Rolling texture and its effect on tensile property of a near-α titanium alloy Ti60 plate

Rolling texture and its effect on tensile properties of Ti60 alloy plates were investigated in the present study. The plates wereβ-rolled at 1070℃ and(α+β)-rolled at 980℃, using uni-directionally rolling(UDR) and cross-directionally rolling(CDR) processes, respectively.β-rolled plates exhibited weak textures, which were attributed to the dispersive orientations of secondary α during the β→α phase transformation. Strong deformation textures formed in(α+β)-rolled plates as a result of slipping mechanisms: the strong T-type texture in UDR plate was related to {10 1 0}[11 2 0] slipping, while the B-type texture in CDR plate was relevant with {0001}[11 2 0] slip. Strong T-type textures led to anisotropic tensile properties. B-type textures would decrease such an anisotropy. The(α+β)-CDR process was found to be a candidate process for reducing anisotropy of Ti60 alloy plates.     

基于多目视觉的变形钢板三维测量方法

提出了一种使用4个相机测量变形钢板三维形状的方法;在没有纹理的钢板上画一些点,使用4个相机同时拍摄钢板;利用边缘检测算法找出钢板的边缘,利用特征点提取算法提取出4个图像中钢板上的特征点,并找到4个图像上精确的特征点匹配关系,然后测量出这些特征点的三维点;最后,以这些三维点为种子点向外区域增长,从而得到钢板的三维形状;实验对变形钢板进行三维测量,得到了钢板的精确的三维形状,结果验证了该方法的有效性和可行性。     

The thin plate spline robust point matching (TPS-RPM) algorithm: A revisit

This paper reviews the TPS-RPM algorithm (Chui and Rangarajan, 2003) for robustly registering two sets of points and demonstrates from a theoretical point of view its inherent limited performance when outliers are present in both point sets simultaneously. A double-sided outlier handling approach is proposed to overcome this limitation with a rigorous mathematical proof as the underlying theoretical support. This double-sided outlier handling approach is proved to be equivalent to the original formulation of the point matching problem. For a practical application, we also extend the TPS-RPM algorithms to non-rigid image registration by registering two sets of sparse features extracted from images. The intensity information of the extracted features are incorporated into feature matching in order to reduce the impact from outliers. Our experiments demonstrate the double-sided outlier handling approach and the efficiency of intensity information in assisting outlier detection.     

烧结与冷镦过程中铝硅共晶合金显微结构与密度的演变

采用烧结及后续的镦粗工艺制备了铝硅共晶合金块体材料,研究了烧结温度对烧结体显微结构、抗压强度及相对密度的影响。结果表明：烧结温度显著影响烧结体的显微结构和抗压强度,以临近铝硅共晶合金液相线的温度烧结时,发生了局部熔化,产生的熔融液体破坏了颗粒表面的氧化膜,颗粒之间相互黏结,形成了烧结骨架。以优化的555℃烧结,Si颗粒呈球状,抗压强度达到最佳,但相对密度未发生变化。在后续的冷镦过程中,烧结骨架及粉末颗粒均产生变形,孔隙减小,颗粒呈扁平状,相对密度达到了98%。     

造粒机模板与切粒刀对聚乙烯颗粒质量的影响

通过多年来对聚乙烯造粒系统的调查研究及现场实践，确认了聚乙烯产品质量的影响因素。选择了造粒模板与切粒刀之间的最佳匹配。     

储氢与合金材料

介绍了储氢合金材料和开发应用动态。     

Room temperature oxidation of lead-indium alloy films

The kinetics of growth of thin (14 to 40Å) oxide layers on lead-indium alloys was investigated ellipsometrically, using: 3000Å thick films at 23°C; and oxygen exposures at 760 torr for times ranging from five minutes to five days. Assuming that the oxide layer is comprised of a two-phase mixture of PbO and In₂O₃ having a negligible extinction coefficient made it possible to estimate the oxide composition from the ellipsometrically-obtained oxide refractive index. Under these oxidizing conditions, the volume fraction of PbO in the oxide mixture decreases from a value of unity for pure lead to zero for alloys containing more than 30 at. percent In, in agreement with the Auger Electron Spectroscopy results of Chou and coworkers. The oxidation rate equals a exp (X₁/X), where α and X₁ will be seen to vary complexly with alloy composition. A theoretical explanation of these results is also presented.     

多元回归分析在电热式平板硫化机热板温度场中的应用

分析电热平板硫化机热板温差大的主要影响因素,重点研究热源分布情况对温差的影响.以400×400电热平板硫化机为例,应用多元回归的二次响应曲面模型及其子模型,对热源间距(电热管间距)与热板表面最大温差之间的函数关系进行预测,检验并分析预测结果(拟合曲线)的可靠程度,从而得出较合理的数学模型,即完整二次响应曲面模型.此模型可为工程设计提供参考依据.