Photoelectrochemical properties of sol–gel-derived Ti1−xVxO2 solid solution film photoelectrodes

Ti_1−xV_xO₂ solid solution film photoelectrodes were prepared by the dip-coating sol–gel method. X-ray diffraction and X-ray photoelectron spectroscopy were employed to ensure the formation of the solid solution and their composition. Obvious photoresponses were observed in the visible region for the solid solution film electrodes with x0.05 and the red shift of the photoresponse was enhanced with increasing x. Moreover, the solid solution film electrodes were found to be photoelectrochemically stable. However, the onset potential of photocurrent shifted positively with increasing x. Band model of the solid solution was suggested to explain the effects of the vanadium incorporation on the photoelectrochemical properties.     

固体润滑涂层的评价和使用

本文主要介绍了二硫化钼，石墨、聚四氟乙烯三种固体润滑涂层的特点以及润滑涂层摩擦磨损性能的评价手段和方法，以及台架试验和应用实例，提出了选用方法和步骤。     

Microcalorimetry for characterization of film formation and cure of coatings and adhesives

A new microcalorimeter with eight parallel channels using robust, low cost sensors for characterization of coatings and adhesives is described and first experiments on coatings and adhesives are presented. The calorimetric sensors are based on thin glass plates (20 mm × 20 mm, thickness 150 μm) with heater and thermocouple sputtered on the surfaces (calorimetric active area of about 9 mm²). The setup allows heating and cooling experiments as well as isothermal measurements in the temperature-modulated mode with up to eight sensors in parallel. The measured quantities are the real (C^′_p) and imaginary part (C^″_p) of the complex heat capacity (), the related absolute value of the heat capacity () and the heat flow . An industrial computer (NI PXI system) with specific software for calibration and data recording controls the electronic components. Sensors can be embedded in a temperature controlled oven (heating and cooling by Peltier elements) or alternatively in a climatic cabinet with controlled temperature and humidity.

The method has been applied successfully to monitoring of film formation of aqueous polymer dispersions (styrene-acrylate copolymer) and curing of coatings.     

Hydrodynamic force between two hard spheres tangentially translating in a power-law fluid

The hydrodynamic interaction between two hard spheres tangentially translating in a power-law fluid is investigated. By considering the gap between the two spheres being sufficiently small such that the Reynolds’ lubrication theory applies, an analytical equation to the pressure in the gap is obtained using truncated Fourier series. To a good approximation, the pressure equation can be further simplified. The simplified approximate equation over-predicts the pressure for shear thickening fluid (n>1) but under-predicts the pressure for shear-thinning fluid (n<1). However, the errors in the predicted tangential force and moment are relatively small. In particular, for a Newtonian fluid, the accurate solution and the simplified approximate solution degenerate to the asymptotic solution of Goldman et al. [1967. Slow viscous motion of a sphere parallel to a plane wall-motion through a quiescent fluid. Chemical Engineering Science 22, 637-651.] and O’Neill and Stewartson [1967. On the slow motion of a sphere parallel to a nearby plane wall. Journal of Fluid Mechanics 27, 705-724.]. Both solutions predict that for shear thickening fluid (n>1), the hydrodynamic force converged in the inner region of the gap between the two spheres and the contribution from the outer region is sufficiently small. For shear thinning fluid (n<1), the contribution from the outer region is also significant.     

Synthesis, Characterization, and Cytotoxicity Analysis of a Biodegradable Polyurethane

A polyester urethane was synthesized for use in a biodegradable scaffold. The polyurethane was synthesized in a two-step process: first, ester diol was synthesized from lactic acid and polyethylene glycol 400 (PEG 400), then it was polymerized with toluene diisocyanate using dibutyl tin dilaurate (DBTDL) as a catalyst to form a polyester urethane. Polyester urethane has tensile strength of 51-59 MPa and elongation at fracture of 369-439%. FTIR and XRD were used to confirm the formation and structure of the polymer. Hydrolytic degradation was studied in different alkali solutions and in saline water. In order to assess the cellular response of this material, cytotoxicity analysis was carried out against the cell line.     

Emission Of Volatile And Semivolatile Organic Compounds From Waterborne Paints – The Effect Of The Film Thickness

A waterborne paint was applied to tin plated steel sheets with three different film thicknesses. The emission of volatile and semivolaile organic compounds ((S) VOCs) from the samples was measured in small climatic chambers under standard conditions over a two-week period. The purpose of the study was to evaluate the effect of the film thickness on the emission rate decay. First order decay models, including sink effects for the high boiling (S) VOCs, were fitted to the concentration versus time data. The results showed that the first order rate constants decrease with increasing film thickness. In uddition, the results indicated that the emissions of the (S)VOCs in the waterborne paint film seemed to be controlled by evaporation. The thicknesses of paint films used in climatic chamber tests to estimate emission rates for product compurison or emission prediction must be known in order to prevent erroneous conclusions     

旋转式伽玛刀的辐射剂量学

旋转式伽玛刀的辐射剂量学指标的物理测试在放射性医疗设备投放医院正式临床使用前是必不可少的，是对设备及其附件的设计、加工制造、安装以及电气控制系统等的全面综合性检定。用电离室作辐射剂量学的绝对测量，用胶片法进行相对测量，给出了测量结果并进行了讨论。     

Cr/SiO_2界面还原反应研究

利用俄歇电子能谱研究了Cr／SiO2薄膜在热处理过程中的界面扩散反应机理、界面反应动力学过程及界面反应产物。研究结果表明，Cr／SiO2体系的界面还原反应主要是Cr与SiO2的反应，其还原反应产物是CrSix和Cr2O3物种。界面还原反应的速度与反应时间的平方根成正比，其界面还原反应过程受Cr向SiO2层的扩散过程所控制，界面还原反应的表观活化能为72．5kJ／mol（约0．75eV）。     

Characterization of CuInS2 thin films for solar cells prepared by spray pyrolysis

We have made a study of the chemical composition, the electrical, the optical and the structural properties of polycrystalline CuInS₂ thin films prepared by spray pyrolysis to be used for thin film solar cells. These films were deposited starting from aqueous solutions with different chemical compositions ([Cu]/[In] and [S]/[Cu] ratios) and at different substrate temperatures. In all cases, the material is p-type with grains preferentially oriented in the (112) direction of the sphalerite structure. The electro-optical properties show a very strong dependence on the [Cu]/[In] ratio in the solution. Films with copper excess have smaller resistivity and better crystallinity than those which are stoichiometric or have indium excess. The results obtained in this work show the possibility of having CuInS₂ thin films with a wide range of resistivity, a fact that could be important for making solar cells based on this material.     

Comparative Coreflood Studies for Precipitation and Adsorption Squeeze with PPCA as the Scales Inhibitor

Comparative adsorption and precipitation squeezes carried out on field core materials demonstrate that significant lifetime enhancement is achievable for precipitation squeeze with respect to more conventional adsorption squeeze. Coreflood tests have been carried out under reservoir conditions (135°C) employing a poly-phosphinocarboxylate (PPCA) as the scales inhibitor. Field treatment simulations, carried out starting from coreflood data and considering the characteristics of a North Sea formation taken as the reference, confirmed the higher performance, in term of squeeze lifetime, of the precipitation squeeze with respect to adsorption. The results pointed out the importance of choosing the appropriate formulation once the operative conditions are known, in order to promote the inhibitor precipitation into the formation. Some implications of these results for the optimization of the precipitation squeeze technology for field applications, with particular emphasis to formation damage, are also discussed.