Application of SiC-Si functionally gradient material to thermoelectric energy conversion device

Because of its high–temperature chemical stability, SiC ceramic is a promising material for high-temperature device applications such as thermoelectric energy converters. However, the electrical conductivity of SiC ceramic is too low for it to be used as a thermoelectric energy converter at the cold junction. Therefore, we propose a SiC-Si functionally gradient material (FGM) in order to improve the electrical conductivity of the SiC ceramic at the cold junction. An SiC rod was fired in a temperature gradient furnace. One end of the SiC rod was maintained at 2473 K and the other end was maintained at 1973 K for 30 min. After firing, the porous SiC edge fired at 1973 K was dipped into molten Si in order to infiltrate molten Si into the porous SiC. The microstructure of the FGM is classified into three regions: the SiC-Si composite material; the porous SiC ceramic; and the densified SiC ceramic. The electrical conductivity, the Seebeck coefficient and the thermal conductivity for each region of SiC-Si FGM was measured at 300 K; a figure of merit was calculated. The figure of merit of the SiC-Si FGM at the cold junction, at room temperature, was 10⁸ times higher than that of a nongradient SiC ceramic.     

A New Variable Diffusion Drying Model for the Second Falling Rate Period of Paddy Dried in a Rapid Bin Dryer

The objectives of this article is to propose a new drying model for the second falling rate period known as the variable diffusion controlled period that follows after the first falling rate period and to propose a new method to determine the second critical moisture content that separates these two periods. Experimental work on paddy drying at minimum fluidization velocity was carried out in a rapid bin dryer. The effects of operating temperatures (60-120°C) and bed depths (2-6 cm) on the paddy drying characteristics were investigated. It was found that the normalized drying rate of paddy was proportional to the normalized moisture content in the first falling rate period but in the second falling rate period, the normalized drying rate of the material varies exponentially with the normalized moisture content. The different relationship between the normalized drying rate and the normalized moisture content in the first and second falling rate periods indicate that two different mechanism of moisture transport are at work. The new exponential model of the second falling rate period and the linear model of the first falling rate period were found to fit the experimental data very well. Derivation from variable diffusion equation shows that the linear model is the result of constant diffusion coefficient whereas the new exponential model is the result of linear diffusion coefficient. This also implies that the first falling rate period is a constant diffusion controlled period and the second falling rate period is a variable diffusion controlled period. In addition, drying kinetics data of a drying process that fits the exponential model over a very slow drying period will show that the drying process is under the effect of a linear diffusion coefficient. It was also found that the proposed new method to determine the second critical moisture content that distinguishes between the first and second falling rate periods by using a sudden change in the value of the drying rate gradient to a much lower value at that point is more rigorous and yet simpler than the method of determining the specific location of the receding drying boundary since it is based on the behavior of the actual drying kinetic data.     

MIMO系统的自适应均衡技术研究

研究了用于MIMO系统的自适应均衡的几种算法，比较了最小均方算法(LMS)、递归最小二乘算法(RLS)、判决反馈算法(DFE)、格型梯度自适应均衡算法(GALE)和格型最小二乘自适应均衡算法(LSALE)。文章的最后给出了仿真结果及结论。     

浅谈冷库冲霜水系统中的防冻

分析了冷库冲霜水系统中所存在的冻结问题及解决方法。     

New approaches for error estimation and adaptivity for 2D potential boundary element methods

This work presents two new error estimation approaches for the BEM applied to 2D potential problems. The first approach involves a local error estimator based on a gradient recovery procedure in which the error function is generated from differences between smoothed and non‐smoothed rates of change of boundary variables in the local tangential direction. The second approach involves the external problem formulation and gives both local and global measures of error, depending on a choice of the external evaluation point. These approaches are post‐processing procedures. Both estimators show consistency with mesh refinement and give similar qualitative results. The error estimator using the gradient recovery approach is more general, as this formulation does not rely on an ‘optimal’ choice of an external parameter. This work presents also the use of a local error estimator in an adaptive mesh refinement procedure. This r‐refinement approach is based on the minimization of the standard deviation of the local error estimate. A non‐linear programming procedure using a feasible‐point method is employed using Lagrange multipliers and a set of active constraints. The optimization procedure produces finer meshes close to a singularity and results that are consistent with the problem physics. Copyright © 2002 John Wiley & Sons, Ltd.     

Increasing Raffinate Dewaxing Efficiency

The efficiency of dewaxing of wide and narrow distillation raffinates using different mixed solvents: acetone and methyl–tert–butyl ether (MTBE), acetone and toluene, methyl ethyl ketone (MEK) and toluene, is compared. Decreasing the cutpoints from 100–140 to 50–70°C increases the filtration rate by 2 and more times and the yield of dewaxed lube oil by 2.5–5% as a function of the solvent used.     

Solving regularized least squares with qualitatively controlled adaptive cross‐approximated matrices

The adaptive cross‐approximation (ACA) technique is applied to accelerating an inverse‐problem solver that estimates charge distribution on a dielectric spacer. The ACA generates an approximated system‐matrix that enables us to carry out high‐speed inverse calculation. We designed an approximation procedure based on ACA with some additional concepts, that is, (a) partitioning of matrix based on algebraic information, (b) approximation quality control based on matrix norms, and so on. The tested solver (LSQR for regularized least squares) with ACA demonstrates about 10 times faster performance than that without ACA. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 159(3): 10–18, 2007; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20326     

A physically based method for triangulated surface flattening

This paper introduces a new method of generating 2D flat patterns from a 3D triangulated surface by opening the bending configuration of each winged triangle pair. The flattening can be divided into four steps. First, a 3D triangulated surface is modeled with a mass-spring system that simulates the surface deformation during the flattening. Second, an unwrapping force field is built to drive the mass-spring system to a developable configuration through the numerical integration. Third, a velocity redistribution procedure is initiated to average velocity variances among the particles. Finally, the mass-spring system is forced to collide with a plane, and the final 2D pattern is generated after all the winged triangle pairs are spread onto the colliding plane. To retain the size and area of the original 3D surface, a strain control mechanism is introduced to keep the springs from over-elongation or over-shrinkage at each time step.     

应用磷灰石裂变径迹研究大民屯凹陷的古地温

为深刻认识辽河盆地古地温特征，利用裂变径迹分析方法，对大民屯凹陷钻井岩心中19块磷灰石样品的裂变径迹年龄和长度做了测试。结果表明，随井深增加，径迹年龄和平均径迹长度有减少、变短的显著趋势，ES3^4地层磷灰石裂变径迹表观年龄比地层年龄年轻得多，说明沉积后曾长时间处于退火带中，退火带古地温为74～130℃，有效加热时间为4l～45Ma，2300～4000m深度地层处于退火过渡带。将径迹长度分布特征与地史、热史模拟结果相结合，认为该区在ES4段末经历一次短时间迅速增温后，ES3^1亚段存在一个区域抬升降温的热事件过程，其后地层稳定下降，沉降幅度小、沉积物较薄，温度增加缓慢，古地温梯度高于今地温梯度，对生、排烃较为有利。     

直接斜率波前复原算法的控制效果分析

建立自适应光学系统功率谱抑制函数的概念，分析了采用直接斜率波前复原算法的自适应当光学系统的控制效果，理论分析与６１单元自适应光学系统上的实验结果表明，直接斜率波前复原算法将导致控制效果下降。