Assessment of the effectiveness of steel fibre reinforcement for the punching resistance of flat slabs by experimental research and design approach

The present paper deals with the experimental assessment of the effectiveness of steel fibre reinforcement in terms of punching resistance of centrically loaded flat slabs, and to the development of an analytical model capable of predicting the punching behaviour of this type of structures. For this purpose, eight slabs of 2550 × 2550 × 150 mm³ dimensions were tested up to failure, by investigating the influence of the content of steel fibres (0, 60, 75 and 90 kg/m³) and concrete strength class (50 and 70 MPa). Two reference slabs without fibre reinforcement, one for each concrete strength class, and one slab for each fibre content and each strength class compose the experimental program. All slabs were flexurally reinforced with a grid of ribbed steel bars in a percentage to assure punching failure mode for the reference slabs. Hooked ends steel fibres provided the unique shear reinforcement. The results have revealed that steel fibres are very effective in converting brittle punching failure into ductile flexural failure, by increasing both the ultimate load and deflection, as long as adequate fibre reinforcement is assured. An analytical model was developed based on the most recent concepts proposed by the fib Mode Code 2010 for predicting the punching resistance of flat slabs and for the characterization of the behaviour of fibre reinforced concrete. The most refined version of this model was capable of predicting the punching resistance of the tested slabs with excellent accuracy and coefficient of variation of about 5%.     

Poly(3-hydroxyalkanoate)-grafted carbon nanotube nanofillers as reinforcing agent for PHAs-based electrospun mats

Poly(3-hydroxyalkanoate)s, PHAs, have been covalently grafted onto the surface of multi-walled carbon nanotubes, MWCNTs, providing nanofillers (MWCNT-graft-PHAs) with enhanced compatibility and reinforcement effect towards PHAs. MWCNTs were first modified by in-situ generated diazonium cations obtained from a hydroxyl-containing aniline derivative, yielding MWCNTs with reactive hydroxyl surface groups, MWCNT-OH. Then, MWCNT-graft-PHAs were obtained by direct, i.e. without using any catalyst, transesterification approach. The successful chemical modification of MWCNTs surface was evidenced by Raman spectroscopy and XPS analysis confirming the covalent grafting of PHA on MWCNT. 3-Dimension mats were further produced through electrospinning of a PHA/MWCNT-graft-PHA solution providing nanocomposites with well-defined nanofibrous morphology. No aggregation of the MWCNTs was evidenced by SEM attesting that the grafting of PHA onto MWCNT improved their dispersion within the PHA matrix and consequently, the properties of the corresponding nanomaterials. Indeed, mechanical analysis results have shown that nanofibers loaded with MWCNT-graft-PHA (3 wt%) displayed excellent properties with an increase (+41%) of the tensile strain at break without any decrease of the high elastic modulus as compared to pristine PHA (131 MPa).     

Tribological behaviour of a 3Y-TZP/Ta ceramic-metal biocomposite against ultrahigh molecular weight polyethylene (UHMWPE)

This study aims to evaluate the tribological behaviour of 3Y-TZP/Ta (20 vol%) ceramic-metal composites and 3Y-TZP monolithic ceramic prepared by spark plasma sintering (SPS) against ultrahigh molecular weight polyethylene (UHMWPE). According to the results of pin (UHMWPE)-on-flat wear test under dry conditions, the UHMWPE – 3Y-TZP/Ta system exhibited lower volume loss and friction coefficient than the UHMWPE – monolithic ceramic combination due to the presence of an autolubricating layer that provides sufficient lubrication for reducing the friction. Owing to the lubrication of the liquid media, under wet conditions obtained using simulated body fluid (SBF), similar behaviour is observed in both cases. Additionally, the ceramic and biocomposite materials were subjected to a low temperature degradation (LTD) process (often referred to as “ageing”) to evaluate the changes in the tribological behaviour after this treatment. In this particular case, the wear properties of the UHMWPE-biocomposite system were found to be less influenced by ageing in contrast to the case of the UHMWPE-zirconia monolithic material. In addition to their exceptional mechanical performance, 3Y-TZP/Ta composites also showed high resistance to low temperature degradation and good tribological properties, making them promising candidates for biomedical applications, especially for orthopaedic implants.     

Pull out of FRP reinforcement from masonry pillars: Experimental and numerical results

In this paper, debonding phenomena between carbon fiber reinforced polymer (CFRP) strips and masonry support were investigated on the basis of single-lap shear tests, considering different dimensions of the bond length. To capture the post-peak response of the CFRP–masonry joint, the slip between the support and the reinforcement strip was controlled using a clip gauge positioned at the end of the reinforcement. The tests were simulated by means of a finite element model able to capture the post-peak snap-back behavior due to the failure process. The numerical model is based on zero-thickness interface elements and on a proper non-linear cohesive law. The comparison between experimental and numerical results was performed in terms of overall response, measured by both the machine stroke and the clip gauge positioned at the free end of the reinforcement. The cases of effective bond length greater and lesser than the minimum anchorage length, suggested by the CNR Italian recommendation, were considered.     

Isolation of the effect of the hairy layer length on the mechanical properties of waterborne coatings

The effect of the acidic hairy layer length on the interdiffusion of polymer between particles and as a consequence on the mechanical properties of the films produced from waterborne coatings has been studied. In order to isolate this effect, latexes with the same particle diameter and molecular weight but stabilized with poly(acrylic acid)-block-poly(butyl acrylate) (PAA-b-PBA) block copolymers of controlled and different lengths were prepared. Tensile strength measurements showed at the macroscopic level that the presence of AA chains in the particle surface reduced the mechanical properties of the films dried at room temperature, being its effect worse the longer the AA chain length. Higher annealing temperatures erased the negative effect of the acidic hairy layer on mechanical properties. The neutralization with NaOH instead of with NH₄OH also led to worse mechanical properties. These macroscopic results were supported by Fluorescence Resonance Energy Transfer (FRET) experiments that showed that at the microscopic level, the extent of interdiffusion occurred slower when the AA chains in the particles surface increased, the annealing temperature was lower and when NaOH was used as neutralizing agent instead of NH₄OH.     

Microstructure and mechanical properties of an Al–TiC metal matrix composite obtained by reactive synthesis

A metal matrix composite has been obtained by a novel synthesis route, reacting Al₃Ti and graphite at 1000 °C for about 1 min after ball-milling and compaction. The resulting composite is made of an aluminium matrix reinforced by nanometer sized TiC particles (average diameter 70 nm). The average TiC/Al ratio is 34.6 wt.% (22.3 vol.%). The microstructure consists of an intimate mixture of two domains, an unreinforced domain made of the Al solid solution with a low TiC reinforcement content, and a reinforced domain. This composite exhibits uncommon mechanical properties with regard to previous micrometer sized Al–TiC composites and to its high reinforcement volume fraction, with a Young’s modulus of ∼110 GPa, an ultimate tensile strength of about 500 MPa and a maximum elongation of 6%.     

A first-principles investigation on mechanical and metallic properties of titanium carbides under pressure

The titanium carbides are potential candidates to achieve both high hardness and refractory property. We carried out a structural search for titanium carbides at three pressures of 0 GPa, 30 GPa and 50 GPa. A phase diagram of the Ti-C system at 0 K was obtained by elucidating formation enthalpies as a function of compositions, and their mechanical and metallic properties of titanium carbides were investigated systematically. We also discussed the relation of titanium concentration to the both mechanical and metallic properties of titanium carbides. It has been found that the average valence electron density and tractility improved at higher concentrations of titanium, while the degree of covalent bonding directionality decreased. To this effect, the hardness of titanium carbide decreases as the content of titanium increases. Our results indicated that the titanium content significantly affected the metallic properties of the Ti-C system.     

Structural modifications and fibre processing of hydroxy-functionalised mesogenic polyazomethines

A number of semiflexible homopolyazomethines and copolyazomethines based on hydroxy-functionalised mesogenic cores have been synthesised and characterised. The reported polymers include structural modifications such as an alteration of the coaxiality, shortening of the flexible spacers or copolymerisation to attain materials with reduced melting temperatures and suitable processability. These structural alterations have been introduced by condensing different ,ω-bis-[(4-formyl-3-hydroxyphenyl)oxy]alkanes with 2-methyl-1,4-phenylenediamine and/or 4-methyl-1,3-phenylenediamine. Fibres have been melt extruded from those nematic polyazomethines with the most favourable thermal properties. As-spun and tension-annealed fibres have been investigated by thermal analysis (TGA and DSC), X-ray diffraction and SEM microscopy in an attempt to infer a relationship between microstructure and tensile properties. From the results presented here, copolymerisation incorporating flexible spacers of different lengths seems to be the best strategy to balance ease of processing and tensile properties. Some of the fibres have improved mechanical properties compared with those previously reported for this class of semiflexible polyazomethine. A nematic polyazomethine with a decamethylenic spacer has also been modified with low percentages of several metal ions [Fe(III), Zn(II), V(IV) and Ni(II)] in order to establish a comparison with previously reported Cu(II)-modified fibres.     

Fracture toughness of PAN-based carbon fibers estimated from strength-mirror size relation

Fracture toughness (K_IC) of representative high-strength type PAN (polyacrylonitrile)-based carbon fibers, Torayca™ T300 and T800H, with or without artificial surface defects, were estimated to be ca. 1 MPam^1/2 from the tensile strength vs. fracture mirror size relation, assuming a constant crack-to-mirror size ratio. The corresponding critical energy release rate (Γ) was ca. 7.4 J m⁻², which was close to the value derived from the reported surface energies for a graphite crystal. Similar K_IC values were obtained for the old-type PAN-based carbon fibers from the reported data by the use of the present estimation procedure.     

Fracture and deformation properties of Ni-Fe superalloy in cryogenic high magnetic field environments

The present paper includes experimental and analytical data on the fracture properties of a nickel-iron superalloy, a ferromagnetic austenite, at 4 K in magnetic fields of 0 and 6 T. The tensile, notch tensile and small punch tests are employed. A finite element analysis is also performed to convert the experimentally measured load-displacement data into useful engineering information. To interpret the results we review the available theory of the influence of magnetic field on the stress intensity factor for a crack in ferromagnetic materials.