制造任务分解与制造单元级资源配置协同优化

针对网络化制造环境下制造任务分解与资源配置脱节的问题,提出了制造任务逐层分解与制造单元级资源配置协同优化的方法,建立了协同优化流程.在对制造任务特点进行分析的基础上,建立了制造任务模型和制造单元资源模型,建立了多目标优化模型和目标的综合评价体系,利用在遗传算法求解搜索过程中所获得的动态信息进行综合评价,并随着求解搜索过程的深入对变异幅度进行调整,以达到全局优化和加快收敛速度的目的.最后以实例验证了该方法的可行性与有效性.     

米曲霉在牛乳中最适生长条件的研究

利用米曲霉对牛乳进行发酵,通过单因子及正交试验以菌丝体干重为指标对其在牛乳中的生长进行了研究．结果表明：接种量为4％,装液量为30mL,摇床转速为180r／min时菌丝体干重可达到最大．此外测得最大菌丝体干重时的蛋白质分解率可达35．6％．     

Pressureless low temperature sintering of nanocrystalline zirconia ceramics via dry powder processing

Pressureless sintering approaches provide a simple avenue to manufacture dense ceramic parts with minimal processing equipment, but current pressureless sintering techniques have yet to demonstrate capabilities of producing dense ceramics while maintaining sub-50 nm grain sizes. Nanocrystalline yttria stablized zirconia ceramics were process from 4 mol% yttria stablized zirconia (4YSZ) nanopowders with a crystallite size of 7.5 nm using dry cold isostatic pressing (CIP) where powders are dried immediately prior to green compact formation and CIP vacuum bagging. It is shown that CIP pressures >75 000 psi (517 MPa) effectively remove pores larger than 100 nm and that pressureless sintering occurs at reduced temperatures for green densities ≥50%. Though the sintering kinetics are shown to be similar to other zirconia nanopowder sintering studies, the small initial crystallize size and reduced sintering temperature allowed densities as high as 97.2%, while retaining a ceramic grain size at or below 40 nm. Produced nanocrystalline 4YSZ ceramics with a grain size of 30.3 nm and a density of 96.3% had Vicker's hardnesses as high as 14.2 GPa and Vicker's indentation fracture resistance of 3.43 MPa·, demonstrating that simple processing approaches can be refined to fabricate nanocrystalline ceramics while maintaining high hardness and indentation fracture resistance.     

Studies regarding simulation process to static loading of the structures obtained from polylactic acid, 3D printed

Being a relatively new process, additive manufacturing needs many studies to be able to produce parts with the required properties. The aim of the paper is to establish whether, based on the physical and mechanical properties determined by tensile testing and by applying finite element analysis (FEA), viable results can be obtained regarding the behavior of the 3D printed structures at the different, static loading. The application of FEA for the tensile testing of 3D specimens led to the results close to those obtained by the tests. The values of the results obtained by simulation are higher by up to 7.2% compared with those recorded by tests. The simulation was applied both for the printed specimens from a single material and from two materials (multi-material). Regardless of the materials used in printing and the simulation method, the results of applying FEA are close to those recorded by testing.     

IMPROVEMENT ON FATIGUE LIFE OF ALLOY LY12CZ AFTER LASER RADIATION AND ITS DAMAGE EVOLUTION

The change of microstructure of fatigue specimens before and after laser radiation was studiedby transmission electron microscopy.The results show that the diameter of dislocation cell λtends to a constant at fatigue failure.Based on the principles of continuous damagemechanics,expressions of the fatigue damage criterion and processes of fatigue damage evolu-tion for L Y12CZ have been derived.     

Corrosion resistance of austenitic stainless steel separator for molten carbonate fuel cell

STS310S and SC-STS310S (simultaneously co-deposited chromium and aluminum onto 310S austenitic stainless steel substrate by pack-cementation process) were used as separator materials on the cathode side of a molten carbonate fuel cell. With the STS310S, corrosion proceeded via three steps; a formation step of unstable corrosion product, a protection step against corrosion until breakaway, and an advance step of corrosion after breakaway. The final corrosion product was LiFeO₂ and the loss of mass was 6.5 mg/cm² after a corrosion test of 480 hr at 650°C. The SC-STS310S showed more effective corrosion resistance, however, than did common STS310S. There was especially no corrosion loss on the SC-STS310S after the 480 hr corrosion test. It is anticipated that it will be very useful as an alternative separator on the cathode side off the MCFC in the future.     

面向21世纪的信息化制造

本文叙述了信息化制造的哲理 ,分析了其特点 ,提出了其体系结构及企业新产品开发模式和企业电子商务 ,并分析了信息化制造的关键技术。     

Optical complexities of living cytoplasm--implications for live cell imaging and photo-micromanipulation techniques

The ability to manipulate the intracellular environment within living cells and to monitor the cytosolic chemical changes which occur during cell stimulation has lead to major advances in our understanding of how cells read and respond to their environment. Perhaps the most powerful suite of techniques for achieving these dual objectives is based on the use of light (photons). Because cells are 'transparent', light has been used to both interrogate and manipulate the chemistry inside living cells, exploiting technical advances in both the physical and biochemical sciences. However, cells are neither transparent nor homogeneous with respect to their optical properties. The interface between light and the living cell cytoplasm thus represent an important, yet largely ignored, interface. There has been no review of the optical properties of cytoplasm and little discussion about how the optical properties of living cytoplasm influence the outcome of such measurements and manipulations. In this short review, we discuss the importance of understanding the optical properties of cytoplasm for such techniques and how imperfections in experimental interpretation can arise.     

战略网络形成动因之制造模式篇

本研究目的在于探究战略网络生成中制造模式的推动作用。文章首先分析了制造模式在技术经济范式变迁中扮演的角色,总结出制造模式与技术经济范式之间的关系,接着运用数学抽象和哲学思辨的方法,提炼出人类历史上三次制造模式对技术经济范式的价值实现函数。基于该函数研究发现:精益生产中目的在于充分调动人的主观能动性,以实现人的解放的复合机制——现场管理、劳工关系管理和知识管理等体系是制造模式未来的发展方向;战略网络的演进服务于制造模式的价值实现功能,它的生成是为了弥补制造模式柔性不足的缺陷。     

A methodology to incorporate product mix variations in cellular manufacturing

The identification of part families and machine groups that form the cells is a major step in the development of a cellular manufacturing system and, consequently, a large number of concepts, theories and algorithms have been proposed. One common assumption for most of these cell formation algorithms is that the product mix remains stable over a period of time. In today’s world, the market demand is being shaped by consumers resulting in a highly volatile market. This has given rise to a new class of products characterized by low volume and high variety. To incorporate product mix changes into an existing cellular manufacturing system many important issues have to be tackled. In this paper, a methodology to incorporate new parts and machines into an existing cellular manufacturing system has been presented. The objective is to fit the new parts and machines into an existing cellular manufacturing system thereby increasing machine utilization and reducing investment in new equipment.