Distributed architecture for energy management D-structure

Electric power systems are expanding in size and complexity, and the requirement for the energy management system (EMS) is becoming more important. In this computer control system, a single control computer is used mainly as the primary computer and its software is very complicated because of its hugh number of small, quick tasks to obtain high response speed. Therefore, much effort is needed to develop and modify the programs, and the responsiveness of this centralized architecture varies greatly when many faults occur in the power system. This paper describes a new distributed architecture for the EMS. Distributed processors execute the functions cooperatively with periodic access to the common bulletin board database in which information about the power system exist. This architecture facilitates the software development and maintenance, and it also enhances the performance by the parallel processing of the distributed functions.     

深圳福田河污染治理资源优化配置

根据不同河段的水域功能将污染严重的福田河自上而下划分为三个水污染控制单元，针对每个单元的不同环境目标和污染负荷预测得到相应的污染净化率，依此建立资源优化配置模型，由该模型获得优化决策，以期合理利用环境容量，确定最小净化费用，兴修必要的治理设施，从而保证在经济高速发展的同时，有效地控制福田河的污染问题。     

A simplified cascade current‐source inverter interconnected to a single‐phase three‐wire distribution system and its application to electric energy storage systems with batteries

A novel current source inverter system interconnected to the single‐phase grid is proposed. It has the same construction as the conventional three‐phase current source inverter that is interconnected to the single‐phase three‐wire distribution system. Though the proposed circuit has no output transformer, it can be equivalently performed as the single‐phase double cascade inverter by diverting the pole transformer in the utility system. By controlling the appropriate scheme, the output currents can be obtained as the five‐level waveforms and their distortions can be decreased sufficiently. It is applied to the interactive electric energy storage system with batteries and the basic discharging characteristics are discussed experimentally. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 150(2): 50–61, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10380     

用EGS4分析9MeV行波直线加速器屏蔽系统

采用了国际上广泛使用的ＭｏｎｔｅＣａｒｌｏ模拟计算程序ＥＧＳ４对海关集装箱检测系统用加速器屏蔽系统进行了辐射模拟分析，与实际测试数据进行分析、比较，解释了特殊剂量分布的原因，提出了系统改进的参考方案。     

Characteristics and classification of high-current fault arcs on distribution systems

When a fault occurs on transmission or distribution systems due to lightning or overvoltage, often an arc discharge occurs at the fault point. The arc discharge, which is caused by a fault current, has a high current, high temperature, strong light emission, etc., thus it sometimes causes heavy damages to electric power equipment. The arc discharge is influenced by the conditions around the arcs, i.e., gas, insulation materials, gap length, weather, etc. Also, the arc voltage along the arc column indicates the characteristics of the arc. If the voltage waveforms of the arcs caused by the fault on transmission or distribution systems are classified, it is possible to find the location and the equipment where the fault occurred. In this paper, the arc voltage data in 6-kV class XLPE cables and 6-kV class overhead lines are analyzed and an artificial neural network method is applied to classify the arc voltage waveforms. The results obtained from the six artificial neural networks developed show that the artificial neural network method is effective for classification of arc voltage waveforms if adequate input parameters are selected.     

堆底熔穿事故的场外后果及其对策

在压水堆核电站应急计划和应急响应中，堆底熔穿事故占有重要位置。本文用法国核电厂事故源项Ｓ３（对应于堆底熔穿事故）计算了在典型气象条件下的场外放射学的后果，根据一般防护决策原则和我国颁布的干预水平，提出了保护公众的应急防护措施的建议。     

应用系统工程原理 促进炼铁技术进步

应用系统工程原理,从铁前抓起,不断进行技术改造,使焦化、烧结、炼铁工艺及设备系统不断优化,从而确保了300m~3高炉的强化冶炼。     

浅论建设项目投资控制的重点

建设项目控制的重点应放在投资决策和设计阶段中,否则会造成巨大的损失。这不仅需要人们改革组织结构和管理体制,更需要从根本上转变思想观念。     

A scheduling decision aid in glass fiber manufacturing

A decision aid for scheduling production in glass fiber manufacturing industry is described. The methodology combines a linear programming (LP) optimization model with a heuristic model. The LP model determines production goals; the heuristic model then uses the LP output to incorporate system-specific constraints in developing processing sequences.