A critical analysis on the friction modelling in orthogonal machining

Despite the development of high performance finite element-based codes, the simulation of machining still represents a very hard task due to the geometric complexity of the real chip-tool systems and the high cutting speed that requires very long simulation times. For these reasons, many aspects related to machining are not very clear and so easy to simulate. In this paper a rigorous investigation on the role played by the implemented friction model within a 2D simulation of orthogonal cutting was carried out, taking into account different models proposed by the researchers in the last years. The main simulation results were compared with experimental measurements in order to verify if it is possible to identify the best model. Once the comparison with mechanical variables was completed, a subsequent study on temperature predictions utilizing the above friction models was executed as well. The results of this integrated numerical and experimental work are carefully reported in the paper.     

红外辐射吸收法测量火焰温度

简述了几种温度测量的方法，介绍了红外辐射吸收法测温原理及实验装置，并对稳定的煤气火焰进行温度测量，试图在此基础上测量固体推进剂火焰的温度。     

片材机头中物料温度分布的模拟分析

本文利用ANSYS和MATLAB软件,对衣架型和T型片材机头中熔体的温度分布进行三维有限元模拟和分析。通过对机头流道内温度分布的模拟,得出了衣架型机头流道的温度分布优于T型机头。     

复合型高分子自限温发热材料及元器件在汽车冷启动方面的应用

采用HDPE／CB复合型高分子自限温发热材料制备了适于在汽车上使用的自限温加热带、发热管及相应的加热器，通过实验室模拟试验，研究了加热器的电热特性。在冬季的柴油车冷启动试验表明，组合加热装置对柴油车的冷启动及正常运行非常奏效，所研制的复合型高分子自限温发热材料及元器件用于汽车领域是可行的。     

Effect of temperature and age on the relationship between dynamic and static elastic modulus of concrete

This study investigates the effects of cement type, curing temperature, and age on the relationships between dynamic and static elastic moduli or compressive strength. Based on the investigation, new relationship equations are proposed. The impact-echo method is used to measure the resonant frequency of specimens from which the dynamic elastic modulus is calculated. Types I and V cement concrete specimens with water-cement ratios of 0.40 and 0.50 are cured isothermally at 10, 23, and 50 °C and tested at 1, 3, 7, and 28 days.Cement type and age do not have a significant influence on the relationship between dynamic and static elastic moduli, but the ratio of static to dynamic elastic modulus approaches 1 as temperature increases. The initial chord elastic modulus, which is measured at low strain level, is similar to the dynamic elastic modulus. The relationship between dynamic elastic modulus and compressive strength has the same tendency as the relationship between dynamic and static elastic moduli for various cement types, temperatures, and ages.     

焦炭高温反应炉温度控制系统的改进

介绍了焦炭高温反应炉的温控工艺及程控曲线，给出了程控曲线的控制结构、主回路以及实现多套PI参数控制的方法。     

乙烯装置急冷系统的综合治理

针对北京东方化工厂乙烯装置汽油分馏塔、稀释蒸汽发生系统以及急冷水、酸性水pH值等在运行中出现的问题，说明了问题的原因所在。通过优化操作、改造等方式对系统进行了整改，阐述了整改后的效果。     

Young's modulus of cement paste at elevated temperatures

Calcium silicate hydrate is a porous hydrate that is sensitive to temperature and readily loses strength at elevated temperatures. Mechanical and chemical changes in the microstructure, due to escaping water, can significantly affect the mechanical properties, but these changes occur over different temperature ranges. By measuring Young's modulus as a function of temperature using the dynamic mechanical analyzer, the temperature range in which the greatest change in stiffness occurs can be identified. Additional mineralogy, pore size distribution, and composition analysis from high temperature X-ray diffraction, nitrogen sorption, and thermogravimetric analysis will demonstrate the changes in the microstructure. The results demonstrate that over 90% of the loss in stiffness occurs below 120 °C. Therefore, the damage is due to microcracking caused by pore water expansion and evaporation and not the change in mineralogy or composition. More damage, as indicated by greater loss in stiffness, occurs in stiffer and less permeable samples where higher stresses can develop.     

HEAT TRANSFER IN PARTIALLY MISCIBLE TERNARY SYSTEMS

In the study of mass transfer between partially miscible liquids, temperature perturbations have been found to have an important effect in the generation of interfacial activity. Micro- and macro-generated interfacial convection usually occurs in combination with one another even in fairly simple heat or mass transfer events. These combinations are responsible for the enhancement of mass transfer rates. In an effort to acquire a better understanding of the heat transfer effects in ternary liquid-liquid systems, temperature difference profiles were measured when contacting two partially miscible phases. A vertical and a rotational transfer cell were designed to contact the partially miscible phases without inducing external disturbances. Five thermocouples were immersed in the bottom liquid phase at predetermined positions below the interface. In order to understand the influence of the convection generated, the vertical cell was designed to hinder convection in one phase, while the rotational cell permits convection in both phases. The experimental results showed larger temperature differences in the rotational cell after the contact of the phases. Also, systems which were initially unsaturated presented larger heat effects than those in which the partially miscible solvents were initially saturated. Several parameters indicating the importance of heat effects in the ternary systems studied are reported.     

工艺参数对PP挤出发泡泡孔结构的影响

研究了螺杆转速、机头口模形状以及机头温度对挤出发泡聚丙烯(PP)泡孔结构的影响。结果表明：在挤出发泡过程中，一定配方、机头形状和温度下，螺杆转速存在最佳值；机头形状越有利于建立高压，制得的泡沫的泡孔越细密均匀且发泡倍率越高；机头口模温度在保证顺利挤出情况下．越低越有利于制得高发泡倍率的泡沫。