LMB-018A显示模块的原理及与DSP的接口

LMB-018A是深圳拓微电子有限公司推出的内含控制器和驱动器的点阵式液晶显示模块。文中介绍了该模块的原理及功能．给出了其与DSP接口的硬件电路和软件设计方法。     

Determination of the uranium enrichment with the NaIGEM code

The traditional method used to non-destructively determine the uranium enrichment with an NaI detector is based on the “enrichment meter principle” (Progress report LA-4605-MS, Los Alamos National Laboratory, NNM, 1970, p. 19), which involves measuring the intensity of the 186 keV line of ²³⁵U by selecting two regions of interest for the peak and the background. This type of method suffers from several limitations, the most limiting of which are the impossibility to make wall thickness correction or to take the inference of foreign radioisotopes into account. The NaIGEM software (A guide for using NaIGEM code, version 1.5 for DOS and Windows, 2001; Nucl. Instr. and Meth. A 458 (2001) 196) was developed to overcome these limitations by calculating the 186 keV line intensity with a fitting procedure. The code was tested in different measurement conditions on the wide variety of certified samples, in particular, on reprocessed uranium and on depleted material with thick steel filters interposed between the source and the detector. The results are presented to illustrate the performance and limitations of the tested version (A guide for using NaIGEM code, version 1.5 for DOS and Windows, 2001). The general performance is good except in the case of low-enriched uranium in thick containers.     

A new colloidal precursor cooperative conversion route to nanocrystalline quaternary copper sulfide

A novel milk-like Cu-thiourea colloid has been synthesized. Nanocrystalline quaternary copper sulfide Cu₂FeSnS₄ was obtained through the Cu-thiourea colloidal precursor cooperative conversion route at low temperature. The samples were characterized by means of X-ray powder diffraction, transmission electron microscopy, scanning electron microscopy, inductively coupled plasma atomic emission spectroscopy, and X-ray energy dispersive spectroscopy techniques. The reaction details and features were described and discussed.     

Acidity and basicity of hydrotalcite derived mixed Mg-Al oxides studied by test reaction of MBOH conversion and temperature programmed desorption of NH3 and CO2

Mg-Al hydrotalcites intercalated with five different interlayer anions—CO₃²⁻, SO₄²⁻, Cl⁻, HPO₄²⁻ or terephthalate—were synthesized by either the coprecipitation or ion-exchange method. The structure of the as-synthesized samples and the presence of intended anions in the interlayer gallery of hydrotalcites were determined by X-ray diffraction and FTIR spectroscopy. On calcination at 600 °C the materials were transformed into mixed metal oxides. The kind of the counterbalancing anions present in the parent hydrotalcite influences strongly textural parameters of the obtained Mg-Al oxides. Both temperature-programmed desorption of NH₃ and CO₂, and test reaction of 2-methyl-3-butyn-2-ol (MBOH) conversion were used to determine the acidity and basicity of the samples. The hydrotalcite derived mixed Mg-Al oxides showed the presence of Brønsted and Lewis acid and base sites. However, the strong basic character of the solids caused that acetone and acetylene were observed as the major products of MBOH conversion.     

The reaction of ceria coatings on mica with H2S: An in-situ X-ray diffraction study

Thin layers of ceria were deposited on the surface of mica platelets in solution. The reaction of such particles with hydrogen sulfide yields a red colored special effect pigment. The ceria layer reacts with H₂S to produce a variety of sulfide and oxysulfide phases. The reaction path discovered in situ by time and temperature resolved X-ray diffraction is CeO₂→CeS₂→C-Ce₂S₃→Ce₁₀S₁₄O. The reaction itself is extremely variable depending on gas flow, heating rates and decomposition atmospheres. Effects on the thin film are recorded by scanning electron microscopy (SEM) and revealed a destruction of the layer once red Ce₁₀S₁₄O was formed. The product layer then reveals the typical nonwetting behaviour of a liquid on a surface.     

Effects of Ca and Zr substitution upon structure and properties of Ba5LaTi3Ta7O30 low-loss dielectric ceramics

Effects of Ca and Zr substitution upon the dielectric properties of Ba₅LaTi₃Ta₇O₃₀ ceramics were investigated together with the structural characterization. All the samples of Ba₅La(Zr_xTi_1−x)₃Ta₇O₃₀ formed a filled tungsten-bronze structures, whereas the solid solution limit was determined as x=0.25 in (Ca_xBa_1−x)₅LaTi₃Ta₇O₃₀. Beyond this limit secondary phase of CaTa₂O₆ was detected and it would become the major phase for the Ca-rich compositions. The temperature coefficient of dielectric constant was improved with increasing Zr content while the dielectric constant decreased and the low dielectric loss varied little (in the order of 10⁻⁴). In the case of (Ca_xBa_1−x)₅LaTi₃Ta₇O₃₀, small temperature coefficient of dielectric constant could be obtained with increasing Ca content while the dielectric constant decreased significantly, and a small amount substitution of Ca for Ba induced decrease in dielectric loss.     

A comparative study of the gas sensing behavior of nanostructured nickel ferrite synthesized by hydrothermal and reverse micelle techniques

A comparative study of gas sensing behavior of nanocrystalline nickel ferrite synthesized by micro-emulsion and hydrothermal method to liquefied petroleum gas (LPG) is presented. Nanocrystalline nickel ferrite synthesized by hydrothermal method indicated higher electrical conductivity and gas sensitivity at low operating temperature compared to nanocrystalline nickel ferrite synthesized by reverse micelle technique. This difference in the gas sensing behavior can be attributed to the presence of more oxygen vacancies (i.e. non-stoichiometry) in the hydrothermally synthesized nickel ferrite. Incorporation of palladium had a catalytic effect and the operating temperature was significantly reduced in both the samples. The higher operating temperature of the reverse micelle nickel ferrite material makes the sensor response speed faster (∼10 s) compared to the hydrothermally synthesized material (∼1 min).     

Synthesis of LiFePO4 with fine particle by co-precipitation method

LiFePO₄ is a potential candidate for the cathode material of the lithium secondary batteries. A co-precipitation method was adopted to prepare LiFePO₄ because it is simple and cheap. Nitrogen gas was needed to prevent oxidation of Fe²⁺ in the aqueous solution. The co-precipitated precursor shows the high reactivity with the reductive gas, and the single phase of LiFePO₄ is successfully synthesized with the aid of carbon under less reductive conditions. LiFePO₄ fine powder prepared by co-precipitation method shows high rate capability, impressive specific capacity and cycle property.     

Effects of gallia additions on sintering behavior of gadolinia-doped ceria

The effects of gallia additions on the sintering behavior of gadolinia-doped ceria were systematically investigated from the following aspects: the variation in sintered density, the variation in grain size, and the existing forms of Ga₂O₃ in CeO₂.Sintered density increased with increasing Ga₂O₃ content up to 5 mol.% and then it decreased with further addition of Ga₂O₃. Grain size also increased with increasing Ga₂O₃ content up to 5 mol.% and then decreased with further addition of Ga₂O₃. Decrease in grain size was caused by a pinning effect of Ga₂O₃ precipitation at grain boundaries. Lattice constant decreased with increasing Ga₂O₃ content up to 5 mol.%. This decrease will be due to the substitution of smaller Ga³⁺ ions for Ce⁴⁺ ions in the CeO₂ structure. According to the results obtained from scanning electron microscope (SEM) and X-ray diffraction (XRD) analyses, the solubility limit of Ga₂O₃ in Ce_0.8Gd_0.2O_1.9 ceramics can be estimated to be nearly 5 mol.%. The addition of Ga₂O₃ up to the solubility limit was found to promote the sintering properties of Gd₂O₃-doped CeO₂.     

Electrical conductivity and gas sensitivity of Zn-Sb-O thick films

The thick film of Zn-Sb-O was prepared by coating the paste of nanoparticles mixture (Sb₂O₃:ZnO=1:3) on the alumina substrate, followed by sintering at 500-900 °C for 2 h in air. The electrical resistance and gas-sensing properties to benzene, alcohol and acetone of Zn-Sb-O films were found to be dependent on the change of phase structure caused by sintering temperature.