NCFW专家系统的汉语接口

NCFW系统是适合于花岗岩与变质岩地区的勘探地下水专家系统，系统的人机交互既可用菜单（亦称项目单）方式，亦可用汉语对话方式。这两种方式既可混合使用亦能灵活切换。本文着重描述了汉语接口的设计思想、实现中采用关键技术以及系统运行实例。     

英台地区天然水驱油藏的开发特点及稳产技术

掌握边底水运动规律，控制并利用活跃的边底水能量，是成功开发天然水驱油藏的关键。英台地区的英台、四方坨子和一棵树等三个油田均为天然水驱油藏，天然能量充足。油藏投入开发后初期含水较高，含水上升极快，造成产油量大幅度递减。针对其开发特点，适时采用大泵、电潜泵提液强采，通过大量补孔层间接替以及加密调整和扩边等稳产技术措施，确保了油藏以3％-5％的采油速度长期稳产，水驱采收率高达50％以上。     

2#板坯连铸机振动台故障分析及改造

论述了银山型钢有限公司炼钢厂2#板坯连铸机自投产以来其振动台存在的问题，根据实际情况分析论证并进行改造实施，实施后效果明显。     

Study of Liquid Phase Shifter for ICRF on EAST

A method of current drive with Ion Cyclotron Range of Frequency （ICRF） on Experimental Advanced Superconducting Tokomak （EAST） is described. A variety of liquid silicon oil heights in the phase shifter will bring the phase difference to the current drive. It is found that the current drive can be achieved by using the phase shifter. The liquid phase shifter is one of the impedance matching systems too.     

高分子量阴离子型聚丙烯酰胺的制备

介绍了聚丙烯酰胺的品种、性能及用途；研究了以丙烯酸为共聚单体，采用反相乳液聚合制备高分子量阴离子型聚丙烯酰胺胶乳的原理和方法；分析讨论了原料纯度、乳化剂和引发剂种类及操作条件等因素对产品性能的影响．     

Series resonant ZCS‐PFM DC‐DC power converter with high‐frequency high‐voltage transformer link for high‐power magnetron drive

This paper presents a single lossless inductive snubber‐assisted ZCS‐PFM series resonant DC‐DC power converter with a high‐frequency high‐voltage transformer link for industrial‐use high‐power magnetron drive. The current flowing through the active power switches rises gradually at a turned‐on transient state with the aid of a single lossless snubber inductor, and ZCS turn‐on commutation based on overlapping current can be achieved via the wide range pulse frequency modulation control scheme. The high‐frequency high‐voltage transformer primary side resonant current always becomes continuous operation mode, by electromagnetic loose coupling design of the high‐frequency high‐voltage transformer and the magnetizing inductance of the high‐frequency high‐voltage transformer. As a result, this high‐voltage power converter circuit for the magnetron can achieve a complete zero current soft switching under the condition of broad width gate voltage signals. Furthermore, this high‐voltage DC‐DC power converter circuit can regulate the output power from zero to full over audible frequency range via the two resonant frequency circuit design. Its operating performances are evaluated and discussed on the basis of the power loss analysis simulation and the experimental results from a practical point of view. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 153(3): 79–87, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20126     

Drying of Prone to Twist Boards in a Pre-Twisted Position

A method to minimize twist has been investigated; i.e., drying the boards in a pre-twisted position. It has been found that Norway spruce boards can be deformed toward straightness by this method. The force exerted by a board on its holders during drying in a pre-twisted position has been measured. When the variation in torsional stiffness as a function of temperature and moisture content is accounted for, it is found that a creep deformation of the board occurs both during the drying phase and the cooling phase. In addition to mechano-sorptive creep, a deformation released by a change in temperature also seems to occur.     

第十九讲 电机控制集成电路的选用二相步进电机驱动电路SAA1042的选用

MOTOROLA公司生产的SAA1042芯片用来控制并驱动二相步进电机，文中对其主要特点，引脚功能，技术指标，典型应用等作了介绍。     

A sensing strategy for the reverse engineering of machined parts

The reverse engineering of machined parts requires sensing an existing part and producing a design (and perhaps a manufacturing process) for it. We have developed a reverse engineering system that has proven effective with a set of machined parts. This paper describes the system, presents some results, and discusses strategy for a new system.This work was supported by ARPA under ARO grant number DAAH04-93-G-0420, DARPA grant N00014-91-J-4123, NSF grant CDA 9024721, and a University of Utah Research Committee grant. All opinions, findings, conclusions or recommendations expressed in this document are those of the authors and do not necessarily reflect the views of the sponsoring agencies.     

Preparations of nanosized TiO2 in reverse microemulsion and their photocatalytic activity

Nanosized titania sol has been produced by the controlled hydrolysis of titanium tetraisopropoxide (TTIP) in sodium bis(2-ethylhexyl)sulfosuccinate (AOT) reverse micelles. The physical properties, such as surface area, crystallite size and crystallinity according to R and W₀ ratio, have been investigated by TEM, XRD, BET, FT–IR, TGA and DTA. In addition, the photocatalytic decomposition of p-nitrophenol has been studied by using a batch reactor in the presence of UV light in order to compare the photocatalytic activity of prepared nanosized titania. It is shown that the anatase structure appears in the 300–600 °C calcination temperature range and the transformation of anatase into rutile starts above 700 °C. The crystallite size increases with increasing R and W₀ ratio but W₀ ratio shows a stronger effect on the crystallite size than R ratio. In the photocatalytic decomposition of p-nitrophenol, the photocatalytic activity is mainly determined by the crystallinity of titania. In addition, the titania calcined at 500 °C shows the highest activity on the photocatalytic decomposition of p-nitrophenol() and the pure anatase structure.