调速控制的轴流式通风机最小能耗运行条件的研究

针对轴流式通风机调速节能的问题 ,从通风机全压方程入手 ,利用最优控制原理 ,推导出了调速控制的轴流式通风机最小能耗运行条件 ,为此类通风机调速节能运行提供了理论依据     

桑车20MnCr5钢主动轴螺旋齿断裂分析

某大众试验车行驶8．6万公里后其主动轴螺旋齿断裂。采用宏观检验、金相分析、化学成分分析、应力测试等手段对失效件取样分析，结果表明，螺旋齿断裂是由于轴向定位松动，造成齿轮局部受力集中，在疲劳源基础上发展成裂纹，裂纹进一步扩展导致断裂。     

GH4169缺口件多轴加载下应力应变场的有限元分析

采用GH4169缺口试件在650 ℃下进行了高温拉扭疲劳断裂试验,利用ANSYS 6 1 有限元分析软件计算试件缺口周围的应力应变场,确定出试件在各种载荷状况下的应力集中系数。计算结果表明,该有限元建模方式是合理的,为以后缺口件的寿命预测过程奠定了基础。     

AXIAL PHASES DISTRIBUTION AND HOMOGENIZATION IN THREE-PHASE FLUIDIZED BEDS

We have investigated the axial distribution of the liquid phase in a three-phase fluidized bed in which the particles were glass beads of two different diameters, 710-850 μm and 2 mm. Two methods were used to reduce the axial heterogeneity and homogenize the bed: the use of packing elements and the addition of a small quantity of a high molecular weight polymer. The use of packing elements was shown to be very efficient in controlling phases distribution in the bed. The packing consisted of 1 mm thick steel horizontal plates punched and stretched to obtain parallelogram-shaped openings. The addition of a high molecular weight polyisobutylene (BASF Oppanol B246, M_u, =6.15 Lo⁶) on the phase distribution was also studied. Low polymer concentrations up to 397 ppm (based on the liquid phase) were investigated. The addition of the polymer reduced bubble coalescence and allowed for a better distribution of the phases.     

Hydrodynamics and liquid phase axial mixing in orifice pipe reactor

Two phase flow in a horizontal pipe, with orifice plates placed at regular intervals as obstructions, was studied for the effect of phase velocities on flow patterns, fractional phase hold-ups, pressure drop and liquid phase axial dispersion. Radioactive technetium-99m (as an aqueous solution of sodium pertechnatate) was used as tracer. A pulse injection technique with two point measurements was employed. Three different orifice diameters were used (8 mm, 16 mm, and 20 mm) in a pipe diameter of 32 mm. The orifice spacing was 500 mm in all cases. Superficial gas (air) velocity was varied over a range from 0.02 m/s to 1.0 m/s and superficial liquid (water) velocity from 0.03 m/s to 0.85 m/s. Different flow patterns under different flow conditions were identified and a generalised flow map is presented. Variations in hold-ups and pressure drop with flow patterns have been explained. Rational correlations have been developed for fractional phase hold-ups and pressure drop. A preliminary comparison of two phase gas-liquid flow in a horizontal pipe with orifice obstructions (to be called orifice pipe reactor), as a gas-liquid contacting device, is made with a conventional bubble column reactor. Recommendations have been made for future work.     

GRIP管混凝土组合结构压弯构件非线性全过程分析

本文应用细观力学、经典层板理论、平截面假定、FRP约束混凝土本构模型及数值积分对GFRP管混凝土组合结构压弯构件进行了非线性全过程分析。通过理论计算发现GFRP管混凝土组合结构能有效地提高构件的承载力，且构件具有良好的变形能力。FRP壳体参与承载且有效地约束混凝土的变形，显著提高核心混凝土强度和变形能力。文中讨论了轴压比、长细比、径厚比、混凝土强度等级、纵筋配筋率、铺层角变化对极限水平荷载和极限水平位移的影响，从而得到了一些有益的结论。     

回转窑传热模型与数值模拟

对回转窑内传热过程进行了分析 ,在已有研究基础上归纳了各项换热系数的关联式 ,尤其结合热渗透模型完善了回转壁面与料床之间传热机制的研究 ,并提出通用的计算关联式。进而提出了内热式炉型的一维轴向传热模型 ,并根据已发表的试验数据验证了该模型和各换热系数的适用性。计算表明在窑内低温段 ,物料的受热主要来自其覆盖的回转壁面对其加热 ;而在高温段 ,气体的辐射热量成为加热料床的主要热源。此外 ,由物料进口端沿轴向窑壁散热增大 ,在窑内高温段窑壁的散热甚至高于物料吸热量 ,因此在回转反应器的设计中应充分考虑窑壁散热造成的热效率降低并采取相应措施。     

快速闸门断流的轴流泵起动过程三维数值模拟

针对轴流泵机组起动过程的研究是泵站安全稳定运行研究的重要环节。为了准确捕捉轴流泵机组在起动过渡过程中的动态特性,建立轴流泵机组的全流道三维模型,采用三维CFD计算软件Fluent,利用基于有限体积法的动网格技术,配合VOF多相流模型对快速闸门断流的轴流泵机组起动过程进行了三维瞬态数值模拟,获得了轴流泵机组起动过渡过程中的流态变化及外特性参数的变化规律。闸门开启时间为60s时,机组起动扬程在12s时达到最大值2.76m,为运行扬程的1.28倍。减小快速闸门开启时间能够降低机组最大起动扬程,但同时会加剧回流及闸门处的水流撞击。计算结果表明:动网格技术结合VOF多相流模型可以较好的应用于快速闸门断流的轴流泵机组起动过渡过程数值模拟中,其结果可为泵站水力设计及轴流泵机组的过渡过程研究提供参考。     

竖向荷载作用下斜桩承载特性数值分析

近年来,斜桩在桥梁、码头、海上钻井平台及大型输电线路塔架基础等工程中得到广泛应用,研究不同倾角斜桩的荷载传递及承载特性实用意义较大。基于ABAQUS软件,考虑桩土接触特性,模拟分析了不同倾角斜桩的承载特性。结果表明:桩身倾角不大于10°时,倾斜角对单桩的极限承载力影响不大,但会在桩身产生一定弯矩以及桩顶产生一定的水平位移;桩身轴力沿桩长方向的衰减速率随桩身倾角的增大而增大;斜桩桩身弯矩主要分布在桩顶下1/2桩长范围内,其最大值的位置不受桩身倾角以及桩顶竖向荷载的影响;斜桩桩身侧摩阻力沿桩长大致呈"S"型分布,其桩顶以下1/6桩长范围内侧摩阻力远远大于直桩。     

一次风机节能改造

为解决一次风机出口风压低、火焰无力度、系统功耗高等问题,采用空气悬浮风机对其进行节能改造。拆除原有的一次风机备用风机,在原有底座上安装空气悬浮风机,整体设计安装悬浮风机出口管道。改造后,一次风机出口风压明显增大,煤粉燃烧充分,火焰调整灵活,每小时可节电30kWh,两处对空排放管道加装消声器,降噪效果显著。