The suitability of round clinching tools for high strength structural steel

The use of light gauge steel framing is increasing rapidly. New methods for joining frames are being sought. One of the most promising methods is clinching. Clinching has been used for almost 20 years. There has been much research into the method, the tools, suitable materials and applications. Few articles have been published concerning clinching of high strength structural steels, which are currently the most relevant materials for house construction.This study included 11 different clinching methods. In total, 469 test pieces were produced. Despite the high strength of the materials, all the clinching methods that were examined could be used satisfactorily. The most significant result was that a round tool is appropriate for all the materials tested. In fact, in comparison with results obtained using other types of tool, when the methods were ranked by maximum shear load capacity, the round design appeared in the top three classes seven times out of nine.     

高热流密度电加热元件

本文论述了用于液态金属钠热工水力性能研究的高热流密度模拟电加热元件的结构特点、材料选择、热电偶设置及其他与棒束传热实验研究有关的问题。     

大掺量粉煤灰轻质墙体砌块的研制

大掺量粉煤灰轻质墙体砌块是以粉煤灰为主要原材料 ,普通硅酸盐水泥为胶凝材料 ,配以各种外加剂 ,经发泡剂发泡 ,在常温、常压条件下养护而成。具有重量轻、导热系数小、抗冻性高以及粉煤灰掺量大、成型方便、工艺简单、投资小、见效快等优点。     

浅谈提高信道效率的措施

提高信道的数据传输效率是人们不断追求的目标之一，也是衡量网络性能的标准之一，从几方面分析总结了为此而采取的各种措施。     

Micro-Analysis of the Contact Zone of Tribologically Loaded Second-Phase Reinforced Sol-Gel-Abrasives

Abrasives manufactured via the Sol-Gel route have increased the grinding efficiency of conventional abrasive grinding tools to a remarkable degree in the past ten years. Little is known, however, about detailed wear mechanisms of the abrasive on a nanometer scale. Sliding tests on a pin-on-disk tribometer and single grit scratching tests have therefore been performed in order to identify the wear mechanisms of these innovative materials. TEM-analysis has revealed that severe plastic deformation combined with both crack bridging and crack deflecting effects in the second phase characterise the abrasive rim zone. The surface of the abrasive is covered with an oxide debris layer which substantially improves the tribological behaviour.     

高压玻璃钢管道的研制及在油田中的应用

本文介绍了高压玻璃钢管道的特性及在我国油田的应用情况。     

Effects of hot-carrier stress on high performance polycrystalline silicon thin film transistor with a single perpendicular grain boundary

This paper is a report on the effect of a single perpendicular grain boundary on the hot-carrier and high current stability in high performance polycrystalline silicon (poly-Si) thin film transistors (TFTs). Under a hot carrier stress condition (Vg = Vth + 1 V, Vd = 12 V), the poly-Si TFT with a single grain boundary is superior to the poly-Si without any grain boundary because of the smaller free carriers available for electric conduction. The shift of transconductance in poly-Si TFT with a single grain boundary is less than 5% after hot carrier stress during a period of 1000 s. The shift of transconductance is about 25% in the case of the poly-Si TFTs without a grain boundary in the channel. On high current stress, the poly-Si TFT without the grain boundary is less degraded than the poly-Si TFT with the grain boundary because the concentrated electric field near the drain junction is lower.     

陶瓷减水剂、助磨剂、增强剂的发展现状、趋势及展望

阐述了陶瓷行业所用添加剂的分类，以及目前国际上主要生产陶瓷添加剂的厂家及主要产品，详细介绍了陶瓷坯体减水剂、助磨剂、增强剂的种类、应用、性能特点和它们与陶瓷材料的作用机理，并对陶瓷添加剂的发展前景进行了展望。     

Preparation of CeO2-ZrO2 mixed oxide with high surface area and high thermal stability

Ceria-zirconia solid particles have been recognized as a key material of the automotive exhaust catalysts since they can release and uptake oxygen owing to the rapid reversible oxidation states of cerium between Ce³⁺ and Ce⁴⁺. Several methods have recently been described to prepare the CeO₂-ZrO₂ solid particles used in the catalysts. In this paper, a new coprecipitation method is used to prepare the CeO₂-ZrO₂ solid particles. The Ce-Zr alcogel is dried and calcined in flowing N₂ not in flowing air under atmospheric pressure. The results show that the ceria-zirconia sample calcined at 650 °C has high surface area over 90 m²g⁻¹, which drops to 40 m²g⁻¹ following treatment at 900°C.