Multistage Zeolite Drying for Energy-Efficient Drying

This work discusses the potential of three multistage zeolite drying systems (counter-, co-, and cross-current) with a varying number of stages. The evaluation showed that for 2-4 stages with heat recovery the efficiency of the systems ranges between 80 and 90%. Additionally, by introducing a compressor, the latent heat in the exhaust air from the regenerator is recovered and used to heat the inlet air for an additional drying stage. As a result, for the counter-current drying system and compressor pressure 1.5-2 bar, a maximum energy efficiency of 120% is achieved, which results in halving the energy consumption compared to conventional drying systems.     

Mg-doped LiNi0.5Mn1.5O4 spinel for cathode materials

Lithium-ion batteries are becoming more and more important not only for portable electronic devices, but also in prevision of high power electric vehicles. In such an optic, deep studies regarding all the components of a secondary battery are in development. In this study, high voltage cathode materials have been selected. Crystals with spinel structure have a 3D vacancy pathway suitable for Li-ions transport. The material under study was LiNi_0.5Mn_1.5O₄ doped with magnesium replacing the nickel. Various samples were synthesized via three different routes: a solid-state method, a modified sol–gel method and a xerogel method. The structure and morphology of the powders were analyzed with HRTEM and XRD. Electrochemical tests were also performed. A wide range of particle sizes (from micro to nanosize) was the result of the different synthesis routes. Unfortunately pure materials were not always obtained. The electrochemical tests showed improvement of the material's cyclability, by reducing the particle size. The electrochemical tests further confirmed the existence of a Li_1+dMn_2−dO₄ impurity. The results are quite promising, however, further improvement of the purity of the electrode composition are needed.     

Strategies to increase CdTe solar-cell voltage

There is a significant difference in performance between today's highest efficiency of CdTe solar cells and single-crystal cells of comparable band gap. The largest contribution to this difference is the voltage, where the values for the best CdTe cells are about 230 mV below the best GaAs cells when an appropriate adjustment is made for band gap. CdTe voltage and fill-factor are currently compromised by low recombination lifetime (near 1 ns), low hole density (near 10¹⁴ cm^− 3), and in some cases an excessive back-contact barrier. Numerical simulation is used to evaluate how combinations of lifetime, carrier density, back electron reflection, and interfacial properties affect voltage and cell performance. Two different strategies for improving voltage and performance are explored.     

ZJ510L-B汽车用高强度热轧板的试制

珠钢150t电弧炉-LF(VD)-CSP(紧凑式带材生产)流程试生产的5～8mm ZJ510L-B(0．16C--1．22Mn)汽车用高强度热轧板的铁素体晶粒尺寸为6．0～9．2μm，带状组织为1．5～2．5级，强度极限σb562～610MPa，延伸率δ5 32．0％～38．6％。文中还分析和提出了带状组织的形成原因和改进措施。     

高温对冶金窑窑体的影响

针对冶金回转窑窑体在高温下产生的失效进行数值分析，并在此基础上对冶金窑窑体的设计方法进行修正。     

高速供送螺杆动态性能评价体系的建构

随着设备高速化的日益发展，传统的螺杆设计方法及相应的供送特性评价体系已显落后。参照蜗型凸轮动力学性能的评价方法，建立了高速供送螺杆的动态性能评价体系，为高速化供送螺杆的设计提供了性能参照指标。     

Organosoluble and light-colored fluorinated polyimides derived from 2,3-bis(4-amino-2-trifluoromethylphenoxy)naphthalene and aromatic dianhydrides

A novel fluorinated bis(ether amine) monomer, 2,3-bis(4-amino-2-trifluoromethylphenoxy)naphthalene, was prepared through the nucleophilic aromatic substitution reaction of 2-chloro-5-nitrobenzotrifluoride and 2,3-dihydroxynaphthalene in the presence of potassium carbonate, followed by catalytic reduction with hydrazine and Pd/C. A series of new fluorine-containing polyimides having inherent viscosities of 0.54 to 1.10 dl/g were synthesized from the diamine with various commercially available aromatic dianhydrides using a standard two-stage process with thermal imidization of poly(amic acid) films. These polyimides were highly soluble in a variety of organic solvents, and most of them afforded transparent, light-colored, and tough films with good tensile strengths. These polyimides exhibited glass transition temperatures (T_gs) of 247-300 °C and showed no significant decomposition below 500 °C under either nitrogen or air atmosphere. Except for the polyimide derived from pyromellitic dianhydride, the polyimide films were almost colorless, with an ultraviolet-visible absorption cutoff wavelength below 400 nm and low b∗ values (a yellowness index) of 10.7-41.9. These polyimides had dielectric constants of 3.09 to 3.65 (1 MHz) and moisture absorptions in the range of 0.2-0.3 wt%.     

导磁不锈钢毛的结构化研究

研制了一种新型的结构化钢毛——胶结钢毛。和传统的普通钢毛相比,胶结钢毛具有很强的结构刚度和很低的钢毛流失量;同时,对高岭土有较高的除铁效率。     

蓄热室效能剖析

提高蓄热室效能是降低池窑能耗的有力措施.本文分析了反映蓄热室热交换能力的综合传热系数,进一步探讨了格子砖内部热交换过程和外部热交换过程中的矛盾以及解决矛盾的方法,继而谈及妥善处理在增加格子砖热交换表面上的矛盾,最后提出了衡量蓄热室效能的技术-经济指标以及提高技术指标的主要途径.     

Experiments of Fast Learning with High Order Boltzmann Machines

This work reports the results obtained with the application of High Order Boltzmann Machines without hidden units to construct classifiers for some problems that represent different learning paradigms. The Boltzmann Machine weight updating algorithm remains the same even when some of the units can take values in a discrete set or in a continuous interval. The absence of hidden units and the restriction to classification problems allows for the estimation of the connection statistics, without the computational cost involved in the application of simulated annealing. In this setting, the learning process can be sped up several orders of magnitude with no appreciable loss of quality of the results obtained.