带隔板底水油藏油井临界产量计算公式

本给出了带隔板底水油藏油井的监界产量计算公式，它适用于所有带隔板底水油藏的油井。     

地面油管漏失定量测试方法探讨

对油管漏失进行定量测试的方法确定具体漏失位置。方法运用双频道回声探仪探测动液面的原理和工作方法，根据油管漏失形成的死油坏在测试曲线上出现特殊波位置判断油管漏失位置。结果：经过７０多井次的现场试验，该方法具有较高的准确性和可靠性。结论：利用特殊波可以有效监测油管漏失，并具有推广使用价值。     

L－B膜修饰电极循环伏安行为模拟──（Ⅰ）电荷转移速度常数对循环伏安性能的影响

本文用计算机数字模拟方法研究了电活性分子多层Ｚ型Ｌ－Ｂ膜修饰电极的循环伏安行为。计算了电极与修饰Ｌ－Ｂ膜分子第一层之间的电荷转移速度常数Ｋ_ｏ，Ｌ－Ｂ膜分子层间的电荷转移速度常数ｋ_ｉ；对峰电位差△Ｅ_ｐ及阳极峰面积Ｑ的影响，以及在不同条件下各层分子的氧化态分数随扫描时间的变化。为研究和设计电活性分子修饰电极的实际体系提供了大量数据和信息。     

电力变压器动稳定破坏的分析和对策

对大型电力变压器绕组在变压器发生外部短路时所受的辐向力和轴向力进行了分析和计算，比较了国内外不同的计算方法和得出的不同结果。     

水溶性防氧化剂在SMT用印制板上的应用

水溶性的防氧化剂是一种有机可焊性保护剂。其方法是在印制板完全阻焊、字符层的印刷，并经电检之后，通过表面浸渍在裸铜的贴片位或通孔内形成一种耐热性的有机可焊性膜层。这种有机、可焊、耐热的膜层，膜厚可达0.3-0.5mm，其分解的温度可达约300℃，传统的印制板的热风整平法亦无法满足QFP愈来愈密集的需求，同时也无法满足SMD表面平整度的要求，更无法适应PCB薄型化生产。烷基苯并咪唑的OSP法能弥补这项缺陷，因而在PCB业乃至SMT产业中得到了广泛的应用。     

预处理工艺对硬质合金与金刚石膜间粘结力的影响

在两种经不同预处理的硬质合金YG8基底上，采用微波等离子体化学气相沉积法，在微波功率2kW，压强4.0kPa和6.5kPa，CH4和H2流量分别为1.6cm/s和100.0cm/s的条件下生长金刚石薄膜。利用X射线衍射检测了金刚石薄膜是否存在，用拉曼光谱分析了薄膜的质量，用金相显微镜观察了薄膜的洛氏硬度压痕，标定并比较了不同预处理工艺膜与基底的结合力。实验结果表明，不同的预处理方法对于粘结力的影响不大，最主要的因素是钴含量的多少。     

自旋式脱接器在临盘油田的应用

为保障临盘采油厂的大泵井正常生产 ,购进了自旋式脱接器。这种脱接器由上体和下体两部分组成 ,上体包括轨道管和轨道套 ;下体包括接头、挡圈、弹簧、滑套和中心杆。自旋式脱接器可在任意位置和角度对接和脱开 ,对接和脱开时只需下放和上提抽油杆柱即可完成。当泵砂卡时 ,左旋抽油杆柱即可脱开 ,解决了砂卡井脱接器不能脱开的难题。该脱接器可重复对接12 0次以上 ,耐疲劳寿命 7× 10 7次以上     

不锈钢及镍基堆焊层厚度测量

叙述了运用磁性法或超声法对核电和化工容器中不锈钢及镍基堆焊层厚度进行测量的原理、方法及主要影响因素 ,比较了这两种方法的测量结果     

The influence of the fabrication process on the buckling of thin-walled steel box sections

Steel box sections are usually fabricated from flat plates which are welded at the corners. The welding process can introduce residual stresses and geometric imperfections into the sections which can influence their strength. For some thin-walled sections, large periodic geometric imperfections have been observed in manufactured sections. Subsequent investigations have indicated that the imperfections are in fact buckling deformations i.e. the box section has buckled due to welding residual stresses prior to any application of external load. The welding procedure and the behaviour of the box sections under load has been modelled using a finite element analysis that accounts for both geometric and material non-linearities. Tests have been carried out on box sections with a range of width to thickness ratios for the plate elements. Modelling has been shown to give good correlation with the test results. The conditions for buckling to take place as a result of the welding process have been established. A design method has been proposed.     

Evaluation of Monkman-Grant parameters for type 316LN and modified 9Cr-Mo stainless steels

The Monkman-Grant (M-G) and its modified parameters were evaluated for type 316LN and modified 9Cr-Mo stainless steels prepared with minor element variations. Several sets of creep data for the two alloy systems were obtained by constant-load creep tests in 550-650°C temperature range. The M-G parameters,m, m’,C, andC’ were proposed and discussed for the two alloy systems. Them value of the M-G relation was 0.90 in type 316LN steel and 0.84 in modified 9Cr-Mo steel. Them’, value of the modified relation was 0.94 in type 316LN steel and 0.89 in 9Cr-Mo steel. Although creep fracture modes and creep properties between type 316LN and modified 9Cr-Mo steels showed a basic difference, the M-G and its modified relations demonstrated linearity quite well. Them’ of modified relation almost overlapped regardless of the creep testing conditions and chemical variations in the two alloy systems, and the parameterm’ was closer to unity than that of the M-G relation.