转向柱管承载能力的试验研究

在分析转向柱管花键部位应力集中情况的基础上,通过对某厂生产的转向柱管扭转破坏的试验研究,得到如下结论:①转向柱管的承载能力与其外花键齿与方向盘中心内花键齿之间的非接触区长度有关,以花键端部过渡圆弧的直径大小为宜;②安装方向盘总成时所施加在安装螺母上的拧紧力矩在70N.m左右时,转向柱管的承载能力最大。     

Application of the dynamical flexural resonance technique to industrial materials characterisation

The determination of the Young’s modulus and damping coefficient Q⁻¹ by means of non-destructive vibrating techniques has been applied to bulk and coated industrial materials. Extensions of a previous analytic model of composite beam allow to determine accurately the macroscopic modulus of each component of multilayered structural materials as coated superalloys or nitride-hardened steels. Furthermore, the study of glasses and polymers has been investigated. An attempt of normalisation of the modulus versus temperature curves allows to establish master curves depending on the specific structure, from metallic glasses to polymeric glasses. Finally a comparison of dynamical modulus and Q⁻¹ values measured between resonant (>1 kHz) and subresonant techniques (10⁻³ to 10 Hz) in relation to the loading frequencies applied in real conditions has been under folder. For metallic materials such as forged or rolled titanium alloys, the brittle-to-fragile transition occurs abruptly or smoothly with a shift of 300 K following the range of excitation frequencies.     

基于媒体用户访问行为偏好模型的代理缓存算法

目前,代理缓存技术广泛应用于改善流媒体传输的服务质量.文章从实际用户日志文件的分析出发,利用发现的用户浏览流媒体对象时的行为分布模型,提出了一种新的视频流媒体缓存算法.仿真结果证明,该算法可以通过记录很少的用户访问信息获取较高的性能表现.     

结构化P2P网络中基于流言传播的负载均衡

提出了结构化P2P网络中利用结点间周期性的拓扑维护通信来夹带、传播消息进行负载均衡的方法，具体针对Chord系统从消息传播的速度和规模两个方面分析了该方法的性能，并利用仿真进行了验证。讨论了结论在其它形式网络中的推广和实现中的消息管理问题。     

Adaptive observers as nonlinear internal models

This paper shows how the theory of nonlinear adaptive observers can be effectively used in the design of internal models for nonlinear output regulation. The theory substantially enhances the existing results in the context of adaptive output regulation, by allowing for not necessarily stable zero dynamics of the controlled plant and by weakening the standard assumption of having the steady-state control input generated by a linear system.     

集中载荷作用下的套管抗挤能力分析

根据油田套管损坏情况,建立了集中载荷作用下的套管抗挤能力计算模型,利用能量法和曲杆理论,分析研究了承受180°对称分布集中载荷、90°均匀分布集中载荷和120°均匀分布集中载荷下中厚壁套管抗挤能力,得出了理想圆管抗挤强度和套管屈曲临界挤毁压力的计算公式,通过分析比较理论解与有限元解,其最大相对误差不超过1%,得出了套管抵抗局部载荷的能力低于抵抗均布载荷的结论。     

武钢 3×10~4m~3/h 空分手动变负荷生产的探索与实践

对武钢引进的两台３×１０４ｍ３／ｈ空分设备，为改变其自动变负荷生产调节范围小、时间长的问题，采用了人工手动变负荷的操作方法。实践表明：扩大了增减产范围，缩短了调节时间，有十分明显的综合经济效益，可供大型空分变负荷生产借鉴参考。     

紧凑 Tokamak(球形环)聚变堆第一壁及中心导体柱上中子负荷及核热计算与分析

采用通用蒙特卡罗粒子输运程序ＭＣＮＰ／３８计算低环径比Ｔｏｋａｍａｋ（紧凑环或球形环）聚变堆第一壁及中心导体上的中子壁负荷分布和核热沉积分布，并与常规Ｔｏｋａｍａｋ堆第一壁上中子壁负荷分布和核热沉积分布进行比较、分析。结果表明，在中子壁负荷归一化为１ＭＷ／ｍ２时，与常规Ｔｏｋａｍａｋ相比，在低环径比Ｔｏｋａｍａｋ堆第一壁及中心柱表面上中子壁负荷分布峰值并不比常规Ｔｏｋａｍａｋ堆第一壁上的峰值高，而且低于低环径比Ｔｏｋａｍａｋ堆整个第一壁上的平均值，而中心柱上的核热沉积峰值稍高于常规Ｔｏｋａｍａｋ堆第一壁上的核热沉积峰值，但对较高中子壁负荷情况，中心导体柱上的核热沉积和辐照损伤仍可能是比较严重和值得特别研究的问题。     

Multiobjective dynamic load-dispatching method for optimal operation of power systems

A new practical method is proposed which gives a quasi-optimal solution of the dynamic load-dispatching problem formulated by a multiconstraint multiobjective optimization problem. Here, the multiple constraints are rate reserve constraints and power flow ones, and the multiple objectives are fuel cost and CO₂ emission. The proposed method is an integration of the following three techniques: (1) “Group Dispatch Scheme,” which is developed by the authors, is used to satisfy a violated constraint easily. This scheme consists of three steps. The first step is to classify all generators into two groups. One is the group which should be more loaded to satisfy the violated constraint, and the other is the should-be less loaded group. The second step is to add some load to the former group, and to subtract the same load from the latter. The third step is to dispatch each group load to each groups generators, respectively; (2) the dynamic load-dispatching algorithm is used which provides, in practical time, quasi-optimal generation trajectories; (3) the conventional weighting parametric method is used to obtain a Pareto optimal solution of multiobjective problems. The effectiveness of the method is clarified by a computer simulation on the actual power system of Kansai Electric Power Company.