接触网零件振动试验方法探讨

通过对接触网零件用紧固件的耐振动性能进行振后扭矩测试和横向振动采用压力环测试应变进行对比分析，提出了合理的接触网零件耐振动性能试验方法。     

钛容器的特点

根据钛材的化学、物理、力学和工艺性能介绍了钛容器在设计、制造、检验和应用方面的特点。     

用小尺寸R－CT试样研究核压力容器钢断裂韧性及与Charpy试样的比较

提出了一种用双边带深侧槽的小尺寸圆形紧凑拉伸试样评定核压力容器（ＲＰＶ）钢断裂韧性的单试作试验方法，给出了用该方法测定的两个厂家生产的核压力容器用Ａ５０８ＣＬ３钢的断裂韧性参数，还与Ｃｈａｒｐｙ试样的试验结果及大尺寸标准试样的试验结果进行了比较。研究结果表明：用双边带深侧槽的小尺寸Ｒ－ＣＴ试样测得的断裂韧性值比相同恻槽深度预制疲劳裂纹Ｃｈａｒｐｙ试样的测试值更接近有效断裂韧性值，所以，用于核压力容器断裂韧性的监测是可行的。     

An experimental study on the pumping performance of molecular drag pumps

The pumping performance of molecular drag pumps (MDP) has been investigated experimentally. The experimented MDPs are a disk-type drag pump (DTDP), helical-type drag pump (HTDP) and compound drag pump (CDP), respectively. In the case of the DTDP, spiral channels of a rotor are cut on both upper surface and lower surface of a rotating disk, and the corresponding stator is a planar disk. In the case of the HTDP, the rotor has six rectangular grooves. The CDP consists with the DTDP, at lower part, and with the HTDP, at upper part. The experiments are performed in the outlet pressure range of 0.2–533 Pa. The inlet pressure and compression ratio are measured under the various conditions of outlet pressure and throughputs, and nitrogen is used for the test gas. At the outlet pressure of 0.2 Pa, the ultimate pressure has been reached to 1.0 × 10⁻² Pa for the HTDP, 1.3 × 10⁻⁴ Pa for the DTDP, and 3.6 × 10⁻⁵ Pa for the CDP. The maximum compression ratio of the CDP is much higher than those of the DTDP or HTDP. Consequently, the ultimate pressure of the CDP is the lowest one.     

川中地区上三叠统天然气地球化学特征及成藏过程探讨

川中地区上三叠统是一套自生自储的天然气成藏系统，天然气中甲烷含量为88%～96％，重烃（C2＋）含量一般在6％～9％之间，二氧化碳和硫化氢等非烃气体含量普遍较低；天然气干燥系数（C1／C2＋）为5～15，并且随深度增加而呈现升高的趋势；天然气和凝析油轻烃中的甲基环己烷、庚烷和异庚烷值变化表明天然气主要来源于腐殖型母质；天然气甲烷和乙烷碳同位素分别为-39．00‰～-41．00‰和-25．00‰～-27．00‰，具有典型煤成气特征。川中地区上三叠统烃源岩在燕山期持续沉降埋藏过程中，达到高成熟早期阶段；在喜山期，该地区大约2500m地层的剥蚀，使地层温度和压力大幅度降低，故储层中早期低成熟残余天然气的卸压膨胀作用和水溶气的脱溶作用为晚期天然气聚集成藏提供了重要的气源，同时也使气藏中甲烷碳同位素变轻。     

胜利701气枪震源船改造设计

阐述胜利701气枪震源船震源系统的改造设计。改造设计使胜利701船达到了Ⅱ类航区海船的规范要求，满足了海上三维勘探和高分辨勘探的发展需要，为以后类似船舶的改造提供了经验。     

On the dynamics of non-linear viscoelastic solids with material moduli that depend upon pressure

We investigate the dynamic response, of a generalization of an incompressible Kelvin-Voigt viscoelastic solid, whose viscosity depends on the pressure. Bodies with pressure-dependent material moduli have relevance to numerous technologically significant problems in geomechanics, the mechanics of granular media and powder compaction. We obtain analytical results for creep and recovery phenomena as well as solutions to the propagation of waves in such bodies. We are able to obtain explicit exact solutions that clearly illustrate the marked difference in the response of bodies with pressure-dependent material moduli as opposed to their counterparts whose moduli do not depend on the pressure. We also show that the governing equations for such materials can change type, and that their solutions exhibit singularities and localization.     

变压吸附制氧设备真空风机入口压力低分析和处理

介绍了邯钢动力厂真空变压吸附制氧设备的工艺流程,从切换阀本体、电磁阀及仪表气源等方面分析和总结了真空风机入口压力低引起系统联锁停车故障原因,并介绍了相应的处理措施。     

An investigation of the unstable region for dense phase conveying in sliding bed flow

For fine powdered materials, capable of being conveyed in dense phase, a conveying region exists in which instability in flow and pipeline blockage can occur if the pressure gradient available is insufficient to maintain a minimum value of solids loading ratio. A reduction in material flow rate can also lead to pipeline blockage in this region. Conveying trials under-taken with cement are used to illustrate the nature of the problem.