正确选用热力管网保温材料的几个问题

介绍了做好热力管网保温应具备的有关知识和数据，以及宝钢蒸汽主干管网在采用四种保温材料下的经济保温层厚度和相对的节能效益，认为目前适于宝钢公司热源温度在６００℃以下较好的保温材料有新型矿渣棉制品和泡沫石棉板。     

盐浓度对交联聚合物线团形态的影响

用核孔膜过滤法 (过滤体积对过滤时间作图 )、动态光散射法 (DLS)和扫描电镜法 (SEM )研究了交联反应前后盐 (NaCl)浓度变化对低浓度HPAM与AlCit形成的交联聚合物溶液 (LPS)中交联聚合物线团 (LPC)形态的影响。所用HPAM相对分子质量 1.1× 10 7～ 1.4× 10 7,LPS中HPAM与Al的质量比 2 0∶1,HPAM浓度 0 .1或 0 .2 g/L ,交联反应温度 40℃ ,时间 7天。实验结果表明 :①LPC的平均水力半径Rh(DLS测定值 )随交联反应时盐浓度的增大先减小后增大 ,盐浓度由 0 .5 g/L增加到 2 g/L时Rh 由 45 0nm迅速减小到 2 5 0nm ,盐浓度增加到 2 0 g/L时Rh达到最小值 16 0nm ,此后随盐浓度的继续增加Rh 有所增大 ;盐浓度 0 .5和 2 .0 g/L时Rh 的SEM测定值分别为45 0和 2 5 0nm ,与DLS结果一致。②交联反应完成后改变LPS的盐浓度 ,也可改变LPC的Rh 值 ,但改变幅度较小 ;盐浓度 0 .5 g/L时形成的LPS ,当盐浓度增加至 2 g/L时 ,Rh 值由 45 0nm减小至 35 9nm ,大于盐浓度 2 g/L时形成的LPS的Rh 值 (2 46nm) ;盐浓度 2 g/L时形成的LPS ,当盐浓度减少至 0 .5 g/L时 ,Rh 值由 2 46nm增大至32 6nm ,小于盐浓度 0 .5g/L时形成的LPS的Rh 值 (4 5 0nm)。用盐浓度改变引起LPC水化层厚度改变 ,线团收缩或舒张解释盐浓度改变时Rh 测定值的     

高速光通信系统中的色散问题及其补偿研究

当光纤通信系统单信道速度升级到40Gbit/s及以上时，色度色散（CD）和偏振模色散（PMD）已经成为严重影响系统性能的主要因素。本文主要从补偿的必要性、关键技术、主要方法和解决方案等方面分别对CD和PMD及其补偿进行了较详细的研究。     

Improving Wear Resistance of the Ni-base Thermal Spray-Welding Coating Using Rare Earths

ＩｍｐｒｏｖｉｎｇＷｅａｒＲｅｓｉｓｔａｎｃｅｏｆｔｈｅＮｉｂａｓｅＴｈｅｒｍａｌＳｐｒａｙＷｅｌｄｉｎｇＣｏａｔｉｎｇＵｓｉｎｇＲａｒｅＥａｒｔｈｓＺｈａｉＧｕａｎｇｊｉｅ（翟光杰）（ＩｎｓｔｉｔｕｔｅｏｆＰｈｙｓｉｃｓ，ＡｃａｄｅｍｉｃａＳｉ...     

Microstructure-Property Correlation in AI_4C_3 Dispersion Strengthened Al Composite

The microstructure and tensile properties of Al_4C_3 dispersion strengthened Al composite fabricatedby reaction milling technique were investigated.It is indicated that the rod-like Al_4C_3 dispersoidshaving a diameter of 0.02-0.03 μm and a length of 0.1-0.3μm are formed by reaction of C with Al,and uniformly distributed in the Al matrix.The interface between Al_4C_3 and Al is clean and theinterfacial bonding is good.The matrix consists of the subgrains which have the size of 0.3-0.4μm,and most of the Al_4C_3 dispersoids are distributed on the subgrain boundaries.The 11 vol.-%Al_4C_3/Al composite exhibits an UTS (ultimate tensile strength) of 400 MPa and anelongation-to-failure of 8.0%.     

Processing of Yttria-Alumina Coated Silicon Nitride Slips by Slip Casting

Si₃N₄powders coated with 6 wt% Y₂O₃and 4 wt% Al₂O₃were prepared by coprecipitation. The resulting powders were dispersed in water at different pH values and with addition of various amounts of ammonium polyacrylate (NH₄PA) to produce 32 vol% slips. The influence of the amount of NH₄PA solution added and pH on the rheological properties of 32 vol% coated Si₃N₄slips were studied. In addition, the sintered density of cast samples was determined and related to the degree of slip dispersion. The adsorption of the NH₄PA on the coated particle surface was rather high and the surface became saturated near 0.86 mg/m²at pH 9.2. High NH₄PA concentrations (1.7–3 wt%) were necessary to obtain well dispersed 32 vol% coated Si₃N₄slips at pH 9.2. The best stabilization was obtained with the addition of 2.3 wt% NH₄PA; in this condition, the viscosity reached a minimum value of 35 mPa.s at 100 s^–1. The slip viscosity increased with increasing pH from 9.2 to 10.2. Slips with low viscosities gave a more dense packing of cast samples and consequently higher sintered density values.     

SiGe／Si多量子阱中垂直方向红外吸收及共振色散效应

用垂直入射的中红外光束调制非掺杂SiGe/Si量子阱中光致子带间吸收，氩离子激光器作为子带间跃迁的光泵浦源在阱中产生载流子，红外调制光谱用步进式傅立叶变换光谱仪记录，实验中观察到明显的层间干涉效应与子带间跃迁有关的色散效应，理论和实验分析认为样品折射率变化造成的位相调制可以补偿吸收所造成的幅度调制。     

瞬态瑞雷面波法在软岩地层勘探中的应用

结合工程实例，介绍了在物性条件和地质条件复杂地区利用面波勘探技术解决软岩地区第四系覆盖层及其岩埋深的勘探方法。     

功率电子器件用AlN陶瓷基板的研制

阐述了AlN陶瓷的烧结原理 ,分析了烧结工艺参数对大面积AlN基板性能的影响 ,成功研制出了高热导率(190W /m·K)、大面积 (14 0mm× 90mm)、翘曲度为 2 0 μm/5 0mm的AlN陶瓷基板。     

The Clausius inequality corrected for heat transfer involving radiation

The objective of this paper is to prove that the Clausius inequality must be re-stated to have general applicability for heat transfer involving radiative fluxes. The integrand (đQ/T) of the Clausius expression applies to heat conduction and convection, but does not hold for most radiative transfer scenarios, with the exception of reversible infinitesimal net blackbody radiation transfer. In other cases involving radiative transfer, the equality holds for a cycle even though irreversible heat addition by radiative transfer occurs. This is without the erroneous presumption of entropy destruction anywhere in the cycle. Thus, the Clausius inequality indicates reversibility for a cycle that includes an irreversible process. Further, in some radiative cases the quantity đQ/T, where T is the boundary temperature, is not the entropy transfer at the system boundary, and in fact, primarily represents entropy production within the system. It is also clear that in another case considered, the quantity đQ/T had no physical meaning whatsoever. Consequently, the Clausius expression has been re-stated so that it is applicable to cycles with processes involving any form of heat transfer. A new integrand (đQ_cc/T + đS_Net,Rad) is presented, allowing the Clausius inequality to generally apply to all heat transfer scenarios. The work in this paper emphasizes the need to re-state other fundamental equations allowing applicability to all heat transfer processes, and draws attention to the unique character of radiative entropy calculations.