固液相变蓄能的数学模型和自然对流换热系数的实验研究

引入自然对流换热系数 ,将固液蓄能数学模型简化为仅用能量方程加以描述。并通过实验测得相变过程的实际温度场 ,证明了自然对流固液相变换热的影响不可忽略 ,验证了固液相变界面移动速率随自然对流换热系数的增大而增大的定性关系     

板式换热器热端跑冷问题的分析及处理

１００００ｍ３／ｈ制氧机板式换热器损坏修复后，热端跑冷严重，氧气取出量不足，制氧机工况恶化，通过分析找出了原因是因某单元氧通道堵塞，并采取了处理措施。     

Open‐cycle OTEC systems with freshwater product: Effects of noncondensable gases on performance of condenser

An open‐cycle ocean thermal energy conversion (OC‐OTEC) system is one of the energy conversion methods used to generate electricity from ocean thermal energy. For the OC‐OTEC system, steam evaporated from the surface seawater due to flash evaporation drives the turbine. At that time, dissolved gas such as air is introduced into the low‐pressure system (OC‐OTEC system) as the noncondensable gas, which degrades the performance of condensation heat transfer. In this paper, a small‐scale OC‐OTEC experimental unit experimentally investigates the effect of noncondensable gas on the heat transfer performance in a condenser. The experimental results are discussed in comparison with theoretical estimation by the Sparrow–in method. It is shown that the condensation is occupied by heat and mass transfer near a condensation surface and that the condensation efficiency is affected by exhaust quantity of noncondensable gas at a relatively high concentration ratio of condensable gas. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 154(1): 29–35, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20179     

Analysis and Optimization Laminar Viscous Flow Through a Channel

Optimizing of laminar viscous flow through a pipe by two dimensionless values is investigated analytically. Dimensionless entropy generation and pumping power to heat transfer rate ratio are used as basis for constant viscous and the temperature dependence on the viscosity. For this matter we calculate entropy generation and pumping power for a fully developed in a pipe subjected to constant wall temperature for either constant viscosity and the variable viscosity. The variation entropy generation increase along the pipe length for viscous fluid is drawn, either the variation summation dimensionless entropy generation and the pumping power to heat transfer rate ratio are varying the fluid inlet temperature for fixed pipe length and are varying pipe length for fixed fluid inlet temperature are drawn. For low heat transfer conditions the entropy generation due to viscosity friction becomes dominant and the dependence of viscosity with the temperature becomes essentially important to be considered.     

一种蒸发式冷凝器的新型设计方法

蒸发式冷凝器设计方法的粗糙和繁琐限制其广泛应用,特别是限制其应用于民用和小型商用建筑中。针对上述问题,作者通过实验研究了蒸发式冷凝器的影响因素（进风湿球温度、最小截面风速和喷淋水量）对蒸发式冷凝器热质交换的影响。同时提出了一种新型设计方法,此方法简单,精度较高。适合工程设计、选型和生产应用。     

空分设备的酸性腐蚀及预防

以切换式换热器空分设备为例 ,分析了空分设备酸性腐蚀的原因、可能造成的危害 ,提出了预防措施。     

Discrete Modeling and Suggested Measurement of Heat Transfer in Gas-Solids Flows

This article presents a two-dimensional transient model for gas-solids flow and heat transfer through pipes using the coupled Computational Fluid Dynamics and Discrete Element Method approach. Numerical simulations have been conducted to examine the modification of fluid thermal structure due to the presence of particles in a pneumatic transport pipeline. Modeled results have demonstrated the key role of transversal motion of rebounding particles in the pipe cross section in altering fluid temperature. Further implementation of this modeling technique in air-drying processes is discussed and possible experimental methods for the measurement of in situ particle and fluid motion and temperature profile are cited.     

A numerical model for induction heating processes coupling electromagnetism and thermomechanics

This paper presents a mathematical and numerical model developed for coupling the various physical phenomena (electromagnetic, thermal and mechanical) taking place in axisymmetrical induction heating processes. All three electromagnetic, thermal and mechanical models are time dependent and take full account of the electromagnetic and thermal non‐linear effect especially with magnetic materials. The electromagnetic problem is discretized and solved in the workpiece, air and inductors. The heat transfer equation and the mechanical equilibrium equations are solved in the workpiece only, both using a finite element method. The mechanical model can take into account thermoelastic–plastic behaviour for the part. The model has been successfully applied to several cases of induction heating. Comparisons between numerical and experimental results show an excellent agreement. Copyright © 2003 John Wiley & Sons, Ltd.     

Immobilized α-amylase from Bacillus licheniformis: a potential enzymic time—temperature integrator for thermal processing

Biphasic and nth-order models were tested as to their usefulness to fit experimental inactivation data of Bacillus licheniformis α-amylase, immobilized on glass beads, and were discussed with respect to their suitability to characterize the considered enzymic system as a time—temperature integrator (TTI) to evaluate heat processes. Both isothermal and non-isothermal inactivation experiments were carried out. Model (kinetic) parameters (rate constant k, activation energy E_A and reaction order n) were estimated using a non-linear regression procedure. The results obtained, especially the activation energy of about 293 kJ mole^–1, indicated a potential use of this system as a TTI for heating processes in the temperature range of 96–108°C.