact pad fretting fatigue tests

An understanding into the macro kinetic and kinematic behaviour of fretted surfaces is provided. Making use of a modified version of a previously developed in‐house two‐dimensional elastic–plastic finite element analysis numerically simulates flat contact pad fretting fatigue tests. Basic macro mechanics concepts are adopted to idealise two bodies with rough contact surfaces and loaded at two different sites with arbitrary axial loading profiles. A time scale factor is devised to recognise the earliest candidate out of the events possibly accommodated at each loading increment. The present analysis utilises a relevant experimental set up developed in the Structural Integrity Research Institute of the University of Sheffield as an application. Computational results accurate to within 1.2% and corresponding to one contact pad span and six constant normal loads acting individually with four amplitudes of two sinusoidal axial load cycles are presented. The present computations include (1) the development of the global and local normal and tangential reactions and relative sliding displacement acting along the fretting surfaces and (2) contact pad deformation, generated stress fields and plasticity development within the neighbouring region of the fretted area.     

锅炉未焊透椭圆接管结构应力数值分析

应用有限元法对未焊透的椭圆接管结构进行了应力数值分析,并应用压力容器分析设计法,对该结构进行了疲劳分析,得出结构因未焊透缺陷导致疲劳破坏。