Coking kinetics of a Cr2O3/Al2O3 catalyst during 1-butene dehydrogenation: Effect of H2 partial pressure

The influence has been studied of the partial pressure of hydrogen (0–30 kPa) upon the coking rate of a Cr₂O₃/Al₂O₃ commercial catalyst during 1-butene dehydrogenation. Coke deposition has been analysed using a monolayer-multilayer reversible coke growth model (MMRC model). This model provides good fits to the experimental data, within the range of partial pressure of H₂ studied, and allows us to estimate the main kinetic parameters involved in the coking-deactivation process. The results obtained reveal a dual effect of hydrogen: competition against 1-butene for the active sites and the removal of coke precursors from the catalyst surface. Bom effects diminish the coking rate as the H₂ partial pressure is increased.     

Electrochemical performance of nanocrystalline Li3V2(PO4)3/carbon composite material synthesized by a novel sol–gel method

A novel sol–gel method based on V₂O₅·nH₂O hydro-gel was developed to synthesize nanocrystalline Li₃V₂(PO₄)₃/carbon composite material. In this route, V₂O₅·nH₂O hydro-gel, NH₄H₂PO₄, Li₂CO₃ and high-surface-area carbon were used as starting materials to prepare precursor, and the Li₃V₂(PO₄)₃/carbon was obtained by sintering precursor at 750 °C for 4 h in flowing argon. The sol–gel synthesis ensures homogeneity of the precursors and improved reactivity. The sample was characterized by XRD, SEM and TEM. X-ray diffraction results show Li₃V₂(PO₄)₃ sample is monoclinic structure with the space group of P2₁/n. The TEM image indicates that the Li₃V₂(PO₄)₃ particles modified by conductive carbon are about 70 nm in diameter. The Li₃V₂(PO₄)₃/carbon system showed that the discharge capacities in the first and 50th cycle are about 155.3 and 143.6 mAh/g, respectively, in the range of 3.0–4.8 V. The sol–gel method is fit for the preparation of Li₃V₂(PO₄)₃/carbon composite material which may offer some favorable properties for commercial application.     

月桂氮草酮研究进展

介绍了月桂氮草酮作为高效皮肤促渗剂的发展概况、合成工艺、研究进展及其应用前景。     

F离子掺杂TiO2的性能研究

以NH4F为掺杂剂，采用溶胶-凝胶法制备F离子掺杂型TiO2光催化剂，对其进行XRD、XPS和PL表征，结果表明，F离子掺杂ToO2由于Ti—F配位体的形成而能抑制金红石相的生成，同时F离子掺杂能增加TiO2表面缺陷浓度并降低Ti2P键的结合能，另外，由于F离子能取代Ti—OH配位体而降低了表面羟基氧浓度．光催化研究结果表明，F离子掺杂提高了TiO2光催化活性近1．5倍．     

纳米SiO2粉体的制备与研究

纳米SiO2粉体的制备是以硅酸钠和盐酸为原料，添加适宜的稳定剂(非离子表面活性剂)和分散剂，在适宜的pH值和温度下，采用化学沉淀法合成。研究表明，要得到性能优良纳米的SiO2粉体，最佳工艺条件为：温度20～40℃，pH=6，反应液质量浓度P1=20g／L，P2=1．20g／L，反应时间15min。结果表明：制备的纳米SiO2粒径30～50nm，比表面积大，分散性好，质量优良，可达到产业化的生产。     

Adsorption and desorption characteristics of 2-methyl-4-chlorophenoxyacetic acid onto activated carbon

Adsorption and desorption characteristics of the 2-methyl-4-chlorophenoxyacetic acid (MCPA) from aqueous solution onto the activated carbon (GAC, F-400) were studied. Adsorption equilibrium capacities of the MCPA increased with decreasing pH and temperature of the solution. Adsorption equilibrium of the MCPA could be represented by the Sips equation. The internal diffusion coefficients were determined by comparing the experimental concentration decay curves with those predicted from surface diffusion model and pore diffusion model. The adsorption model based on the linear driving force approximation (LDFA) was used for simulating the adsorption behavior of the MCPA in a fixed bed. Over ninety five percent desorption of the MCPA could be obtained using distilled water.     

ZrO2载体催化剂的制作及特性探讨

选择有应用价值的CuO/ZrO2体系，通过大量试验寻找到了一种以ZrO2为载体的高比表面催化剂的制备方法。     

Deactivation of metal catalysts in liquid phase organic reactions

The paper gives a general survey of the factors contributing to the deactivation of metal catalysts employed in liquid phase reactions for the synthesis of fine or intermediate chemicals. The main causes of catalyst deactivation are particle sintering, metal and support leaching, deposition of inactive metal layers or polymeric species, and poisoning by strongly adsorbed species. Weakly adsorbed species, poisons at low surface coverage and solvents, may act as selectivity promoters or modifiers. Three examples of long term stability studies carried out in trickle-bed reactor (glucose to sorbitol hydrogenation on Ru/C catalysts, hydroxypropanal to 1,3-propanediol hydrogenation on Ru/TiO₂ catalysts, and wet air oxidation of paper pulp effluents on Ru/TiO₂) are discussed.     

原位聚合制备尼龙6/纳米SiO2复合材料研究

对原位聚合制备尼龙6／纳米SiO2进行研究。结果表明，无论是否对纳米SiO2复合材料进行偶联化处理，其表面均将在原位聚合过程中与尼龙6产生接枝；SiO2表面接枝物的生成，可在某种程度上造成体系结晶程度的降低，但复合体系的力学性能主要由SiO2粒子的分散程度、粒子和其体之间的相界面性质等因素决定；采用经偶联剂处理并具有较小粒径和较大比表面积的SiO2对尼龙6进行复合，可使复合体系的力学性能指标达到较高的水平，且硅烷偶联剂的最佳用是为SiO2的3％左右。     

Low cost coal-based carbons for combined SO2 and NO removal from exhaust gas

The aim of this paper is to show how a cheap carbonaceous material such as low rank coal-based carbon (or char) can be used in the combined SO₂/NO removal from exhaust gas at the linear gas velocity used in commercial systems (0.12 m s⁻¹). Char is produced from carbonization and optionally activated with steam. This char is used in a first step to abate the SO₂ concentration at the following conditions: 100 °C, space velocity of 3600 h⁻¹, 6% O₂, 10% H₂O, 1000 ppmv SO₂, 1000 ppmv NO and N₂ as remainder. In a second step, when the SO₂ concentration in the flue gas is low, NO is reduced to N₂ and steam at the following experimental conditions: 150 °C, space velocity of 900 h⁻¹, 6% O₂, 10% H₂O, 0-500 ppmv SO₂, 1000 ppmv NO, 1000 ppmv NH₃ and N₂ as remainder.It has been shown that the presence of NO has no effect on SO₂ abatement during the first step of combined SO₂/NO removal system and that low SO₂ inlet concentration has a negligible effect on NO reduction in the second step. Moreover, this char can be thermally regenerated after use for various cycles without loss of activity. On the other hand, this regenerated char shows the highest NO removal activity (compared to parent chars, either carbonized or steam activated) which can be attributed to the activating effect of the sulfuric acid formed during the first step of the combined SO₂/NO removal system.