高分2号图像业务化大气校正查找表的设计与实现

为实现高分2号图像(GF2)业务化大气校正,利用矢量6S模型(6SV)将辐射传输散射与吸收进行分离计算,其中散射部分采用涵盖各种大气模式、气溶胶类型、成像几何等条件下的大气校正查找表(look-up tables,LUTs)表示,大气吸收部分采用6SV拟合计算的6种大气模式下大气透过率的经验公式表示,这种处理有效简化了查找表大小.在内存4 GB、主频3.10 GHz条件下,通过比较基于本查找表方法和基于FLAASH大气校正软件对北京地区一景GF2数据处理.结果表明:以6SV模型直接大气校正法结果作为真值,两者的绝对误差分别为0.8%和2.6%,处理时间分别为77 s和240 s,该大气校正查找表在处理精度和效率更加适合业务化大气校正.     

铸造铝合金轮毂T6热处理工艺的优化研究

研究了固溶时间、淬火停留时间及涂装烘烤工艺对A356合金铸造轮毂性能的影响规律并优化了T6热处理工艺，将淬火停留时间缩短到2h。研究表明：未涂装时优化工艺使合金抗拉强度达到240MPa，屈服强度达到181MPa。伸长率达到8％；涂装后抗拉强度达到262MPa，屈服强度达到179MPa，伸长率达到9％，接近并达到目前国内T6工艺的强度性能，超过了国内轮毂行业的强度性能标准，具有一定的生产实际意义。     

Infrared heat treatment of Ti-6Al-4V with electroplated Cu

The objective of this study is to investigate an innovative infrared (IR) technique to enhance adhesion of electroplated copper (Cu) on Ti-6Al-4V without dichromate dipping. The ultimate goal is to develop a Cu coating process on Ti-6Al-4V without hazardous hexavalent chromium (Cr) solution treatments. Cu coatings of around 50 μm were electroplated on Ti-6Al-4V specimens at a current density of 0.03 A/cm² in an acidic Cu solution. To improve adhesion of coatings, IR heat treatments were performed on the Cu-coated samples at different temperatures and durations: 860 °C for 600 s and 875 °C for 20–120 s. This process was accomplished in an attempt to replace the use of dichromate dipping before electroplating. For samples heat treated at 860 °C, no bonding existed, even after 600 s. It is believed that solid-state diffusion prevailed at 860 °C and that 600 s was not enough for sufficient diffusion to occur. Adhesion was poor when samples were heat treated at 875 °C for 20 s. Excellent adhesion was observed when the heat treatment holding time was increased to 40 s. For 90 s, the surface appearance of coatings partially changed from Cu-colored to a grayish color. There was no Cu left on the surface after a 120 s heat treatment. From optical microscopic observations on sample cross sections, an interlayer between the Cu and Ti-6Al-4V formed when heat treated at 875 °C for 40 s and longer. The interlayer thickness increased as the holding time increased, until depletion of Cu. The sheet resistivity of coated specimens was on the order of pure Cu for samples heat treated at 875 °C and less than 90 s. During the 875 °C heat treatment, the following occurred: solid-state diffusion of Cu in Ti-6Al-4V, formation of eutectic solutions, dissolution of Cu and Ti-6Al-4V into the liquid phase, and the formation of intermetallic compounds. The lowest eutectic temperature of 875 °C played a key role in this innovative process of Cu coating on Ti-6Al-4V. This paper was presented at the 2nd International Surface Engineering Congress sponsored by ASM International, on September 15–17, 2003, in Indianapolis, Indiana and appears on pp. 403–10 of the Proceedings.     

Oxidation behavior of 2.25Cr-1Mo steel with prior tempering at different temperatures

The oxidation behavior of a normalized 2.25Cr-1Mo steel tempered previously for 10 hr at different temperatures between 873 and 1023 K has been studied up to a maximum duration of 1000 hr in air at 773–973 K. The oxidation resistance of the steel was found to decrease significantly with the temperature of tempering. Tempering of this steel is reported to cause microstructural changes involving precipitation of Cr as carbides and a decrease in the effective (free) Cr contents, that could influence the oxidation resistance of the Cr-containing alloys. Relative compositions across the thickness of the oxide scales, as analyzed by SEM/EDX and SIMS, suggest that a less Cr-rich (and less protective) and thicker scale on the steel formed because previous tempering caused extensive depletion of free Cr.     

Effect of binder-phase modification and Cr3C2 addition on properties of WC-IOC0 cemented carbide

For production of fine-grained and corrosion-resistant tungsten carbide (WC) based cemented carbides, addition of chromium carbide (Cr₃3C₂) in small amounts is standard practice. No systematic study, however, has been made of the effects of large additions (maximum 6 wt % ) of Cr₃C₂ as a substitute for tungsten carbide. This study focuses on the effect of hard-phase substitution by C₃C₂ in WC-1OCo cemented carbide. An attempt is also made to modify the binder metal cobalt by partial or complete substitution of nickel. Specimens were prepared using the standard liquid-phase sintering process and were tested for sintered porosity, mechanical properties, corrosion resistance, and microstructural parameters. Results confirm the findings of earlier workers regarding grain refinement and improvement of mechanical properties upon the addition of small amounts (<2 wt%) of Cr₃C₂. Modification of the binder phase improves indentation fracture toughness and corrosion resistance. Addition of Cr₃C₂ independent of the binder type improves corrosion resistance.     

ZTC4筒形件温成形扩口数值模拟

对铸造Ti-6Al-4V筒形件温成形扩口成形工艺进行了数值模拟分析,得出了优化的工艺参数,并对凸模锥角进行了优化模拟,得出了合适的锥角。     

Stabilization of One‐Dimensional Schrödinger Equation with Variable Coefficient under Delayed Boundary Output Feedback

This article considers stabilization of a one‐dimensional Schrödinger equation with variable coefficient and boundary observation which suffers from an arbitrary given time delay. We design an observer and predictor to stabilize the system. The state is estimated in the time span where the observation is available, and also predicted in the time interval where the observation is not available. It is shown that the estimated state feedback stabilizes the system exponentially. A numerical simulation is presented to illustrate the effect of the stabilizing controller.     

利用SQLServer实现局域网软件自动升级

介绍了一种只利用SQLServer,无需其他专门服务器就可以轻松实现的局域网软件自动升级方法。