激光辐照对不同饵料微藻生长的影响

利用Nd:YAG激光(波长1.06μm,功率5W,照射时间0.5-3min)和Ar 激光(波长:488nm,功率70mw,照射时间5-20min)分别照射角毛藻和叉鞭金藻,辐照后进行细胞增殖和生长速率的测定。实验结果表明:照射剂量为1min的Nd:YAG激光及剂量为5min的Ar 激光对叉鞭金藻有较明显的促长效果,这两种激光处理组的细胞增殖量在辐照后的两天内较对照组分别高42.9%和48.1%,但这种促长效果随时间的推移逐渐消失。不同剂量的两种激光辐照角毛藻后,在延滞期均出现生长抑制现象,但进入指数生长期或传代培养后,剂量为1min的Nd:YAG激光及剂量为10min的Ar 激光对角毛藻有明显的促长效果,其中在指数生长期1min剂量的Nd:YAG激光处理可促长27.0%,传代培养后10min的Ar 激光处理组生长速率提高达51.2%。本文对不同激光及不同激光参数条件下,两种饵料藻的耐受性及生长特性的差异也进行分析探讨。本实验结果不仅证实了已有研究的推论,还展示出激光技术在饵料藻种选育中的应用前景。     

Combination of coating and heat treatment processes

For a proper use of coated tools and components excellent coating properties as well as excellent substrate properties of the coating/substrate composite are necessary. A well known example is the load support of hard steel substrates for thin wear resistant coatings. Therefore coating processes must be combined with heat treatment processes of the substrates, whereby several practical processing constraints like order and compatibility of the applied treatment procedures must be considered. The combination of CVD-coating plus laser beam hardening is an example of a post coating heat treatment. Applications may be possible for large forming tools made of high alloyed tool steels, which nowadays are usually through hardened after CVD-coating. Laser beam hardening offers the possibility, to harden only the highly loaded edges of the tools. The advantages of this combination are short process time, less distortion and compressive residual stresses in the substrate surface. CVD-coatings can endure laser beam hardening with suitable parameters. The influence of CVD TiN-coated steel substrates and laser beam hardening parameters on microstructures and properties of coating/substrate compounds have been investigated. Special attention was paid to overlapping hardening zones, which may occur at the start and end points of a laser hardened track. In summary, the combination of coating and heat treatment processes show a high potential to produce coating/substrate compounds with excellent coating properties as well as excellent substrate properties.     

Impact of dams on point bar habitat: a case for the extirpation of the Sacramento Valley Tiger Beetle,C. hirticollis abrupta

Quantitative analyses of flow and stage data, remote sensing and geographic information systems analysis, and field studies were used to assess the impact of dams and diversions on the point bar habitat of the Sacramento Valley Tiger Beetle (Cicindela hirticollis abrupta). The reaches of interest include sites of known historic populations of C. h. abrupta along the Sacramento River from approximately 8 km north of Colusa southward to the confluence with the Feather River and along the Feather River between Yuba City and its confluence with the Sacramento River. The results from this study show that construction of two major dams has altered flows such that prolonged and increased flows during summer, fall, and early winter have most likely disrupted life cycles, flooded larvae, drowned overwintering adults and led to high mortality. Additionally, habitat availability has decreased over time because point bars have decreased in number and area causing increased distances between populations and isolation of populations. Moreover, point bar armouring, channel scouring, altered flows, redirected flows through weirs, and lithologic controls have produced a bimodal distribution of mean grain sizes in the Sacramento River in which the more northern bars contain gravel deposits and more southern bars possess fine sands. These conditions negatively alter moisture retention and sediment compaction and, consequently, burrowing conditions needed by this tiger beetle. Additionally, more stabilized flows (reduced variability) and increased fine‐grained deposition have enabled development and encroachment of vegetation onto the sand bars. Finally, human stresses, such as foot traffic and vehicular traffic may have interfered with burrowing, ovipositing, and foraging. The combination of these stress factors has most likely led to a reduction in source populations and, ultimately, the apparent extirpation of the entire metapopulation. Copyright © 2006 John Wiley & Sons, Ltd.     

LASER ENHANCED ELECTROCHEMICAL MACHINING PROCESS

An experimental apparatus was designed and built for the hybrid process of laser enhanced electrochemical machining (ECM). Comparison experiments had been done between solely ECM and laser enhanced ECM. The machining performance of hybrid process was investigated and compared with solely ECM. The principle of the hybrid process was exposed by analyzing the microstructure of machining surface. The results show that the hybrid process has advantages in machining accuracy, surface quality, and machining efficiency.     

激光起爆与点火系统中光纤连接器

介绍了激光起爆与点火系统中光纤连接器的原理、种类、技术特性及损耗，并对激光起爆与点火系统中光纤连接器的研制动向进行了概括，最后得出一些结论。     

轴向进给比对薄壁管滚珠旋压影响的有限元分析

通过有限元数值模拟方法得出滚珠旋压中薄壁管在不同凹模旋转速度条件下轴向进给比的变化规律及工件的成形规律,并对模拟结果的等效应变分布做了分析,并与实验结果进行比较,给出薄壁管滚珠旋压时进给比的选取范围.结果表明,进给比对滚珠旋压中薄壁管直径的胀缩和工件的质量有着显著的影响.另外,从计算的模具所受的三向载荷变化情况分析了模具的使用寿命.     

热轧带肋钢筋屈服不明显原因分析与探讨

针对涟钢热轧带肋钢筋的屈服不明显现象，从金属的金相组织、人工时效、自然时效、测试方法等方面着手，寻求各因素对钢筋力学性能的影响，并阐述了该异常组织的形成机理及相关因素，指出魏氏体、粒状贝氏体等的存在是造成带肋钢筋性能异常的主要原因，同时对部分屈服不明显的带肋钢筋判定提供了较为科学的依据。     

Effect of C/Ti ratio on the laser ignited self-propagating high-temperature synthesis reaction of Al-Ti-C system for fabricating TiC/Al composites

TiC/Al composite was successfully synthesized utilizing laser ignited self-propagating high-temperature synthesis (SHS) of Al-C-Ti system with the different C/Ti molar ratio. When the molar ratio of C to Ti is below 1:1 in the starting materials, in addition to fine TiC particulates, a large amount of Al₃Ti phase was found in the composites; however, when the molar ratio of C to Ti is 1:1 in the starting materials, the Al₃Ti phase was almost completely eliminated and the distribution of TiC particulates generally appeared to be more homogeneous throughout the products synthesized.     

关于粉体成球机盘体几何形状的研究

通过对粉体小球在粉体成球机盘底上运动轨线的研究,利用Euler定理,结合其参数特点,得到了不同几何形状的盘底在成球过程中对粉体小球运动的影响,球面盘底较平面盘底更有利于成球的结论。     

大规格圆钢质量分析和控制

针对湘钢棒材厂生产大规格圆钢出现的表面质量问题，重点介绍了在成品轧机后采用U形辊道和立活套替换棍道；冷床输入辊道采用镶WT合金套；增设高压水除鳞装置；中间轧件尺寸精度控制等措施，成功的解决了大规格圆钢表面擦伤、“麻面”、尺寸超差等表面质量问题，产品质量显著提高。