A single chip multi-channel surface plasmon resonance imaging system

A single chip, multi-channel surface plasmon resonance (SPR) imaging system has been developed. The equipment has no moving parts and uses a single sensor chip on which multiple channels can be incorporated. A light emitting diode is used as a photon source while a CCD camera forms the detector. The optical configuration has been designed to achieve a uniform illumination of the sample over a fixed area with a range of incident angles. A calibration test using sucrose solutions shows that the sensitivity of the equipment is 4.3×10⁻⁴ refractive index units per pixel line-pair. The use of the system for simultaneous interrogation of different polyelectrolyte thin films, formed by the electrostatic layer-by-layer deposition method, is demonstrated. A reversible pH-dependent response for these organic layers is also reported.     

C＋＋Bezier曲面类的构造

利用Ｃ＋＋面向对象的新特征，对Ｂｅｚｉｅｒ曲面的定义和生成过程进行封装，从而极大地简化了Ｂｅｚｉｅｒ曲面的定义和绘制过程。     

Polarization control scheme for surface plasmon and optical guided mode control detection

A technique based on what is known as polarizer–compensator–sample–analyzer (PCSA) scheme in ellipsometry, combined with the Kretschmann configuration to excite plasmon and waveguided modes is described. The system allows the control of the polarization state of the reflected light and is shown to have higher sensitivity than the measurement of only the amplitude of the reflected light. We show the response of the system to variations in temperature and small changes in the refractive index of a liquid.     

Determination of surface heat-transfer coefficients of steel cylinder with phase transformation during gas quenching with high pressures

In numerical simulation of quenching process, the boundary conditions of temperature field and stress field are very important, in which the boundary conditions of temperature field are very complicated. In order to simulate the thermal strains, thermal stresses, residual stresses and microstructure of the steel during gas quenching by means of the numerical method, it is necessary to obtain an accurate boundary condition of temperature field. The surface heat-transfer coefficient is a key parameter. The explicit finite difference method, non-linear estimate method and the experimental relation between temperature and time during quenching have been used to solve the inverse problem of heat conduction. The relationships between surface temperature and surface heat-transfer coefficient of cylinder have been given. The non-linear surface heat-transfer coefficients include the coupled effects between phase transformation and temperature. In calculation, physical properties were treated as the function of temperature and volume fraction of constituent. The results obtained have been shown that this technique can determine effectual the surface heat-transfer coefficients during gas quenching.     

Lanthanum Containing Polymer''s Modification to PP

Polypropylene (PP)'s low impact strength limits its usages. Adding some a rare earth polymer can enhance PP's tensile strength and impact strength. Acrylic lanthanum was prepared by the reaction between lanthanum oxide and acrylic acid. The IR spectrum prove that and optimum reacting conditions are that the bulk ratio of La(AA) 3 and MMA is not less than one and temperature is about 80 ℃. Lanthanum containing Polymer were added into PP. When percent of addition only was 3%, strength were enhanced 10% , and impact strength 40%. SEM shows the compatibility of rare earth polymer and PP; lanthanum containing polymer can form physical crosslinking between PP's molecules, then every particle's surface connect with several PP molecules and the PP mechanical property were enhanced.     

Effects of lubrication and humidity on the abrasiveness of a thin boron carbide coating

Studies using thin boron carbide (B₄C) coatings have previously been performed in order to investigate their potential use as finite-life run-in coatings. Such coatings have been shown to polish the mating surface in a relatively short time. The inherent ability of these coatings to polish can potentially allow them to function as finite-life run-in coatings. Employing such coatings requires a thorough understanding of the parameters which directly influence the changes that occur in the coating abrasiveness throughout the duration of the polishing process. In past studies, changes in the coating abrasiveness during dry sliding wear under ambient conditions have been investigated. However, both lubrication and humidity can strongly influence the abrasive wear process. In this study, the influences of the operating environment, namely humidity and lubrication, on the coating abrasiveness are directly investigated. The coating abrasiveness decreases at a slower rate when a lubricant is added and when the humidity decreases.     

Effects of a base coating used for electropolymerization of poly(3,4-ethylenedioxythiophene) on indium tin oxide electrode

Electropolymerization of poly(3,4-ethylenedioxythiophene) (PEDOT) films on indium tin oxide (ITO), using a very thin PEDOT:poly(styrene sulfonate) (PEDOT:PSS) film as a base coating, was carried out in a non-aqueous solution containing the monomer, an electrolyte and propylene carbonate by a two-electrode system. For comparison, PEDOT film electrodeposited on bare ITO substrate under the same condition was also presented. The PEDOT films deposited on these two substrates were characterized by scanning electron microscopy, energy disperse X-ray spectroscopy and Raman spectroscopy. The results indicate that the PEDOT film electrodeposited on bare ITO was not uniform, while the PEDOT film electrodeposited on PEDOT:PSS/ITO has better uniformity. The compositions of the different regions of PEDOT film electrodeposited on bare ITO and PEDOT:PSS/ITO were studied and discussed. Electrochromic devices (ECDs) based on PEDOT films electrodeposited on bare ITO and PEDOT:PSS/ITO were fabricated and characterized by UV-Vis-NIR spectrophotometric study. The results show that the display contrast of the ECD based on PEDOT film electrodeposited on PEDOT:PSS/ITO was improved over that on a bare ITO substrate.     

SURFACE ROUGHNESS OF SPUTTERED SILICON. II. MODEL VERIFICATION

Experimental verification of the mathematical surface roughness model for sputtered silicon was performed. The beam shape and its significant level of intensity were determined first by measuring the topography of craters sputtered by focused ion beam (FIB). Then the beam function was generated for various combinations of beam parameters. The material function was developed both by theoretical and experimental analysis. These two functions were then used in the model to calculate the theoretical surface roughness. Microsurface analysis was formed by FIB sputtering of a (100) silicon wafer. The surface roughness at the bottom of the sputtered features was then measured using an atomic force microscope. The theoretical surface roughness was found to be within ±1 and ±5 nm of the measured surface roughness with the measurement uncertainty (standard deviation) of about ±0.36 and ±0.85 nm for R_a and R_t, respectively.     

赖氨酸高产菌株的选育

赖氨酸作为一种重要的饲料用氨基酸,需求量一直在不断增长。传统的赖氯酸生产菌株都是多年来是经过多轮随机突变和筛选得到,而近年来随着基因重组技术的发展及对生物代谢过程的了解,人们已经能够通过基因重组技术,改变代谢途径,提高赖氨酸产量。目前有不少成功将野生菌株改造为高产菌株的案例,他们都可以作为合理设计代谢途径并结合各种组学进行微生物代谢途径改造的基础。本文主要描述通过代谢途径改造并结合高通量筛选技术,快速得到赖氨酸高产菌株的方法。