电子设备的电磁屏蔽设计

针对电子设备的特点,提出了电子设备电磁屏蔽设计的基本原则,从缝隙、孔洞、电缆以及搭接4个方面详细论述电磁屏蔽的各种措施。     

一种适用于GSM DCS和ISM频段的PIFA天线

移动通信业务的多样化要求多种业务共用一副天线,以节省终端内的有限空间。在平面倒F天线(PIFA)的基础上加载一种新型的缝隙结构,得到一种适用于GSM900、DCS1800和ISMWLAN2.4GHz三个频段的小型宽带移动终端天线。仿真结果表明,该天线在三个频段上的相对阻抗带宽分别达到6.5%、7.5%和3.4%,尤其是在GSM900MHz频段的阻抗带宽比其他同类型天线展宽1倍。该天线具有较好的频率特性和辐射特性,完全适合多频移动通信终端应用。     

盲槽孔板的设计及加工方法探讨

文章主要针对盲槽产品的制作流程及加工方法的控制作探讨,盲槽孔主要是利用已经钻好槽孔板和半固化片与另一张板进行压合形成。压合盲槽板时半固化片上所钻的槽孔大小设计/品质及半固化片本身流胶量严重影响成品盲槽的品质,本次主要以影响盲槽孔品质的几个因素作实验层别:半固化片槽孔大小分别比成品槽孔单边大0.4mm、0.6mm、0.8mm;PP厚度0.0375mm×3张;PP铣槽孔时叠板数为6、9、12。结论:半固化片槽孔单边大0.8mm最优,1.5mil厚的PP铣板叠板数9张时铣出的PP压合后槽孔品质符合要求,叠板数越少铣槽的效果越好;介层总厚度相同时,PP选用的张数越少压合时流胶越少,盲槽孔孔形越好。     

低剖面渐变槽线天线单元设计

基于有限元仿真软件通过设置周期性边界条件的方法,分析了影响渐变开槽天线单元宽带宽角扫描性能的关键因素。通过在安装天线阵列的反射面上铺覆新型阻抗匹配材料,克服了天线高度对驻波带宽的限制,实现了天线的小型化设计。加工制作了一个20×16天线单元的实验小型面阵,并对其有源扫描驻波进行了测试。实测结果与仿真结果吻合,表明该天线在8GHz～12GHz带宽内±45°扫描范围内性能优异,可广泛应用于宽带宽角扫描相控阵天线系统。     

通信基站RRU主板制作方法研究

介绍一种通信基站RRU主板的制作方法,重点研究过孔离PTH槽较近时树脂塞孔容易产1 " 生残胶问题,负片流程制作超大异形PTH半孔槽及长条形PTH孔干膜封孔问题,PTH半孔槽预防成型批锋等问题。     

COUPLING PROPERTIES OF THE SLOT IN A WAVEGUIDE JUNCTION

The coupling properties of a transverse slot in the common wall between two buttingrectangular waveguides are discussed.By means of Galerkin's method which takes into accountthe wall thickness,equivalent magnetic currents on the aperture surface of the slot are obtained,and then the general formulae of scattering fields and of equivalent parameters are derived.Thedimensions as well as seats of those two waveguides and the slot,and the thickness of the wall arearbitrary.For example,the transforming coefficients and the VSWRs of numerical calculationand experimental results are given.They are in good agreement.     

The Rectangular Waveguide Board Wall Slot Array Antenna Integrated with One Dimensional Subwavelength Periodic Corrugated Grooves and Artificially Soft Surface Structure

In this letter, we propose a high gain rectangular waveguide board wall slot array antenna, which is integrated with one dimensional subwavelength periodic corrugated grooves and artificially soft surface structure. The corresponding far field radiation characteristics are investigated. The simulation results show that the gain of planar 2 × 8 slot array antenna with the introduction of corrugated grooves structure is increased to 26.1 dB, and half power beamwidth in the E plane is considerably reduced. Compared with the subwavelength periodic grooves slits array antenna proposed by Huang et al.[Appl. Phys. Lett. 91, 143512 (2007)], the side and back lobe level of this antenna are also significantly reduced by 6 dB and 10 dB, respectively. The physical mechanism for radiation-pattern improvement has been well explained by the modulation of surface wave, the reradiation of surface energy, and suppression of surplus surface wave at the grounded edge.     

Recent progress of catalyst ink for roll-to-roll manufacturing paired with slot die coating for proton exchange membrane fuel cells

Roll-to-roll (R2R) manufacturing paired with slot die coating is a promising route to realize the mass production of catalyst layers of proton exchange membrane fuel cells and achieve a sharp decrease in manufacturing costs through scale effect. Catalyst ink runs through the route and governs the ultimate structure of catalyst layer. Therefore, designing and preparing an optimal high-solid content catalyst ink and figuring out how to utilize it well in the R2R process has become a significant challenge. Herein, recent progress in catalyst ink is focused on design, preparation, rheology, slot die coating, and drying process. This review is a significant step forward in providing fundamental knowledge and understanding of the nature of advanced catalyst ink and its compatibility with the R2R process which are essential for designing and manufacturing excellent catalyst layers.     

Operability coating windows and frequency response in slot coating flows from a viscocapillary model

Slot coating, indispensable to the manufacturer of flat panel displays and long-life secondary batteries, can be susceptible to unexpected disturbances at high speeds, leading to many kinds of undesirable defects. Operability coating windows for both Newtonian and non-Newtonian (shear-thinning) liquids have been investigated using a simplified viscocapillary model in a slot coating bead flow regime. Stable coating windows, free from leaking (or dripping) and bead break-up, have been determined by the position of upstream meniscus. They quantitatively coincided with those from two-dimensional calculations by a CFD Fluent solver. The pressure range that allowed a stable bead widened as the viscosity of the coating liquid or the capillary number in downstream die region increased. Also, the sensitivity of the slot coating flow through frequency response method was tested by measuring the amplitude of final wet coating thickness with respect to ongoing sinusoidal disturbances at different frequencies imposed to web speed, flow rate, bead pressure and coating gap. The viscocapillary model was compared with a 2D model and was found to be a fast and efficient tool that could enhance the productivity and processability of coating systems.