H原子对固态合金化颗粒表面成份分布影响的研究

本文研究了氢化物ＴｉＨ２对Ｆｅ＋Ｔｉ机械合金化非晶储氢合金的表面成份偏聚和性能的影响。应用Ｘ射线光电子谱（ＸＰＳ）和俄歇电子谱（ＡＥＳ）对样品表面由表及里逐层测量成份分布。同时应用热重分析方法研究了样品氧化性能和产物。研究结果表明，在机械合金化过程中，Ｈ原子不仅能使ＦｅＴｉ非晶化，同时促使表面产生明显的Ｆｅ原子偏聚。表面Ｆｅ／Ｔｉ原子比接近７。非晶ＦｅＴｉ（Ｈ）相的氧化分两个阶段进行，Ｔｉ原子首先氧化（８３３Ｋ），随后Ｆｅ原子氧化（８９０Ｋ）。     

链烷烃的表面张力与内压

对Ｄａｖｉｓ和Ｒｏｓｓｅｉｎｓｋｙ提出的关系检验表明，液体的表面张力σ与Ｐ１Ｖｍ１／３之比不仅取决于温度，还与液体的种类有关，据此，建立了一个能由链烷烃的分子结构准确预测其表面张力的方法。     

聚合物复合材料填充剂的改性

在前人研究的基础之上，归纳总结了聚合物复合材料填充剂的种类，综述了对其进行表面改性的目的、条件、方法、工艺以及对改性结果的表征等。文章还分析了影响填充聚合物复合材料性能的因素，指出了今后发展的方向。     

薄Si膜对基底表面粗糙度的影响

利用ＺＹＧＯ光学干涉测量仪，散射积分测量法观测了光学元件表面均方根粗糙度．详细分析了薄Ｓｉ膜对基底均方根粗糙度的影响，由此认为薄膜并不总是复制基底表面的粗糙度，结果出现了薄膜降低表面粗糙度的现象．提出了一定厚度范围的薄Ｓｉ膜的表面粗糙度存在着一个稳定值的新设想．     

Edge detection,three-dimensional cell boundary reconstruction and volume and surface area estimation from differential interference contrast images

Three-dimensional (3-D) cell morphology is important for the understanding of cell function and can by quantified in terms of volume and surface area. Differential interference contrast (DIC, or Nomarski) imaging can enable cell edges to be clearly visualized in unstained tissue due to the slight difference in refractive index between aqueous media and cytoplasm. DIC is affected in only one direction - the direction of the optical shear. A 1-D edge detector was used in that direction with a scale length equal to that of an in-focus edge to highlight cell boundaries. By comparison with the signal from the edge detector on an out-of-focus slice, the in-focus slices could be segmented and, after noise suppression, cell outlines obtained. A voxel paradigm was used to calculate cell volume and differential geometry was used for surface area estimation. We applied this approach to obtain 3-D dimensional information by optical sectioning of motile Amoeba proteus.     

Progress in deep-UV photoresists

Higher resolution can be achieved in lithography by decreasing the wavelength of the exposure source. However, resist material and their processing are also important when we move to a shorter wavelength lithography technology. This paper reviews the recent development and challenges of deep-UV photoresists and their processing technology.     

从长贮试验看引信零件表面处理方式选择

总结了历年长贮试验情况，分析了防腐层变化的原因，指出了引信零件在选择表面处理方式时应注意的问题。     

Alkali-metal Na Adsorption and Promoted Oxidation on Si(100)2×1 Surface

The alkali-metal Na adsorption on Si(100)2×1 surface and its promoted oxidation and Si oxidegrowth have been investigated by means of thermal desorption,work function,Auger electronspectroscopy and photoemission electron spectroscopy.The experimental data showed that therewas a new state,interface electron state,near the Fermi level after the deposition of Na atoms.It wasfound that the presence of Na always caused an increase of the oxygen initial uptake whereas thepromotion of Si oxide growth was observed only at the coverage of Na greater than 0.5 ML.A newmechanism of Na-promoted Si oxide growth is suggested in this paper.     

离子注入对Cr12MoV钢表面组织结构和力学性能的影响

研究了Ｃｒ１２ＭｏＶ钢离子注入层的显微组织特征及其对表面性能的影响。结果表明，离子注入使Ｃｒ１２ＭｏＶ钢的表面硬度和耐磨性能得到显著改善，且存在着一个最佳的注入剂量，约为３×１０＾１＾７Ｎ＾＋／ｃｍ＾２左右。离了注入在Ｃｒ１２ＭｏＶ钢表面层中形成了大量细小弥散的第二相粒子，并使α－Ｆｅ晶格发生严重畸变，从而引起材料表面强化。     

基底元素表面富集与扩散阻档层

根据An－Ag系统以及An－Cu系统的扩散系数计算，提出了扩散阻挡层模型。利用这个模型对Au－Ag系统进行有关实验，得利了较好的验证。