糖厂现用连续离心机的研究及生产实践

在各糖厂现用连续离心机原有生产实践基础上，对其机械吸震、加温、布温、机索结构、物料密封、机座等部件做了进一步改进，并取得可观的实效。     

Mathematical modeling of falling liquid film evaporation process

A mathematical model of evaporation process from a laminar falling liquid film on a vertical plate of constant temperature is presented. The model is developed with and without interfacial shear stress due to the vapor flow at the liquid film surface. The vapor pressure drop, vapor exit velocity and cooling rate are calculated for different liquid mass flow values. It is shown that lower liquid mass flow produces higher cooling rate. The results also show that the interfacial shear stress has a considerable negative effect on the cooling rate. It is proved that there exists an optimum distance between the plates, which gives the maximum volumetric cooling rate.     

Sol-gel Preparation and Preliminary in vitro Evaluation of Fluorapatite／Hydroxyapatite Solid Solution Films

Fluorapatite/hydroxyapatite solid solution has better biological properties than other apatites, especially used as films or coatings. In this work, sol-gel preparation and in vitro behavior of fluorapatite/hydroxyapatite solid solution films on titanium alloy were investigated. Ca(NO3)2-4H20 and PO(OH)x(OEt)3-x were selected as precursors, and hexafluorophosphoric acid (HPFo) was used as a fluorine containing reagent. The Ca and P precursors were mixed with HPFo to keep the Ca/P molar ratio 1.67. The mixtures refluxed for 12 h were used as dipping sols for the preparation of the films. The phase of the films obtained at 600℃ was apatite. The F contents in the films increased with the concentrations of HPF6 in the dipping sols. The solid solution films were shown to have better stability than hydroxyapatite films, and a reasonably good bioactivity in the in vitro evaluation.     

化学束外延

本文介绍了化学束外延(CBE)的发明和发展,论述了CBE的原理和设备。文中还介绍了最近提出的一种生长机理。     

应用多孔阳极氧化电流—时间曲线比较壁垒膜厚

在有壁垒膜存在的表面,多孔膜的生长在氧化初期受到延迟阻碍,这一现象在直流恒压多孔阳极氧化电流一时间曲线上反映出来。电流达到稳态氧化的时间愈长,壁垒膜愈厚。文中应用此法判断了0.5MH_3BO_3介质的pH值、温度对壁垒阳极氧化膜厚的影响,并应用记录同一介质环境壁垒恒流阳极氧化的槽压一时间曲线得到验证。     

固体润滑涂层的评价和使用

本文主要介绍了二硫化钼，石墨、聚四氟乙烯三种固体润滑涂层的特点以及润滑涂层摩擦磨损性能的评价手段和方法，以及台架试验和应用实例，提出了选用方法和步骤。     

Microcalorimetry for characterization of film formation and cure of coatings and adhesives

A new microcalorimeter with eight parallel channels using robust, low cost sensors for characterization of coatings and adhesives is described and first experiments on coatings and adhesives are presented. The calorimetric sensors are based on thin glass plates (20 mm × 20 mm, thickness 150 μm) with heater and thermocouple sputtered on the surfaces (calorimetric active area of about 9 mm²). The setup allows heating and cooling experiments as well as isothermal measurements in the temperature-modulated mode with up to eight sensors in parallel. The measured quantities are the real (C^′_p) and imaginary part (C^″_p) of the complex heat capacity (), the related absolute value of the heat capacity () and the heat flow . An industrial computer (NI PXI system) with specific software for calibration and data recording controls the electronic components. Sensors can be embedded in a temperature controlled oven (heating and cooling by Peltier elements) or alternatively in a climatic cabinet with controlled temperature and humidity.

The method has been applied successfully to monitoring of film formation of aqueous polymer dispersions (styrene-acrylate copolymer) and curing of coatings.     

Hydrodynamic force between two hard spheres tangentially translating in a power-law fluid

The hydrodynamic interaction between two hard spheres tangentially translating in a power-law fluid is investigated. By considering the gap between the two spheres being sufficiently small such that the Reynolds’ lubrication theory applies, an analytical equation to the pressure in the gap is obtained using truncated Fourier series. To a good approximation, the pressure equation can be further simplified. The simplified approximate equation over-predicts the pressure for shear thickening fluid (n>1) but under-predicts the pressure for shear-thinning fluid (n<1). However, the errors in the predicted tangential force and moment are relatively small. In particular, for a Newtonian fluid, the accurate solution and the simplified approximate solution degenerate to the asymptotic solution of Goldman et al. [1967. Slow viscous motion of a sphere parallel to a plane wall-motion through a quiescent fluid. Chemical Engineering Science 22, 637-651.] and O’Neill and Stewartson [1967. On the slow motion of a sphere parallel to a nearby plane wall. Journal of Fluid Mechanics 27, 705-724.]. Both solutions predict that for shear thickening fluid (n>1), the hydrodynamic force converged in the inner region of the gap between the two spheres and the contribution from the outer region is sufficiently small. For shear thinning fluid (n<1), the contribution from the outer region is also significant.     

Emission Of Volatile And Semivolatile Organic Compounds From Waterborne Paints – The Effect Of The Film Thickness

A waterborne paint was applied to tin plated steel sheets with three different film thicknesses. The emission of volatile and semivolaile organic compounds ((S) VOCs) from the samples was measured in small climatic chambers under standard conditions over a two-week period. The purpose of the study was to evaluate the effect of the film thickness on the emission rate decay. First order decay models, including sink effects for the high boiling (S) VOCs, were fitted to the concentration versus time data. The results showed that the first order rate constants decrease with increasing film thickness. In uddition, the results indicated that the emissions of the (S)VOCs in the waterborne paint film seemed to be controlled by evaporation. The thicknesses of paint films used in climatic chamber tests to estimate emission rates for product compurison or emission prediction must be known in order to prevent erroneous conclusions     

旋转式伽玛刀的辐射剂量学

旋转式伽玛刀的辐射剂量学指标的物理测试在放射性医疗设备投放医院正式临床使用前是必不可少的，是对设备及其附件的设计、加工制造、安装以及电气控制系统等的全面综合性检定。用电离室作辐射剂量学的绝对测量，用胶片法进行相对测量，给出了测量结果并进行了讨论。