A VLSI architecture for a half-edge-based corner detector

Corner detection is a low-level feature detection operator that is of great use in image processing applications, for example, optical flow and structure from motion by image correspondence. The detection of corners is a computationally intensive operation. Past implementations of corner detection techniques have been restricted to software. In this paper we propose an efficient very large-scale integration (VLSI) architecture for detection of corners in images. The corner detection technique is based on the half-edge concept and the first directional derivative of Gaussian. Apart from the location of the corner points, the algorithm also computes the corner orientation and the corner angle and outputs the edge map of the image. The symmetrical properties of the masks are utilized to reduce the number of convolutions effectively, from eight to two. Therefore, the number of multiplications required per pixel is reduced from 1800 to 392. Thus, the proposed architecture yields a speed-up factor of 4.6 over conventional convolution architectures. The architecture uses the principles of pipelining and parallelism and can be implemented in VLSI.     

缝纫设备输送动力装置的分析

文章介绍了几种缝纫设备输送动力装置的送布原理，认为应针对不同的面料特性及经制工艺要求，选用合适的设备输送系统。     

SHS of shape memory CuZnAl alloys

Aiming at preparation of shape memory alloys (SMAs), we explored the SHS of Cu_{1 − x} Zn_{1 − y} Al_{1 − z} alloys (0.29 < x < 0.30, 0.74 < y < 0.75, and 0.83 < z < 0.96). The most pronounced shape memory effect was exhibited by the alloys of the following compositions (wt %): (1) Cu(70.6)Zn(25.4)Al(4.0), (2) Cu(70.1)Zn(25.9)Al(4.0), and (3) Cu(69.9)Zn(26.1)Al(4.0). The effect of process parameters on the synthesis of CuZnAl alloys was studied by XRD, optical microscopy, and scanning electron microscopy (SEM). The grain size of CuZnAl was found to depend on the relative amount of the primary CuZn and AlZn phases. Changes in the transformation temperature and heat of transformation are discussed in terms of ignition intensity and compaction. Mechanism of the process depends on the level of the temperature attained relative to the melting point of components. At the melting point of AlZn, the process is controlled by the solid-state diffusion of AlZn into a product layer. The ignition temperature for this system depends on the temperature of the austenite-martensite transformation in CuZnAl alloys. The composition and structure of the products was found to markedly depend on process parameters. The SHS technique has been successfully used to prepare a variety of SMAs.      

圆盘锯机性能提升途径

圆盘锯机在线材厂投入使用时不能满足生产的需要：锯切周期太长，锯片使用性能差，经过对设备进行技术改造和对设备操作规程进行优化，以及在操作上加强管理，使之关键指标大幅度提升，为圆盘锯机的使用改善提供了新的思路。     

Microstructural and compositional aspects of ZnO-based varistor ceramics prepared by direct mixing of the constituent phases and high-energy milling

ZnO-based varistor samples were prepared by the direct mixing of the constituent phases (DMCP) and sintering at 1100 °C for 2 h. The influence of the starting powder mixture's composition – the amounts of the pre-reacted varistor compounds and their composition – and its preparation, either with or without mechano-chemical activation (MCA), on the microstructure, phase composition and electrical characteristics of the varistor samples was studied. It showed that MCA improved the density and microstructural homogeneity of the varistor samples. MCA strongly affected the grain growth: it enhanced the nucleation of inversion boundaries (IBs) in the ZnO grains and the IBs-induced grain-growth mechanism resulted in uniform grain growth and hence a microstructure with smaller ZnO grains and a narrower grain size distribution. The final phase composition of the samples prepared by the DMCP method mainly depended on the presence of varistor dopants that can prevent the formation of the pyrochlore phase, especially Cr₂O₃, while MCA can affect it mostly by providing a homogeneous distribution of those dopants. The DMCP varistor samples prepared with MCA had much better current–voltage characteristics than the samples of the same composition prepared from unactivated powders.     

Triple tangent flank milling of ruled surfaces

This paper presents a positioning strategy for flank milling ruled surfaces. It is a modification of a positioning method developed by Bedi et al. [Comput Aided Des 35 (2003) 293]. A cylindrical cutting tool is initially positioned tangential to the two boundary curves on a ruled surface. Optimization is used to move these tangential points to different curves on the ruled surface to reduce the error. A second optimization step is used to additionally make the tool tangent to a rule line, further reducing the error and resulting in a tool position, where the tool is positioned tangential to two guiding rails and one rule line. The resulting surface has 88% less under cutting than the method of Bedi et al.     

氧化铝熟料单筒冷却机节能技术改造

本对影响氧化铝熟料单筒冷却机冷却效率的因素进行了分析，并提出了相应的节能技术改造措施，取得了明显的节能效益。     

直流电动机参数测定

根据直流电机的可逆原理并利用常规的实验仪表，可以简便、准确地测出直流电动机的主要参数－电磁转矩、输出转矩和效率．     

机械合金化的原理及在磁性材料研究中的应用

介绍了机械合金化的原理和描述机械合金化过程的理论模型。综述了机械合金化在磁性材料研究中的应用，并对目前研究中的存在的问题及发展前景进行了分析。     

某微型起爆器引起的一起误爆事故分析

该文分析某微型起爆器引起的一起误爆事故，指出该起爆器设计上的缺陷及其对作业安全的威胁，提出防患建议。