宜昌站泄流能力变化对葛洲坝设计洪水影响

宜昌水文站是葛洲坝、三峡水利枢纽的设计依据站。葛洲坝水利枢纽动工修建和运行 ,对该站水位流量关系中低水部分产生了影响。探讨了该河段泄流能力的变化对葛洲坝水利枢纽设计洪水有无影响的问题。用1 967～ 1 999年实测资料对宜昌站以汛期平均水位为参数的水位流量关系曲线簇进行了检验 ,大部分年份最大日平均流量、3、7、1 5、30d洪量的偏差在± 4 %之间 ,说明曲线簇推流具有相当的精度。证明了宜昌河段中低水泄流能力的变化对葛洲坝水利枢纽设计流量和校核流量基本没有影响     

用离子束混合及快速热处理方法形成钽的硅化物

本文描述用离子束透过钽金属膜进行混合和快速热处理方法来形成钽的硅化物.用溅射方法在P型硅衬底上淀积一层金属钽,然后用砷离子束透过钽金属模进行混合,采用快速热处理后形成了平整的硅化钽薄层.使用厚度为500埃的钽金属膜,得到钽的硅化物薄层电阻为5.5Ω/□.研究了砷离子能量、剂量及钽膜厚度对钽的硅化物薄层电阻的影响.用透射电镜和台阶仪对所形成的硅化钽进行了分析和厚度测量.     

Machining with tool–chip contact on the tool secondary rake face—Part II: analysis and discussion

The forces, chip thickness, and natural tool–chip contact length in machining with a double-rake-angled tool are predicted in Part II of the present study. It is revealed that in comparison with a single-rake-angled tool, a double-rake-angled tool increases the forces, especially the thrust force. However, the increase in chip thickness and tool–chip contact length is not significant under the input conditions specified in the present study. The effect of seven input variables of the proposed model is quantitatively investigated. The predicted variations of forces, chip thickness, and natural tool–chip contact length are in good agreement with theoretical and experimental results obtained by other researchers. The interrelationships among the resultant force, the chip thickness, and the natural tool–chip contact length are established, which provides a new and promising method to estimate the tool–chip contact length by employing the resultant force. It is demonstrated that the model can also be extended to study the problem of machining with a groove-type chip breaker tool.     

长江口北支水道水沙特性分析

从实测资料出发,结合水流数值计算成果,对长江口北支水道的水流、泥沙和含盐度等资料进行分析,得出了北支水道的水沙特性,并分析了水沙变化与河床变化的相互关系.北支水道在1958年南通河段河势控制后,径流分流比逐年下降,并渐趋稳定于3%左右.北支水道受径流影响越来越小,主要受潮流作用.随着水沙特性的逐年变化,北支水道0 m以下槽蓄容量逐年减小,并渐趋稳定,北支上段为逐年淤积最快的区域.由此反过来影响了水沙条件的进一步变化,使北支上段平均潮差增加,北支的会潮点由崇头附近下移至青龙港附近.     

Influence of process variables on the drying of potato slices

Investigation of the effects of varying air velocity, slice thickness, and pre-treatment with sodium chloride solutions and surface active agents on drying potato slices indicated that the drying occurred entirely in the falling rate period and was controlled by the mechanism of liquid diffusion. The rate of drying, and therefore the diffusion coefficients, increased with the addition of sodium chloride and surface active agents. Diffusion coefficients were also influenced by air velocity and slice thickness, suggesting that the rate of drying of potato slices is controlled by a combination of internal and external resistances.     

冲击回波法检测隧洞混凝土衬砌厚度

冲击回波法是通过接收、分析在混凝土中传播的回波信号，判断结构混凝土厚度和内部质量的新型无损检测技术。室内试验和工程应用研究表明，该方法为隧洞混凝土衬砌厚度检测提供了一个有效的测试手段。     

Simultaneous HPLC quantification of total cholesterol,tocopherols and β-carotene in Barrosã-PDO veal

A simple, rapid and sensitive procedure for the simultaneous determination of total cholesterol, tocopherols and β-carotene in meat is described. The method involves a direct saponification of the meat, a single n-hexane extraction and the analysis of the extracted compounds by normal-phase HPLC, using fluorescence (tocopherols) and UV–Vis photodiode array (cholesterol and β-carotene) detections in tandem. Rates of recovery of spiked meat samples were 93% for cholesterol, 83–86% for (α-, β- and -γ) tocopherols and 89% for β-carotene. Repeatabilities were high (CV < 6%) for all determined compounds, except for δ-tocopherol. This tocopherol, which is not usually present in meat, showed a much lower recovery percentage (73%) and repeatability (12.8%). This methodology was applied for the quantification of total cholesterol, tocopherols and β-carotene in three muscles (longissimus thoracis, longissimus lumborum and semitendinosus) of the Portuguese traditional Barrosã-PDO veal, obtained from autochthonous calves fed extensively during summer (with the least abundant green pastures) and slaughtered in early autumn (October). Barrosã-PDO veal showed median contents of total cholesterol (0.50–0.56 mg/g) and, depending on the analysed muscle, moderate to high contents of α-tocopherol (3.3–3.9 μg/g) and β-carotene (0.07–0.09 μg/g), suggesting an high sensorial and hygienic quality.     

Flexural and Shear Rigidity of Composite Sheet Piles

The flexural and shear rigidity of pultruded composite sheet pile panels consisting of E-glass fiber-reinforced polyester are studied in this paper. The analysis consists of an experimental investigation and an analytical modeling to determine the resistance of the sheet pile panels to the deflections for design of composite sheet pile walls. Timoshenko’s beam theory was used to experimentally determine the flexural rigidity (EI) and shear rigidity (kAG) of the panel. Three- and four-point bending tests were performed on six different span lengths and the results were self-compared from the two independent tests. Analytical expressions for the flexural and shear rigidities were derived to allow the prediction based on the layered structure of pultruded shapes. The values computed from the analytical expressions were examined with the experimental results.     

Substantiation of Application of Overburden Rehandling in Flat-Dipping Deposits

The layer reexcavation ratio is proposed to use for determination of overburden thickness in the combined conveying and direct-dumping systems of mining by draglines with haulage to goaf. It is established that this method ensures the decrease in costs of mining the horizontal and flat-dipping deposits.     

Composite scale modeling in the presence of censored data

A composite scale modeling approach can be used to combine several scales or variables into a single scale or variable. A typical application is to combine age and usage together to form a composite timescale model. The combined scale is expected to have better failure prediction capability than individual scales. Two typical models are the linear and multiplicative models. Their parameters are determined by minimizing the sample coefficient of variation of the composite scale. The minimum coefficient of variation is hard to apply in the presence of censored data. Another open issue is how to identify key variables when a number of variables are combined. This paper develops methods to handle these two issues. A numerical example is also included to illustrate the proposed methods.