环氧树脂-聚丙烯酸酯乳液型复合薄膜粘合剂

本文主要叙述了环氧-丙烯酸酯聚合乳液的合成,以及该乳液粘合剂的配制;讨论了该乳液粘合剂的粘合性能及耐水、耐溶剂性能。     

新型可见光固化口腔正畸粘合剂研制

介绍了一种新型可见光固化正畸粘合剂的组成、性能及正畸粘接的工艺。此粘合剂由一种单组分液体底胶和单组分糊剂组成。与化学固化粘合剂相比,其操作使用方便,固化时间短。这种新型粘合剂的粘接强度完全满足了正畸粘合剂的要求。     

CaSO_4晶须对聚氨酯胶粘剂性能影响的研究

用实验室自制的相对分子质量为2500的聚己二酸-1,4-丁二醇酯二醇和甲苯二异氰酸酯、混合扩链剂配制聚氨酯胶粘剂,并使用实验室自制的改性和未改性200nm硫酸钙晶须对聚氨酯胶粘剂进行改性,考察不同硫酸钙晶须及其加入量、加入方式对聚氨酯胶粘剂综合力学性能的影响。根据实验结果,200nm改性硫酸钙晶须当加入量为3％时,聚氨酯胶粘剂的拉伸强度、初粘性和最终剥离强度均有明显提高。     

An Experimental Study of Fatigue Strength for Adhesively Bonded Tubular Single Lap Joints

In this paper, manufacturing technology of the tubular single lap adhesive joint was studied to obtain reliable and optimal joint quality. In addition, a surface preparation method and a bonding process for the joint were devised. The effect of the adhesive thickness and the adherend roughness on the fatigue strength of the joint was experimentally investigated. From experiments, it has been found that the fatigue strength of the joint increased as the adhesive thickness decreased and the optimal arithmetic surface roughness of the adherends was about 2 μm.     

用于光纤并带的UV固化胶粘剂性能的研究

研究了用于光纤带的紫外光固化胶粘剂的剥离性、柔韧性、拉伸强度和延伸率的影响因素。     

HT-730改性酚醛-丁腈胶粘剂的研制

对酚醛-丁腈胶粘剂进行改性，添加5．0％的硅烷偶联剂，改善了酚醛-丁腈胶粘剂的工艺性能，提高了粘接强度，特别是降低了酚醛-丁腈胶对环境湿度的敏感性。研制的HT-730胶在环境湿度90％时仍有很高的粘接强度，同时老化性能和适用期并没有受到影响。     

汽车工业生产用热熔胶膜的研制

介绍了汽车工业生产内装饰复合材料用热熔胶膜的性能及其研制状况。这种热熔胶膜具有使用便捷,高效,生产、使用过程中没有污染的具有热熔胶膜的特长。     

汽车灯用热熔胶的研究及性能表征

介绍了生产汽车灯用热熔胶的各种原料及其在胶粘剂中所起的主要作用，为汽车灯用热熔胶原料的选择提供了参考。还介绍了汽车灯用热熔胶的制备过程和厂家所需的各种性能及其表征方法。通过选择适当的原料及配比，生产出性能优良并具有良好市场前景的产品。     

胶层厚度对拉伸试样应力分布影响的数值分析

运用弹塑性有限元法研究了胶层厚度对承受拉伸载荷的对接接头胶层内应力分布的影响．三维有限元法数值分析的结果表明，随胶层厚度减小，胶层中正应力SZ与剪应力SYZ的分布趋于均匀；而对正应力SY而言，胶层厚度为0．15mm时，其边缘峰值应力最低。     

Bulk and Interphase Effects in Aged Structural Joints

Although structural adhesives are becoming widespread in numerous applications, one important limitation at present is the long term behaviour of bonded assemblies under conditions of high humidity, especially at elevated temperatures. This study presents a comparison between bulk properties of a structural epoxy resin and its behaviour in a torsional joint consisting of a hollowed-out cylinder bonded to a plate—both substrates being in stainless steel. Exposure to ca. 100% relative humidity at 70°C leads to modification of the bulk properties of the polymer, notably reduction of its elastic modulus. Although this may explain some differences in behaviour of the torsional joint, premature failure is attributed to weaknesses in the interphase zone.

Auger Electron Spectroscopy (AES) has been employed to investigate both unbonded steel surfaces and fracture zones. Although prolonged exposure to water leads to a more extensive degree of (apparently) adhesive failure at the interface polymer/metal, AES has shown the presence of non-negligible quantities of carbon, attributed to residual polymer. Failure would seem to occur, at least partly, in a weak interphase of the polymer, near, but not at, the interface.

Various possible causes are evoked. For dry failure, residual polymer may be due to the topography of the metal surface and/or local modification of the adhesive during cure. In the case of aged joints, in addition there are potential effects due to swelling and differential stresses, secondary bond failure and molecular chain scission within the polymer, all provoked by the presence of water.