船艇电站仿真与综合管理系统

论文介绍了船艇电站模拟器的组成和实时仿真功能,着重描述了多层次的图形管理系统及其仿真界面。课题将多媒体课件制作与模拟器有机地结合,涵盖了船舶主要电气设备的控制电路,既利于实践训练又便于原理的讲解,并在实践中取得了良好的效果。     

A new method of characterization for stratified thermal energy stores

A new method for characterization of stratified thermal energy stores (TES) that integrates both the first law and the second law concerns is presented here. The first law concern is incorporated into a quantity called energy response factor and the second law concern into an entropy generation ratio. A product of these two quantities is at the heart of the TES efficiency definitions. This approach removes the overemphasis of the existing methods either on the first or the second law of thermodynamics which often biases the characterization results. The information about the evolution of the temperature field of the system in time is the prerequisite of the new method. It may be obtained from experiments or from suitable numerical simulations. The current method can be easily integrated into computational fluid dynamic (CFD) simulations and thus facilitate CFD-based design analysis. As an example of such CFD-integrated analysis, a large-scale hot water seasonal heat store is numerically studied to identify the effects of aspect ratio, containment shape, internal structures, and containment size on their efficiency. The results suggest the effectiveness of the new method in deriving useful design insights.     

A load dispatch method using fractional programming and semidefinite programming

This paper describes a load dispatch method which minimizes power cost—[fuel cost]/[electric output]—for a power system with thermal plants and energy storage facilities. The proposed method employs fractional programming to convert a minimization problem with fractional objective function to a series of quadratic minimization problems, and semidefinite programming to solve converted problems. The method provides the optimum time‐dependent power output/input and storage level of energy storage facilities as well as time‐dependent power output of thermal plants. The method has been applied to a power system with five thermal plants, two energy storage facilities of various performances, and five load demands. The optimum load scheme of four time mesh points is obtained for the thermal plants and energy storage facilities. The fractional programming successfully converges the optimal scheme through a few iterations. The semidefinite programming deals with a variable matrix of 164 dimensions, and 185 inequality constraints. © 2001 Scripta Technica, Electr Eng Jpn, 138(2): 49–58, 2002     

粘弹性圆柱壳在轴向恒压下的动力稳定性

基于Timoshenko-Mindlin假设,得到考虑粘弹性的各向同性圆柱壳及纤维增强正交铺设层合圆柱壳在轴向恒压下的动力学方程。文中对两端简支的圆柱壳进行了分析,依Laplace变换,导出动力稳定的特征方程,由Routh-Hurwitz判据建立动力稳定性条件,对两类圆柱壳讨论了横向剪切变形的影响。     

Effect of crack-growth mechanism on the prediction of fracture load of adhesive joints

This paper presents observations regarding the cracking behavior of tensile-loaded structural adhesive joints. Experiments showed that fracture occurred by the development and propagation of a damage zone, rather than a single, sharp crack, and that the presence of the adhesive spew fillet did not affect the fracture load of the adhesive joints studied. For joints bonded with the mineral-filled epoxy Cybond 4523GB (American Cyanamid), there was approximately 5 mm of subcritical crack propagation prior to final fracture. Fracture-load predictions based on the initial uncracked geometry made in previous papers were unaffected by this small change in geometry. For joints bonded with the rubber-toughened epoxy Permabond ESP 310, approximately 50 mm of subcritical crack propagation was observed. It was again found that predictions made in previous papers on the basis of the initial geometry gave a good estimate of the final fracture load even though this subcritical crack propagation significantly altered the geometry, and thus the applied energy release rates. The effect of shear deformations of the adherends was also investigated, and it was found that shear deformations could be neglected in engineering calculations for joints subject to remote tensile loading.     

转向柱管承载能力的试验研究

在分析转向柱管花键部位应力集中情况的基础上,通过对某厂生产的转向柱管扭转破坏的试验研究,得到如下结论:①转向柱管的承载能力与其外花键齿与方向盘中心内花键齿之间的非接触区长度有关,以花键端部过渡圆弧的直径大小为宜;②安装方向盘总成时所施加在安装螺母上的拧紧力矩在70N.m左右时,转向柱管的承载能力最大。     

Application of the dynamical flexural resonance technique to industrial materials characterisation

The determination of the Young’s modulus and damping coefficient Q⁻¹ by means of non-destructive vibrating techniques has been applied to bulk and coated industrial materials. Extensions of a previous analytic model of composite beam allow to determine accurately the macroscopic modulus of each component of multilayered structural materials as coated superalloys or nitride-hardened steels. Furthermore, the study of glasses and polymers has been investigated. An attempt of normalisation of the modulus versus temperature curves allows to establish master curves depending on the specific structure, from metallic glasses to polymeric glasses. Finally a comparison of dynamical modulus and Q⁻¹ values measured between resonant (>1 kHz) and subresonant techniques (10⁻³ to 10 Hz) in relation to the loading frequencies applied in real conditions has been under folder. For metallic materials such as forged or rolled titanium alloys, the brittle-to-fragile transition occurs abruptly or smoothly with a shift of 300 K following the range of excitation frequencies.     

基于媒体用户访问行为偏好模型的代理缓存算法

目前,代理缓存技术广泛应用于改善流媒体传输的服务质量.文章从实际用户日志文件的分析出发,利用发现的用户浏览流媒体对象时的行为分布模型,提出了一种新的视频流媒体缓存算法.仿真结果证明,该算法可以通过记录很少的用户访问信息获取较高的性能表现.     

孔型热轧时轧制力的实用计算公式

采用修正系数法,利用板材在带刻槽的冲头进行深冲与平面冲头下深冲时的接触压力的比值确定孔型影响系数,进而推导出孔型热轧时轧制力的实用计算公式.     

结构化P2P网络中基于流言传播的负载均衡

提出了结构化P2P网络中利用结点间周期性的拓扑维护通信来夹带、传播消息进行负载均衡的方法，具体针对Chord系统从消息传播的速度和规模两个方面分析了该方法的性能，并利用仿真进行了验证。讨论了结论在其它形式网络中的推广和实现中的消息管理问题。