Tribological behavior of PTFE nanocomposite films reinforced with carbon nanoparticles

Carbon-based nanoparticles synthesized by heat treatment of nanodiamond in the temperature range of 1000–1900 °C were added to PTFE film to investigate the structural effect of the carbon particles on the tribological properties of PTFE composite film. Carbon-based nanoparticles were prepared by milling with micron sized beads in chemically treated water before their addition to PTFE film. The wear and frictional properties of PTFE nanocomposite film were measured by the ball on plate type wear test. The wear resistance of PTFE film was found to be enhanced by the addition of 2 wt% of carbon nanoparticles. The wear coefficient of PTFE film was decreased from 16.2 to 3.5 × 10⁻⁶ mm³/N m by the addition of carbon-based nanoparticles heat-treated at 1000 °C. Increasing the heating temperature of the nanodiamonds caused the extent of aggregation and particle size to increase. The wear resistance of PTFE nanocomposite film was enhanced by the addition of nanodiamonds heat-treated at 1000 °C, but decreased when the heat treatment temperature of carbon nanoparticles was further increased. Tribological behavior of PTFE nanocomposite films depending on the types of carbon nanoparticles were explained based on the structural, physical and chemical modification of carbon nanoparticles.     

Pulsating Jet Impingement Heat Transfer Enhancement

This article presents results from a numerical study of pulsating jet impingement heat transfer. The motivation is to seek conditions offering a significant enhancement compared to steady flow impingement drying. The CFD software package FLUENT was used for simulating slot-type pulsating jet impingement flows with confinement. The parameter study included velocity amplitude ratio, mean jet velocity, and pulsation frequency. The distance from nozzle exit to surface was three times the hydraulic diameter of the nozzle. The Reynolds number based on the nozzle hydraulic diameter and jet temperature was 2,460 with a mean jet velocity of 30 m/s, which is the base case of the numerical experiments. Results showed that time-averaged surface heat transfer increased with increasing velocity amplitude for the same mean jet velocity. Large velocity amplitudes helped enhance heat transfer by two mechanisms: high jet velocity during the positive cycle and strong recirculating flows during the negative cycle. For the cases with different mean jet velocities but the same maximum velocity, time-averaged surface heat flux decreased with decreasing mean jet velocity. As for the effects of pulsation frequency, with high-velocity amplitude ratio, time-averaged surface heat fluxes were at the same level regardless of frequency. However, at low-velocity amplitude ratio, high frequency caused stronger recirculating flows resulting in greater heat transfer compared to the cases with a lower frequency.     

二高炉4号热风炉烘炉实践

介绍了二高炉4号热风炉烘炉的特点、前期准备工作、具体操作过程中的注意事项及烘炉后的相关作业。此次生产实践对今后类似情况的热风炉烘炉具有参考价值。     

Convective cooling of supercritical carbon dioxide inside tubes: heat transfer analysis through neural networks

In a previous work, convective heating of carbon dioxide was studied with neural networks (NN), obtaining a totally heuristical heat transfer equation from the direct regression of experimental data. In the present work, the analysis focuses on the cooling process, which has a technical relevance in various applications, as for example in transcritical refrigeration cycles. Heat transfer around the critical zone presents a marked enhancement, that follows the peaks in thermophysical properties like thermal conductivity and heat capacity. Similarly, other properties like density and enthalpy, present a strong variation in narrow temperature intervals around the critical point.This constitutes then a highly non-linear phenomenon, for which it is advisable to use a very flexible function approximator like the NNs. NN models were applied both in terms of dimensionless numbers and of physical quantities, obtaining the two corresponding NN architectures. The choice of the optimal number of neurons in the NN hidden layer is discussed. The NN models are then compared with a recent correlation from literature, for which the validation results present an AAD of 27% and a bias of −26% with an evident prediction shifting. On the other hand the NN models in terms of dimensionless numbers and of physical quantities have AAD and bias of 14% and −4%, and of 7% and −2%, respectively, showing a largely better performance.     

纯棉热转移印花色光稳定性的研究

以分散蓝291热转移印花的纯棉织物为例，考察环境诸因素对其色光稳定性的影响，并结合色度参数和XPS谱图分析环境各因素对色光稳定性的影响机制。     

Composite scale modeling in the presence of censored data

A composite scale modeling approach can be used to combine several scales or variables into a single scale or variable. A typical application is to combine age and usage together to form a composite timescale model. The combined scale is expected to have better failure prediction capability than individual scales. Two typical models are the linear and multiplicative models. Their parameters are determined by minimizing the sample coefficient of variation of the composite scale. The minimum coefficient of variation is hard to apply in the presence of censored data. Another open issue is how to identify key variables when a number of variables are combined. This paper develops methods to handle these two issues. A numerical example is also included to illustrate the proposed methods.     

改造加热炉系统 提高加热炉热效率

分析了重整装置加热炉热效率低的原因，介绍了提高加热炉热效率采取的几项措施。     

Kinetics of TSCD zinc oxide nano-layer growth by modified diffuse-interface model

Deposition of zinc oxide films from aqueous solutions containing complex Zn²⁺ ions on soda-lime substrates were studied by two-stage chemical deposition (TSCD) process. It was shown that the film thickness can be controlled by the number of dipping stages. Nano-layers were produced with less than nine times dipping stages. Greater dipping numbers resulted in film thickness exceeding 100 nm. The growth rate obeyed double-stage zeroth order with respect to the concentration and first order with respect to the temperature. This rate was proportional to the difference between the temperature of the hot water and the substrate. Overall activation energy of 17.20 ± 0.42 kJ mol⁻¹ and frequency factor of 2.81 ± 0.07 μm s⁻¹ was determined for ZnO deposition. These values were attributed to two resistances. One resistance corresponded with film heat transfer mechanism. The other was attributed to species attachment to the solid substrate. A modification to the diffuse-interface kinetic model was devised for explanation of the latter. EDAX (electron dispersive elemental analysis), XRD (X-ray diffraction) and SEM (scanning electron microscopy) were used to characterize the layer formed. These methods showed that the product consisted solely of pure elliptical ZnO grains.     

Potential of ground heat source systems

This paper presents a historical background of ground source heat pump technology, followed by a review of its current shortcomings. Based on these observations the author assesses the R&D needs and recommendations for future research.     

Heat evolution of high-volume fly ash concrete

In this paper, the results of a laboratory investigation conducted with heat evolution of high-volume fly ash (HVFA) concrete are presented. Heat evolution of concrete was studied by measuring the temperature increase in concrete under adiabatic curing condition. Characteristic of heat evolution of fly ash concrete was found to be strongly dependent on the replacement level of fly ash and dosage of superplasticizer used to maintain workability. It was also found that using fly ash as cement replacement resulted in a reduction on the maximum temperature rise. Increasing the replacement level of fly ash caused lower temperature rise in concrete. Superplasticizer caused a delay in peak temperature rise time; this is taken as an indicator that high-dosage superplasticizer used in concrete caused retardation in hydration of cement. Concretes having similar ingredients showed similar peak temperature rise whether they are superplasticized or not.