在线磨辊辊面粗糙度的实验研究

影响轧辊表面粗糙度的因素很多，为此对影响辊面粗糙度的因素进行了系统分析和实验研究，得出了轧辊和砂轮的速度、砂轮粒度、砂轮直径及磨削液等主要因素对轧辊表面粗糙度影响的一般规律。利用回归分析的方法建立了轧辊表面粗糙度的数学模型，并将计算值与实测值进行了比较，发现两者基本一致。此项研究为适时控制冷轧带钢在线磨辊辊面粗糙度提供了计算模型。     

Gloss Properties and Surface Morphology Relationships of Fruits

Eggplants exhibited a higher average gloss reading (15.3 Gloss Units (GU)) than mature green tomatoes (12.0 GU) and apples (8.2 GU) using a flat surface glossmeter. The same trend was observed using a novel curved surface glossmeter. Scanning electron micrographs revealed that epicuticular wax covering eggplants had a smoother structure than that of tomatoes and apples, providing a more effective light scattering surface. Wax removal resulted in decreases in gloss, with average readings of 9.5, 7.4 and 6.3 GU for eggplants, tomatoes and apples, respectively. These results indicate the extent to which wax may influence shininess, although roughness measurements of flattened peel after wax removal suggest that surface topography also influences gloss.     

接触传热表面粗糙度曲线的统计特征

测量了一般机械加工表面的轮廓曲线，基于小波变换提取了粗糙度曲线，分析了轮廓高度和接触峰高度的统计分布特征。研究结果表明，轮廓高度不服从严格的正态分布，但具有一定的正态性，而接触峰高度的统计特征与其评定标准有直接的关系。因此，对于接触热阻的计算模型来说，接触点数的计算应以合理选取接触峰的评定标准为前提。     

表面粗糙度的自动确定

根据零件精度，在CAD系统中能够快速、准确地自动确定其表面粗糙度，从其间接关系上分析并推导出了一套实用的换算公式，并使用在某CAD中。     

溢流反弧段水流边界层有关概念的探讨

本文对溢流反孤段水流边界层的定义方法进行分析讨论。在分析及弧段流速分布的基础上提出离心力附加边界层厚度和粗糙度附加边界层厚度的概念,研究了壁面曲率和壁面粗糙度对溢流反弧段边界层发展的影响。     

非接触型光外差轮廓仪

本文介绍一种纳米级非接触型高精度光外差轮廓仪,它是基于普通光路的光外差干涉仪。工件表面被两束有微小频差的激光束所照射,其中一束经聚焦后用作测量光探针来扫描工件表面,另一束则用作参考光束。两束光经表面反射后产生干涉。测量信号和参考信号的相位差与表面的微不平值成正比。仪器的横向分辨率为2μm,高度分辨率为1 nm,它不需要对试样作大范围的调整,且可用试样自身作参考面。信号经光电转换后由微型计算机进行处理,它能快速完成测量、计算、显示及打印出各种参数和曲线。     

Chemical-mechanical polishing of SiO2 thin films studied by X-ray reflectivity

Specular X-ray reflectivity from SiO₂ thin films prepared on silicon substrates by plasma-enhanced chemical vapor deposition showed the films to have a characteristic width of the decay in density at the free surface of 17 Å, to be about three-quarters the density of -quartz, and to have an interfacial layer at the silicon interface that was of the order of 100 Å wide and less dense than the bulk of the film. After chemical-mechanical polishing the characteristic width of the decay in density at the free surface was reduced to 10 Å; furthermore, the near-surface region to a depth of 30 Å had a greater density than the as-deposited film. Off-specular reflectivity confirmed that the decrease in characteristic width at the free surface was due to reduced roughness upon polishing and also revealed that the lateral correlation length in the limit of long wavelengths was the same for both polished and unpolished samples. The compression of the near-surface region during polishing is believed to enhance the dissolution of SiO₂ into the slurry which is necessary to achieve smooth surfaces.     

In-situ birefringence microscopy of uniaxially stretched metal-polymer laminate

This paper concentrates on revealing the local deformation as a function of applied strain in a polymer coating supported by a plastically deforming and roughening metal substrate. To this end in-situ birefringence microscopy measurements have been executed. The measurements are performed in reflection and an alternative unwrapping scheme for the optical path difference is proposed. From the characterization of PET (polyethylene terephthalate) coated stainless steel it is concluded that strain localization appears below the macroscopic strain at yield and that the surface roughness of the substrate is the driving force of the localization.     

电镀锡机组软熔导电辊脱锡技术研究

粘锡是电镀锡机组软熔导电辊失效的主要原因,应用化学方法脱锡是延长导电辊寿命的重要途径.开发了氢氧化钠(钾)为主要组成,并加入适量亚铅酸钠(钾)和硝酸(亚硝酸)钠配制而成脱锡剂,当脱锡剂温度为40～80℃,导电辊表面温度为40～70℃时,对粘锡导电辊具有很好的脱锡效果.粘锡导电辊脱锡后的表面粗糙度可以恢复到4.0μm以上,导电辊使用寿命提高80%,降低导电辊修复成本90%,并大幅度减少导电辊更换时间,提高电镀锡机组生产作业率.     

相干光被粗糙表面散射后衍射谱的分布探讨

利用傅立叶光学的基本原理，对相干光波被粗糙表面散射后衍射谱的分布进行探讨。