微通道中两相流压降与传质的研究

以氮气和水为实验体系,采用均质混合模型,研究微混合器的微通道中两相流通过微通道的压降,并测定了两相流的传质系数.结果表明,微通道当量直径为95.2 μm,气体速率为1.089～4.355 m/s,液体速率为0.006 41～0.170 90 m/s的条件下,均质混合模型计算压降值与实测值吻合良好.气速为1.633～3.484 m/s,液速为0.025 6 m/s时,随着气速增加,传质系数呈递增的趋势.气速为1.633～3.484 m/s,液速为0.019 2 m/s时,随着气速增加,传质系数先增加后降低然后再增加.传质系数对液速变化更为敏感.     

管井和轻型真空井点组合 在某电厂深基坑降水中的应用

以某电厂翻车机室为研究对象, 针对其深基坑降水降深大, 工期紧等特点, 主要介绍了该工程的工程地质及水 文地质条件, 并且运用管井和轻型真空井点组合降水的方法, 设计了基坑降水处理的施工方案, 确定了降水的各个 参数。实践证明, 管井和轻型真空井点组合应用效果良好, 有效保证了工程的顺利进行, 加快了工程进度, 缩短了工 期。结合实例提出了降水过程中应注意的问题及应对措施。     

异常高压气井生产动态仿真研究及应用

异常高压气井生产动态仿真方法不仅改变了传统物理仿真成本高、过程复杂的缺点,而且具备了计算机仿真模拟的准确性。考虑异常高压气井流体高压、高温的特点,本文将异常高压气井生产压降分解为地层流动压降、井筒流动压降和嘴流流动压降三个过程,并建立了气井生产动态流动数学模型;本文利用计算机仿真技术模拟了异常高压气井地层流体流动过程、井筒流体流动过程和气嘴流体流动过程,并预测了气井生产动态流动参数,为下步异常高压气井动态配产提供了基础数据。通过实例分析,将计算机仿真预测出的异常高压气井流动参数代入优化配产模型计算出配产结果与实际配产结果十分接近,表明异常高压气井生产动态仿真对实际生产具有重要的指导意义。     

勃劳特换热器的性能

勃劳特换热器的性能周绪美，陈建铭，张鹏远，冯元鼎，丁华（北京化工大学化学工程系）关键词勃劳特换热器；压降１引言在生产过程中，气体与气体之间进行热量交换的换热器，在性能评比时，应该用两项指标来衡量。其一是单位产品所需传热面积要小，其二是单位压降的传热膜...     

Contributions to the Ohmic Drop in the Electrolysis of ZnCl2 in a Molten Chloride Electrolyte

The electrowinning of zinc from zinc chloride with a molten chloride electrolyte was investigated. The electrolysis of zinc chloride shows ohmic limitations. The energy consumption is to a large extent determined by the anodic reaction, the evolution of chlorine. The chlorine gas plume was visualised in a see-through furnace and images were analysed to determine the plume angle. This parameter serves as an input parameter for a model to determine the ohmic contributions of the electrolyte, the plume and a layer of chlorine bubbles sticking to the anode, as well as the plume velocity. The results indicate that the major contribution (60%) to the ohmic drop is due to a stagnant layer of bubbles growing and sticking to the anode, thereby decreasing the effective anode area by coverage. The plume velocity influences coverage characteristics to some extent, which influences the ohmic drop.     

In situ visualization of drop deformation,erosion, and breakup in high viscosity ratio polymeric systems under high shearing stress conditions

In this paper, deformation and breakup under simple shear of single molten polymer drops in a polymer matrix were investigated. Flow visualization was carried out in a Couette‐Flow apparatus under relatively high shear rates and temperatures up to 230°C. Drop/Matrix combinations were composed of polystyrene drops of 0.5–0.6 mm in diameter in polyethylene matrix, and ethylene–propylene copolymer drops of approximately the same size in polypropylene matrix. The deformation and breakup processes were studied under steady state and time‐dependent shearing conditions. Either for steady state or time‐dependant shearing conditions, drop elasticity generated at relatively high shear rates helped the drops to align perpendicular to the flow direction, i.e., parallel to vorticity axis. Also, the most striking non‐Newtonian effects for the high viscosity ratio systems were the surface erosion and the drop splitting mechanisms. The particles eroded off the main droplet surface were very fine, in the range of 10–50 μm, and led to a significant reduction in main drop size before its final breakup. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2582–2591, 2006     

一种降压型开关电源芯片电路的研究与设计

设计了一款PWM控制模式降压式（buck）直流一直流转换器芯片。该芯片为电压反馈控制模式,内部补偿使得反馈控制有很好的线性和很快的负载响应而无需通过外部设计。芯片采用CMSC0．5μm BCD工艺实现。PSPICE仿真结果表明,输出电压只有大约50mY的纹波,静态电流为3mA左右。输出电压在低于0．5V时,芯片具有短路降频功能,工作频率由81KHz降到23KHz左右,输出负载由0．2A跳变到2A时具有很好的负载调整率,大约为0．2％,转换效率可以达到85％以上。     

Interfacial tension measurement between immiscible polymers: improved deformed drop retraction method

This paper describes an improvement of the technique to measure interfacial tension in immiscible polymer blends. Our method is based on the droplet retraction method, in which one relates the kinetics of relaxation of a deformed droplet to the interfacial tension between the matrix and droplet. Previously, the problem with this technique has been the difficulty in preparing axisymmetric ellipsoidal droplets. In our work, we demonstrate that perfect axisymmetric ellipsoidal droplets are produced at a later stage of relaxation of short imbedded fibers. With this technique, we utilize the strengths of both the deformed droplet method and the imbedded fiber retraction method while overcoming their shortcomings. The interfacial tension value thus obtained was compared to that by conventional methods. Additionally, the effect of confinement by external walls on the interfacial tension measurement was studied. Confinement affects interfacial tension measurement when the gap between the walls is less than two times the equilibrium drop size.     

浅析注塑工艺与设备对聚酯瓶坯粘度降的影响

本文就碳酸饮料瓶用聚酯瓶坯生产过程的三个环节中，因注塑工艺与设备影响所产生的粘度降提出解决方法。     

颗粒流体两相流基本方程中压差力和曳力系数的计算

本文总结了颗粒流体两相流基本方程的压差力表达方式和推导颗粒流体系统曳力系数计算公式的力平衡原理，提出了一种分析压差力的简单方法，阐明了各种压差力表达方式间的关系及对应的两相流基本方程的曳力系数的计算方法