Characterization of resol resins modified by the addition of PVC plastisols

Plastisols, which are a blend of poly(vinyl chloride) resin and a plasticizer (DEHP), were used as a toughening agent of a resol resin in order to improve the mechanical properties. It was not possible to formulate resol blends by adding more than 10 % of plastisol owing to a lack of apparent homogeneity in the systems, which also showed many air bubbles. The relationship between dynamic mechanical, mechanical and thermal properties and the amount of plastisol added was studied. It was determined from the infrared spectroscopy and dynamic mechanical results that the resol–plastisol blends seem to be formed by a reaction between the phenol and PVC giving a higher crosslinked structure. An improvement in the thermal resistance of the blends at lower temperatures was observed with an increase in the percentage of plastisol. Flexural analysis showed the elastic behaviour of the systems. However, it was not possible to observe the effect of the plasticizer (DEHP) owing to the low quantity of plastisol that was added to the resol. Copyright © 2004 Society of Chemical Industry     

Pultruded fibre reinforced polyurethane composites II. Effect of processing parameters on mechanical and thermal properties

This paper presents a novel process for the fabrication of pultruded polyurethane (PU) composites. The effects of the processing parameters on the mechanical properties (flexural strength and flexural modulus, etc.) and thermal properties (HDT) of the fibre reinforced PU composites by pultrusion have been studied. The processing parameters investigated include pulling rate (in-line speed), die temperature, filler type and content, and post-cure time and temperature. Results show that the composites possessed various optimum pulling rates at different die temperatures. On the basis of the DSC diagram, the swelling ratio, the mechanical properties and the thermal properties of composites, the optimum die temperature can be determined. It is found that the mechanical and thermal properties increase with filler content for various types of filler. The mechanical and thermal properties increase at a suitable post-cure temperature and time. Furthermore, the properties which decreased due to the degradation of composite materials for a long post-cure time will be discussed.     

浸胶工艺对Nomex蜂窝性能的影响

本文研究了浸胶工艺对Ｎｏｍｅｘ蜂窝性能的影响，分析探讨了提高Ｎｏｍｅｘ蜂窝性能及外观质量的途径。研究结果表明：采取新的浸胶工艺制作的Ｎｏｍｅｘ蜂窝，各项性能全面达到法国宇航材料标准。     

As,Sb,Sn对30CrMnSiA钢力学性能的影响

在３０ＣｒＭｎＳｉＡ钢中加入不同量的Ａｓ，Ｓｂ，Ｓｎ元素，研究了这些元素单独存在及复合存在时对钢的强度，塑性，冲击韧度及韧脆转变温度的影响规律，并用扫描电镜及俄歇能谱分析了Ａｓ，Ｓｂ，Ｓｎ导致晶界脆化的机理。     

CHARAC TERIZATION OF TiAl POWDER PRODUCED BY MECHANICAL ALLOYING

The microstructure,alloying reaction and sintering behavior of the powder produced by Mechanical Al-loying(MA)for 8 h from 64 wt.-% Ti powder and 36 wt.-% Al powder were studied by scanning electronmicroscopy,optical microscopy,X-ray diffractometry,differential scanning calorimetry(DSC)and dilatometry.The mechanically alloyed powder partictes are Ti-Al composite particles.Thus,titanium aluminides can formeasily in the powder through diffusion during heat treatment.It is shown that the sintering behavior of this pow-der,different from the behaviors of TiAl alloy powder and mixed powder of 64 wt.-% Ti powder and 36 wt.-%Al powder,changes from expansion at temperatures below 1000℃ to shrinkage at temperatures above 1000℃.Homogeneously alloyed TiAl material with a density over 96% of the theoretical density can be produced fromthe mechanically alloyed powder by compaction-sintering.     

Antimicrobial protection of cotton and cotton/polyester fabrics by radiation and thermal treatments. I. Effect of ZnO formulation on the mechanical and dyeing properties

Cotton and cotton/polyester fabrics were treated against microbial attack by applying a formulation based essentially on ZnO under high‐energy radiation and thermal curing. To achieve the homogeneity and the reactivity of the treating formulation, a binder (Impron MTP) and a dispersing agent (Setamol WS) were used with ZnO. The antimicrobial property of the fabrics was evaluated, in terms of mechanical properties, by a soil burial test. Moreover, the effect of antimicrobial finishing on the dyeing properties in terms of color strength was investigated. It was found that the best composition that affords the best antimicrobial protection to cotton fabrics contains 2% ZnO, 2% binder, and 1% dispersing agents. For the cotton/polyester blend, the best results were achieved at the same conditions except the ZnO was 1%. It was found that the treatment under the effect of electron‐beam irradiation is better than that of gamma irradiation and thermal curing. The results showed that when the finishing process was carried out before dyeing with a reactive dye, it affects the color strength rather than performing the finishing after the dyeing process. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1129–1137, 2003     

Modeling the large‐strain constitutive behavior of polycarbonate under isothermal and anisothermal conditions

The tensile behavior of polycarbonate was studied at large strains below the glass‐transition temperature. Experiments were carried out at a series of constant temperatures and also under conditions of falling temperatures. The specimens necked with a natural draw ratio of approximately 2, and the study was mainly focused on the necked material. Isothermal experiments revealed an elastic mechanism that initiated beyond the natural draw ratio. A model consisting of an Eyring process and two Gaussian elastic mechanisms was found to be applicable to both the isothermal and anisothermal stress‐relaxation and stress–strain results. The same model also produced reasonable estimates of the stresses generated during the necking process. In addition, a simple relationship between the isothermal and anisothermal stress relaxation was demonstrated. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 2105–2116, 2005     

Preparation,morphology, and mechanical properties of elastomers based on α,ω‐dihydroxy‐polydimethylsiloxane/polystyrene blends

α,ω‐Dihydroxy‐polydimethylsiloxane/polystyrene (PDMS/PS) blends were prepared by the solution polymerization of styrene (St) in the presence of α,ω ‐dihydroxy‐polydimethylsiloxane (PDMS), using toluene as solvent and benzoyl peroxide (BPO) as initiator. The PDMS/PS blends obtained by this method are a series of stable, white gums, which were vulcanized to elastomers at room temperature with methyl‐triethoxysilicane (MTES). The use level of MTES was far more than the necessary amount used to end‐link hydroxy‐terminated chains of PDMS, with the excess being hydrolyzed to crosslinked networks, which were similar to SiO₂ and acted as filler. Investigations were carried out on the elastomeric materials by extraction measurement, swelling measurement, and scanning electron microscopy. The extraction data show that at each composition the amount of soluble fraction is less than expected and the difference between experimental and theoretical values becomes more and more significant as PS content increases. This is mainly due to the grafting of PS onto PDMS and the entanglement of PS in the interpenetrating polymer network (IPN), which consists of either directly linked PDMS chains or chains linked via PS grafts and is formed by free radical crosslinking of PDMS during the radical polymerization of St. PS grafted on PDMS is insoluble and PS entangled in the IPN is difficult to extract. Both render the soluble fraction to be less than expected. As the St content in preparing PDMS/PS blends increases, the probability of grafting PS onto PDMS also increases, which may subsequently produce a higher crosslinking level of PDMS networks that linked via PS grafts by radical crosslinking. As a result, not only the amount of insoluble PS increases but also PS entangled in the IPN is more difficult to extract. Scanning electron microscopy demonstrates that the elastomer system has a microphase‐separated structure and a certain amount of PS remains in the PDMS networks after extraction, which is in accordance with the extraction data. Moreover, the mechanical properties of the elastormeric materials have been studied in detail. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3542–3548, 2004     

北方艺术一体化运用研究--写意花鸟画与印章

在当前国画创作趋于写实甚至超写实的状态下。北方写意花鸟画从其正大气象绝能独立,给画坛带来了强劲的“东北风”和浓郁的时代气息。北方写意花鸟之作无不凌射着北方的粗犷奔流之气以及旺盛难抑的生命之气,小中见大．将人引入高处不胜寒的祟高美学境界之中。然当欣赏者或学术研究者都侧重于画作的孤枣以及独到的笔墨关系的时候,都极容易忽略印章一一篆刻艺术在其画作中所起到的无可替代的重要作用。     

PVC╱NBR╱BR三元共混弹性体的制备

采用结合丙烯腈含量为26％的NBR、分子量适中的悬浮法Ⅲ型PVC和BR共混,制得了综合性能较PVC/NBR并用胶优异的弹性体。优选的工艺条件为:PVC/NBR/BR=30/60/10(质量比);补强剂选用炭黑40份,超细碳酸钙50份,轻质碳酸钙20份;硫化体系选用过氧化物加少量硫磺;混炼温度为140—170℃,混炼时间为10—15min。通过电子显微镜和动态力学分析,弹性体存在两个T,PVC为分散相,橡胶为连续相。