This study develops a mathematical model for coupled heat and mass transfer in an unsaturated porous slab exposed to a flowing hot gas. Effects of the initial saturation conditions on associated variables, i.e., total pressure, temperature, moisture content, and multiphase flow, are studied. The Newton-Raphson method based on a finite volume technique is applied. This study emphasizes the influence of initial saturation level and gravitational effect in heat and multiphase flow phenomena associated with this system. Gravity enhances the downward flow of liquid within the porous slab. Pressure buildup occurs near the interface between the wet and the dry zone. However, it appears that the order of magnitude to the total pressure is small. This study explains the fundamental mechanism of multiphase flow that involves heat and mass transfer in a heated unsaturated porous slab. 相似文献
London Resin (LR) White is a commonly used resin for embedding specimens to be used for immuno- and/or cytochemical studies. In some instances, due to either the properties of the specimen or the availability of various reagents and equipment, it becomes necessary and/or more convenient to polymerize LR White using heat rather than chemical accelerators or UV light. It is known, however, that heat can reduce or even eliminate the anti genicity of the tissue being embedded. It is therefore desirable to polymerize specimens at the lowest temperature possible and to remove the specimens from the oven as soon as polymerization is complete. We have developed a technique that provides a visual marker that allows the exothermic polymerization of LR White to be monitored, thus minimizing the amount of time a specimen must stay in the oven while excluding oxygen from capsules of polymerizing LR White. 相似文献
The white organic light emitting device (OLED) with single-structure using a polymer blend as the light emitting layer is fabricated. Heat treatment is used to control the ratio between the intensities of main electroluminescent spectral peaks. The electroluminescent spectrum of our device is quite similar to that of white inorganic LED produced by Nichia Corporation after being annealed, and its turn-on voltage can be decreased by 1V. 相似文献
An ice slurry generation system was developed using direct contact heat transfer between water and the coolant, Fluroinert FC-84. The location of the coolant nozzle is an important design consideration to avoid clogging due to freezing of water. An ice fraction of up to about 40 percent was obtained with the nozzle located at the bottom of the ice slurry tank and the jet directed upwards into the water. Two simplified model were developed to extract the heat transfer coefficient between the coolant drops and the water. The first model requires as input the average drop diameter and the residence time while the second model uses the measured drop diameter distribution. The estimated heat transfer coefficients are much smaller than those computed using single-sphere correlations. 相似文献
Home storage is the final step of the frozen foods distribution chain, and little is known on how it affects the products quality. The present research describes frozen green beans (Phaseolus vulgaris, L.) quality retention profile during the recommended ‘star marking’ system dates, at the storage temperatures of +5, −6, −12 and −18 °C (along 1, 4, 14 and 60 days, respectively).
The quality profile was assessed by a simulation system. Simulations were set by a response surface methodology to access the effect of different packaging materials (thermal conductivities and thickness), surface heat transfer coefficient, and refrigerator dynamics (effect of refrigeration cycles at the different storage temperatures) on the average retentions of Ascorbic Acid, total vitamin C, colour and flavour.
Green beans quality losses along frozen storage are significantly influenced by temperature, refrigerator dynamics and kinetic properties. Quality is also highly dependent on packaging materials thermal insulation (e.g. at temperatures above the melting point). Temperature cycles inside frozen chambers have a long term effect, and at the higher storage temperatures (e.g. T>−6 °C) are detrimental to frozen green beans quality after shorter periods. 相似文献
Analysis on steady-state and transient heat transfer on a flat plate at the middle of a parallel duct immersed in He II was performed for bath temperatures from 1.8 to 2.1 K at 101.3 kPa. Two-dimensional computer code named SUPER-2D developed by the authors based on the two-fluid model and the theory of mutual friction was used. Steady-state critical heat flux (CHF) and the time lag from the application of a step heat input to λ transition, that is called a lifetime, were obtained numerically for various step heat fluxes and for the channel gaps from 2 to 20 mm. Effect of the gap restriction on the CHF and the lifetime were clarified. The solutions were compared with the experimental data for the ducts with the same structures and the corresponding conditions. They agreed well with the experimental data. The heat transport mechanism in the parallel duct was clarified. 相似文献
This article presents the development of a ceramic micro heat exchanger. Starting from its geometrical design, results obtained from a simplified simulation of the heat exchanger efficiency will be given. The alumina microcomponents were manufactured by a rapid prototyping process chain. Here, stereolithography was combined with a low‐pressure injection molding process for the rapid and precise manufacturing of ceramic components down to the micrometer range. A micro heat exchanger, joined from sintered components using a glass solder, was applied as a prototype and checked for its performance at a system pressure of 8 bar. 相似文献
This paper presents a new computerized procedure for dealing with the design of horizontal ground heat exchangers (HGHE). The computer program is based on the transient model of coupled nonlinear partial differential equations governing heat and mass flow in soils. The model is two-dimensional and delineates the operation of ground heat storage with the HGHE and such phenomena as freezing/thawing and drying/rewetting of soil moisture. Comprehensive climatological data, such as ambient temperature, solar radiation, wind velocity, rainfall, snowfall, snow characterstics, and water vapour pressure is used to simulate conditions at the ground surface over any required length of time. The package can be applied to any geographical location by changing climatic and soil data input. The designer has the possibility of selecting any of 12 types of soils from sand to clay, 12 commercial heat pumps, nine different configurations of the HGHE, 16 plastic pipes for ground coils, and 13 ground coil fluids. The program, however, does not calculate the length of the HGHE but it evaluates the thermodynamic performance of a ground heat pump system and provides comprehensive data on thermal and hydraulic conditions in ground heat storage. The length of the ground heat exchanger is obtained from a line source theory model or from site dimensions and pipe spacing. Computed results for ground heat exchanger operation correlate fairly well with experimental data. Simulation of temperature and moisture content in the ground for natural conditions (no heat extraction/deposition) showed a fair agreement with field data. The entire computer program is user-friendly, interactive, menu-driven, and written in FORTRAN 77. 相似文献