HB-3、HB-4型钴钼触媒升温硫化总结

总结了HB - 3,HB - 4型钴钼触媒升温硫化过程及注意事项 ,简单介绍了使用情况 ,并针对出现的问题采取了一定措施     

HART通信协议在汽油机速度测量和监控方面的应用

首先介绍了HART通信协议及他的优点，然后介绍了HART通信协议在汽油机测速方面的软件实现。该软件主要采用目前流行的VB编程语言。可设计出界面友好、功能强大的测量和监控软件。     

新型的芯片间互连用CMOS/BiCMOS驱动器

从改善不同类型 IC芯片之间的电平匹配和驱动能力出发 ,设计了几例芯片间接口 (互连 )用 CMOS/Bi CMOS驱动电路 ,并提出了采用 0 .5 μm Bi CMOS工艺 ,制备所设计驱动器的技术要点和元器件参数。实验结果表明所设计驱动器既具有双极型电路快速、大电流驱动能力的特点 ,又具备 CMOS电路低压、低功耗的长处 ,因而它们特别适用于低电源电压、低功耗高速数字通信电路和信息处理系统。     

试油井产量折算新方法

为了使试油折算产量的条件尽可能的相同,增强试油产量的可比性,消除地面计量的人为误差,研究了试油求产时井底流压的变化规律,认为采用油柱在油管内上升的流压变化速率来折算产量更趋于合理,并能最大限度地接近地层真实产量.该方法从根本上消除了因试油周期选定不合理、地面计量误差,以及试油工艺不同、储层条件差异带来的试油产量误差.     

N-苄基丙烯酰胺的合成

以丙烯腈和苯甲醇为原料，浓硫酸作催化剂，合成了N-苄基丙烯酰胺（N-BAA）。考察了反应温度、反应时间和催化剂用量等因素对产物收率的影响，得出了最佳反应条件：n（丙烯腈）：n（苯甲醇）：n（浓硫酸）=3：1：1．2，反应时间3h，反应温度60℃。在最佳条件下，N-BAA的收率可达92％。每100g粗产物用10％氢氧化钠溶液提纯，精制产物纯度可达99．80％，熔点为64～65℃。通过红外光谱对产物结构进行了表征。     

一种新的主动网络安全体系的设计

尽管主动网络原型系统中设计了一些安全措施，但是它们都不具通用性且主要集中在security方面，这在主动网络必须和传统网络相兼容的情况下，阻碍了主动网络的发展。本文在定义消极型错误和积极型错误的基础上，设计了主动网络资源控制核。然后提出了集security和safety保障为一体的基于资源控制核的一种通用的主动网络安全体系，探讨了该体系应具有的特点、设计目标和可行性，并设计了主动节点的安全机制。     

Magnetic Properties of Fe-Doped Rutile

Ball-milling method was applied to dissolve Fe into titanium dioxide (TiO₂). X-ray diffraction indicated the starting anatase changed to a rutile-type structure with oxygen deficiency after ball milling. Transmission electron microscopy and X-ray absorption experiments were conducted to examine the possible existence of magnetic impurities in the ball-milled powders after they were leached in HCl solutions. Temperature dependence of the resistivity shows semiconducting behavior and the magnetic hysteresis loops at 5 and 300 K exhibit ferromagnetic characteristics. Fe-doped TiO₂ films were also prepared by pulsed laser deposition. The magnetic properties of the films are discussed.     

CMOS光接收机主放大器设计

利用CMOS工艺设计一种用于SDH STM 4速率级(622 Mb/s)光纤用户网的光接收机放大电路。此电路由输入/输出缓冲、主放大单元、偏置补偿电路4部分组成。通过直接耦合技术提高增益,降低功耗;利用有源电感负载提高系统带宽。采用商用SmartSpice电路仿真软件和CSMC HJ 0.6μm工艺参数对该电路进行仿真。结果表明,该电路在5 V工作电压下中频增益为81 dB,3 dB带宽为470 MHz。     

Characterization of Austempered Ductile Iron Through Barkhausen Noise Measurements

The outstanding mechanical properties of austempered ductile irons (ADI) are linked to the microstructure of the matrix obtained by subjecting a ductile iron with an appropriate composition to a heat treatment called austempering. Then the microstructure of the matrix consists of bainitic ferrite with different volume fractions of retained austenite. The aim of this work is to use the magnetic Barkhausen noise (MBN) as a nondestructive method for characterizing the microstructure of ADI. First, it is shown that the amplitude and position of the peak-shaped MBN response is quite sensitive to the microstructure of the matrix of ductile irons. Thus each type of constituent (equiaxial ferrite, pearlite, martensite or bainite) exhibits a typical response and, in turn, it can be identified from the MBN response. Furthermore, a good correlation is found between MBN signal parameters and ADI heat treatment parameters, indicating that MBN is also quite sensitive to fine evolutions of the microstructure of ADI. MBN peak position is especially sensitive to the type of bainite, whereas peak amplitude is linked to the progress of the bainite reaction. Hence MBN measurements appear to be a powerful tool to assess some important microstructural features of ADI castings.     

光电设备电子机柜布线工艺研究

作为信号和电能载体的导线，同时也是噪声的载体和外来噪声侵入设备的媒体。描述了噪声通过导线侵入设备内部的方式，通过降低噪声的途径确定了机柜布线的原则，介绍了布线的要求和方法，最后提出了用布线槽布线的建议。