Drying of Prone to Twist Boards in a Pre-Twisted Position

A method to minimize twist has been investigated; i.e., drying the boards in a pre-twisted position. It has been found that Norway spruce boards can be deformed toward straightness by this method. The force exerted by a board on its holders during drying in a pre-twisted position has been measured. When the variation in torsional stiffness as a function of temperature and moisture content is accounted for, it is found that a creep deformation of the board occurs both during the drying phase and the cooling phase. In addition to mechano-sorptive creep, a deformation released by a change in temperature also seems to occur.     

高能超声处理Al-1Si合金凝固组织分析

采用高能超声处理Al-1Si合金熔体,借助金相显微镜和电子探针进行组织分析,并测定合金的熔化潜热,分析了熔体中超声空化效应和声流效应影响凝固过程的机理。结果表明,试样晶粒平均尺寸由超声处理前的94μm减小到超声处理后的34μm;合金试样的熔化吸热量由263.90J/g降低为159.81J/g,在熔体中施加高能超声显著改善了合金成分的均匀性并细化了晶粒。     

Strengths and ductility of Mo–TiC alloys after secondary recrystallization

A series of Mo–TiC alloys were heated in vacuum at 2473 K for 36 ks. First grain growth behavior was observed using a scanning electron microscope. Then effects of TiC addition on the strengths and ductility at low temperature were discussed from the viewpoints of chemical composition and grain structure.

Materials with TiC additions of not larger than 0.1% demonstrated a single-crystalline grain structure. Both yield and maximum strengths increased by TiC addition and consequently ductility was improved.     

水稻强化栽培下不同氮肥管理对产量与氮素利用的影响

以籼型单季超级杂交稻中浙优1号为材料,研究水稻强化栽培氮肥管理对产量与氮素利用率的影响。结果表明:水稻强化栽培与常规栽培对照比较,增产达11.1%-15.2%,氮肥回收率比对照高5.3%~26.9%,农学利用率比对照高67.2%~92.2%,生理利用率比对照高6.0%~80.5%。因此,在水稻生产上应用水稻强化栽培可以提高氮肥的利用,降低氮肥在环境中积累及对环境造成污染。此外,本文对水稻强化栽培下氮肥管理的高产机理进行了探讨。     

CNC机床结构动态设计方法研究

提出机床结构动态设计基本原则。以某数控弧齿铣齿机为研究对象,应用相关的动态设计原则,通过变量化设计与有限元分析,对该机床进行结构动态设计。结果表明,应用该方法设计的机床结构具有良好的动静态特性。     

数控机床交流伺服系统的复合控制研究

针对常规P-P与PPI控制存在的问题，提出了在数控机床交流伺服系统中，采用带速度和加速度作为前馈控制，模糊自校正PID控制作为位置反馈控制的复合控制器，实验证明可以显著提高控制系统的控制精度，大大降低跟踪误差，具有较强的鲁棒性。     

一种用于粮食分装机的电子称重系统

由单片机系统、称重传感器、电磁阀等组成的粮食分装机电子称重系统，具有定量分装、自动去皮、累计量计算、数据实时显示、定标、通讯等功能．采用粗、精两通道送料方式．提高了分装精度。整个系统运行可靠、精确度高。     

AN EXPERIMENTAL INVESTIGATION OF THE GROWTH OF SMALL CORNER FATIGUE CRACKS IN ALUMINIUM 6061-T651

Results of an experimental investigation of the fatigue growth of small corner cracks emanating from small flaws are presented. Growth-arrest behaviour was observed, and increases in crack length during growth periods were of the order of the transverse grain size. For the test material, the corner crack front intersects, on average, only three–six grains in the small crack regime monitored, so only a small number of constrained, interior grains is encountered. It is suggested that the presence of partially constrained surface grains may contribute to the 'anomalous' growth behaviour which has been observed by a number of investigators.
The crack growth histories of the test data presented exhibit considerable scatter. It is shown that a Student's t -test can be used to estimate confidence intervals in order to provide a measure of the observed scatter. The variation in confidence intervals in the transition from small to long fatigue crack growth is discussed.     

从萨沃伊别墅探究勒·柯布西耶的机器美学

文章论述了萨沃伊别墅的机器美学思想,主要结合了勒·柯布西耶在1926年提出的"建筑新五点"来探讨他所主张的机器美学在萨沃伊别墅上是如何得以实现。     

台达机电产品在高速集束球经机中的应用

本文主要介绍台达20PM运动控制器在纺织行业的高速集束球经机中的应用。阐述了球经机的技术特点和工艺要求,简介了控制系统的硬件配置和应用程序。在控制系统中利用20PM内置的多组电子凸轮功能实现了两边成型和精密绕排等各项工艺目标。