激光导向伺服系统中满意PID调节器的LMI设计

利用带有图像处理功能的小型激光导向伺服系统,可以大大降低目标坐标测定仪操作手跟踪动态飞行目标的操作难度,从而提高激光回波率.与经典的矩阵分解方法不同,本文以线性矩阵不等式方法,研究了激光导向伺服系统的满意PID调节器设计问题.首先从约束指标的相容性出发,给出满足与给定圆形极点约束相容的输出方差的取值范围.然后,在此取值范围内,得到了求取同时满足上述两种约束的PID调节器参数的方法.靶场试验结果证明了其有效性.     

基于MATLAB语言的自动控制原理多媒体教学研究

结合我校自动化专业教学，从培养高素质，复合型人才的角度，在教学中引入目前世界上流行的MATLAB软件，并把MATLAB语言应用于经典控制系统设计和分析中，在自动控制原理多媒体辅助教学方面做了一些有益尝试和探索，取得了满意的教学效果。     

广州抽水蓄能电站厂区消防设计述评

广州抽水蓄能电站是我国第一座高水头，大容量的抽水蓄能电站，该电站按无人值班设计，为此对火灾探测和消防报警以在动灭火系统的自动化程序和可靠性比常规电站有更高的要求，本文重点介绍法国CEGELEG（集团）公司消防设计特点，并对设计中存在的主要问题进行了分析。     

流量自动控制的设计与实现

文章通过分析多相流模拟井的实际工作要求 ,提出了简单实用的流量自动控制模型。应用成型的计算机数据采集和控制模块及稳定可靠的流量控制部件 ,实现了各相流量的自动控制过程。该流量自动控制系统调节精度高、速度快、整体造价低 ,在实际应用中取得了良好的效果。     

VLSI Implementation of Forward Error Control Technique for ATM Networks

In asynchronous transfer mode (ATM) networks, fixed length cells of 53 bytes are transmitted. A cell may be discarded during transmission due to buffer overflow or a detection of errors. Cell discarding seriously degrades transmission quality. The quality degradation can be reduced by employing efficient forward error control (FEC) to recover discarded cells. In this paper, we present the design and implementation of decoding equipment for FEC in ATM networks based on a single parity check (SPC) product code using very‐large‐scale integration (VLSI) technology. FEC allows the destination to reconstruct missing data cells by using redundant parity cells that the source adds to each block of data cells. The functionality of the design has been tested using the Model Sim 5.7cXE Simulation Package. The design has been implemented for a 5 ° 5 matrix of data cells in a Virtex‐E XCV 3200E FG1156 device. The simulation and synthesis results show that the decoding function can be completed in 81 clock cycles with an optimum clock of 56.8 MHz. A test bench was written to study the performance of the decoder, and the results are presented.     

一个用户接口管理系统

本文介绍了一个用户接口管理系统NUUIMS的设计和实现.重点叙述了该系统基于规范化目标用户接口模型的设计思想,系统组成及描述方法.文章也讨论了使用NUUIMS设计而成的用户接口的特点.     

方圆坯铸机开发新断面自动化程序的实现

文章介绍了包钢连铸机结晶器液位、喷淋水、热坯压力等主要参数实现自动控制的过程,阐述了上述参数如何根据不同铸坯断面而改变,并针对钢厂开发新断面如何实现参数的切换提出解决办法.     

给水泵密封水系统对机组真空的影响

介绍了银川热电厂二期工程投运一年以后,多次出现凝汽器真空缓慢下降的现象。在机组系统严密性试验合格的前提下,经多次观察,发现是给水泵密封水系统漏空气造成的。在采取了一些相应措施后,解决了这个问题。     

An Experimental Investigation into the Feed Rate Capacity of Rotary Valve and Blow Tank Feeders

Industry widely uses rotary valves and blow tanks for the pneumatic conveying of products, each having their pros and cons depending on the specific application. This article shows the differing results obtained when low-velocity conveying a product through a common pipeline using both a drop-through rotary valve and a bottom-discharge blow tank feeder. A number of issues arise in the rotary valve system, the main one being rotary valve air leakage. A blow tank system, on the other hand, does not leak, as it is an enclosed system. The experimental results show dramatic differences in product throughput. Further exploration leads to a novel modification being made to the rotary valve system in an attempt to increase its capacity. The result of this modification shows a slight increase in output tonnage, but still significantly less than that obtained from the blow tank.     

浅谈炼钢车间的自动控制系统

介绍了天津钢铁工业结构调整改造后的新钢铁企业炼钢车间的自动控制系统，系统的配置、主要功能，并对系统做出评价。