A complete VARMA modelling methodology based on scalar components

Abstract. This article proposes an extension to scalar component methodology for the identification and estimation of VARMA models. The complete methodology determines the exact positions of all free parameters in any VARMA model with a predetermined embedded scalar component structure. This leads to an exactly identified system of equations that is estimated using full information maximum likelihood.     

Compatibility between Polyamide 6 and Polycarbonate

Polyamide （PA6） and polycarbonate （PC） were prepared by a Brabender mixer （ PLV- 151） at 240℃ with 30 rpm for duration of 8 and 6 minutes respectively. The epoxy resin （E） addition can lead to substantial microstructural changes in the PA6/PC blends. Scanning electron microscope （SEM） was used to observe the mixtures characterized by the domains of clearly segregated homophases and voids between the two polymers. PA6/PC of polyamide 6 and polycarbonate with epoxy resin addition under the composition ratio of 20/80, 20/80/1, 40/60/1 and 40/60, were tested to verify the key role of epoxy in promoting the compatibility of PA6 with PC during blending.     

F2.4微孔膜的制备及在膜蒸馏过程中应用的初步研究

采用相转化法制备了F2 4的疏水微孔膜 ,并对F2 4和PVDF微孔膜的机械性能以及疏水性等方面进行了对比 .结果表明 ,F2 4微孔膜在拉伸时的应变以及断裂伸长率约为PVDF微孔膜的 6～ 9倍 ;其接触角 (77 4°)也大于PVDF膜的接触角 (6 6 7°) .尽管膜蒸馏的数据显示F2 4微孔膜的蒸馏通量尚不及PVDF膜 ,但通过调节各项制膜参数 ,F2 4可能具有良好的应用前景     

节能建筑中人体传热模型和计算公式

讨论人体新陈代谢发热率及其影响因素;论述节能建筑中舒适的环境温度、空气相对湿度、空气流速以及新鲜空气供给量的最佳值范围;同时考虑皮肤和肺部的显热散热和蒸发潜热散热,建立了传热模型,得出了计算公式。     

4F0.06AC树脂吹塑薄膜技术的探讨

在加工应用试验的基础上。探讨了加工温度、吹胀比、超想线高度及设备对４Ｆ０．０６ＡＣ薄膜适宜的加工条件。     

Design of a high-pressure ebulliometer,with vapor-liquid equilibrium results for the systems CHF2 Cl + CF3 CH3 and CF3 CH2 F + CH2F2

We describe the design and operation of a new high-pressure metal ebulliometer which can operate at pressures to at least 3 MPa in the range 220–400 K. Infinite-dilution activity coefficients are presented for the system CHF₂Cl + CF₃-CH, at 275 K and for the system CF₃-CH₂F + CH₂F₂, at 260, 230, and 300 K. The Wilson activity coellicient model and a virial coefficient model are applied to these systems, and the phase equilibrium conditions are calculated. The results are shown to agree well with predicted and with published measured values. The excess enthalpy is calculated and compared with results from a Peng Robinson equation of state. Vapor densities on the dew curves are given.     

一类三元线性分组码的译码

Ｐｌｅｓｓ［１］证明了三元（１２，６，６）Ｇｏｌａｙ码具有一种双层结构，并据此给出了该码的快速硬判决译码算法。本文推广了Ｇｏｌａｙ码的Ｐｌｅｓｓ结构，给出了由三元（ｎ，ｋ，ｄ）线性分组码构造的三元（３，ｎ＋ｋ，≥ｍｉｎ（ｎ，２ｄ，６））线性分组码，其中包括（１２，６，６）Ｇｏｌａｙ码和（１８，９，６）码，并以三元（１８，９，６）码为例给出了这类码的最大似然软判决译码算法。     

尼龙6表面金属(Ni)化膜材料的制备及性能研究

用化学还原法制得了尼龙６表面金属（Ｎｉ）化膜材料。研究了还原条件，金属盐浓度对膜材料电性能的影响，以及膜材料的电发热性能，用光电子能谱和扫描电子显微镜对其表面及形貌进行了表征。     

工业固体核磁Magmonitor用于聚烯烃质量参数测试方法的建立

利用实际采集的系列试样 ,在工业固体核磁Magmonitor(IMR)上建立了标准曲线 ;在IMR上运行标样的核磁信号后 ,对FID信号与实验数值之间的匹配使用 32个误差分析因子进行分析 ,并在Cregcon软件下运行回归分析 ,将结果转化成仪器预测模型。结果表明 ,测试相对偏差在 10 %以内 ,数据重现性好 ,而粉料与共聚物的测试误差有待改进。将IMR测试结果与不同测试方法进行比较 ,建议测试前对粉料进行脱气与脱水处理